Gefen EXT-DVI-16416 manual IP Control Main

Page 32

IP CONTROL - MAIN PAGE

The 16x16 DVI Matrix supports IP based control via an IP Control. To access this feature an IP address, subnet, gateway, and port need to be set on the

16x16 DVI Matrix (Default IP: 192.168.0.70 Subnet: 255.255.255.0 Gateway:

192.168.0.1 Port: 80). These settings must fall within your networks IP address range. Please consult your network administrator to obtain the proper IP address and settings for this product to properly communicate on your network.

The IP control setting can be configured via the RS-232 control interface. Once this has been accomplished, access using IP Control is possible.

Simply type the IP address that was assigned to the product in a web browser to access the Main Page. It should look like the image below.

MAIN PAGE

The Main Page will display the current status and can also be used to create routes.

To create a new route, follow the steps below:

1.Click on the check boxes of all of the outputs that you would like to route an input to.

2.Click on the input that will be routed to the selected outputs.

3.Click the “Switch” button to initiate the change(s).

This page will automatically refresh every minute, however, at anytime the “Refresh” button can be pressed to refresh the status of the matrix.

29

Image 32
Contents Page Asking for Assistance Technical SupportTechnical Support Hours Write ToContents Introduction GefenGefen 16x16 DVI Matrix How It WorksOperation Notes Features Package IncludesPanel Layout Panel Descriptions Main LCD DisplayHow to Operate the 16x16 DVI Matrix Connecting and Operating the 16X16 DVI MatrixHow to Connect the 16x16 DVI Matrix Front Panel Display Main DisplayRouting Routing Sources to Displays RMT-16416IR Remote DescriptionRMT-16416IR RMT-16416IR Remote Installation Empty Battery Slot IR Code Dip SwitchesRMT-16416IR Remote Configuration How to Resolve IR Code ConflictsExiting Standby Mode Standby Mode FeatureInvoking Standby Mode Edid Management Feature EDID. What is it and what is it used for?How do I use these features? RS-232 Serial Control InterfaceRS-232 Serial Control Commands RS-232 FeaturesCommand Description CommandParam1 Parameters Param1 InputF command returns the state of pin 14 of the DVI inputs #EDIDDSTOLO 2 1 2 3 4 5 6 7 8 9 10 11 not permitted #EDIDDSTOLO Function#EDIDDSTOLO param1 param2 param3...param9 #EDIDDSTOBA Function #EDIDBATOLO Function#EDIDDETOLO Function #EDIDDETOLO param1 param2 param3...param9#LOEDIDTOLO Function #LOEDIDTOLO param1 param2 param3#PRBAEDID Function #PRDSEDID Function#PRLOEDID Function #LOCKEDID param1 #PREDIDST Function#LOCKEDID Function #SIPADD Function #SIPADD param1 param2 param3 param4#SNETMASK Function #SNETMASK param1 param2 param3 param4#SGATEWAY Function #SGATEWAY param1 param2 param3 param4#RSTIP Function #SPORT param1#PRWEBADD Function #RMTIRADD param1 #FADEFAULT Function#RMTIRADD Function #ACTIVEBOLO Function #MASKOUT Function#MASKOUT param1 param2 #LOCKPOWER Function #LOCKPOWER param1#STBYMODE Function #STBYMODE param1IP Control Main MainIP Control Manage Edid Manage EdidSET Input to Default Edid Copy Edid IP Control Masking MaskingIP Control IP Configuration IP ConfigurationIP Control BACKUP/RESTORE & Power Management Power ManagementSwitching and Masking without the Web Interface SwitchingIP Control Management Without the WEB Interface Single OutputSwitching Table Http//192.168.0.70/cgibin.shtml?a=s&o=0&i=0Http//192.168.0.70/cgibin.shtml?a=s&o=a&i=2 Http//192.168.0.70/cgibin.shtml?a=s&o=0&o=1&o=2&o=3&i=0Masking Masking TableHttp//192.168.0.70/cgibin.shtml?a=m&o5=0&oA=1&o3=1&oF=0 Masking CommandHttp//192.168.0.70/cgibin.shtml?a=m&o0=1 Firmware Update =========================================================Waiting for the file to be sent ... press ‘a’ to abort 16x16Fan Failure System FailureCritical Malfunctions Temperature Failure Power FailureSpecifications Warranty Product RegistrationLicensing