Fortinet Version 3.0 manual FortiBridge unit basic information, FortiBridge-1000 Package contents

Page 19


Setting up FortiBridge units	FortiBridge unit basic information

Setting up FortiBridge units

This chapter contains the information you need to unpack, connect, and configure your FortiBridge unit:

•FortiBridge unit basic information

•Connecting and turning on the FortiBridge unit

•Connecting to the command line interface (CLI)

•Completing the basic FortiBridge configuration

•Resetting to the factory default configuration

•Installing FortiBridge unit firmware

When you complete the procedures in this chapter, the FortiBridge unit will be operating and connected to your network and to your FortiGate unit. See “Configuration and operating procedures” on page 35 to configure the FortiBridge unit to monitor the status of the FortiGate unit and to fail open if the FortiBridge unit detects that the FortiGate unit has failed.

FortiBridge unit basic information

This section describes the following basic information about the FortiBridge units:

•FortiBridge-1000 Package contents

•Mounting instructions

•Technical specifications

•LED indicators

•Connectors

•Factory default configuration

FortiBridge-1000 Package contents

The FortiBridge-1000 package contains the following items:

•the FortiBridge-1000 unit

•two orange crossover Ethernet cables (Fortinet part number CC300248)

•one RJ-45 to DB-9 serial cable (Fortinet part number CC300302)

•FortiBridge-1000 QuickStart Guide

•CD containing the Fortinet user documentation

•one AC adapter

FortiBridge Version 3.0 Administration Guide	19
09-30000-0163-20061109

Image 19

Contents M i n i s t r a t i o n G u i d e Regulatory compliance TrademarksContents Using the CLI Configuration and operating proceduresConfig CLI commands Index Execute CLI commandsPage About this document About FortiBridgeFortinet Knowledge Center Customer service and technical supportFortinet documentation Fortinet tools and documentation CDExample FortiBridge application FortiBridge operating principlesConnecting the FortiBridge-1000 copper gigabit ethernet Connecting the FortiBridge unitConnecting the FortiBridge-1000F fiber gigabit ethernet Normal mode operationHow the FortiBridge unit monitors the FortiGate unit Probes and FortiGate firewall policies Normal mode operationEnabling probes to detect FortiGate software failure Enabling probes to detect FortiGate hardware failureProbe interval and probe threshold FortiBridge power failure Bypass mode operationExample FortiGate HA cluster FortiBridge application Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces FortiBridge unit basic information FortiBridge-1000 Package contentsMounting instructions FortiBridge-1000F Package contentsLED indicators Technical specificationsFactory default configuration ConnectorsConnecting and turning on the FortiBridge-1000 unit Connecting and turning on the FortiBridge unitTo connect and turn on the FortiBridge-1000 unit Connecting and turning on the FortiBridge-1000F unitTo connect and turn on the FortiBridge-1000F unit To connect to the FortiBridge console for the first time Connecting to the command line interface CLIConnecting to the FortiBridge console FortiBridge-1000 loginWelcome FortiBridge-1000 # Completing the basic FortiBridge configurationConnecting to the FortiBridge CLI using Telnet To connect to the CLI using TelnetTo change the management IP address Adding an administrator passwordTo add an administrator password Changing the management IP addressTo add static routes Changing DNS server IP addressesAdding static routes To change DNS server IP addressesAdding administrator accounts Allowing management access to the EXT 1 interfaceChanging the system time and date Installing FortiBridge unit firmware Resetting to the factory default configurationTo reset to factory defaults from the FortiBridge CLI Upgrading to a new firmware version To upgrade to a new firmware versionExecute restore image namestr tftpip Execute restore image FBG1000-v10-build010-FORTINET.outTo revert to a previous firmware version Reverting to a previous firmware versionEnter Tftp server address Installing firmware from a system rebootTo install firmware from a system reboot Hit any key to stop autobootGet system status Enter firmware image file image.outExample network settings Configuration and operating proceduresConfiguring FortiBridge probes Configuring FortiBridge probesTo configure probe settings Probe settingsConfig probe probelist ping set status enable End To enable and configure FortiBridge probesEnabling probes Go to System Status Session Config probe probelist Imap set status enable EndVerifying that probes are functioning To verify that probes are functioningTuning the failure threshold and probe interval Configuring FortiBridge alertsFortiBridge syslog To configure alert emailConfig alertemail setting set server mail.myorg.com End FortiBridge alert emailConfig log syslogd setting set server End To configure FortiBridge syslogFortiBridge Snmp To resume normal operation from bypass mode Recovering from a FortiGate failureTo add and enable an Snmp community Config system snmp community edit Set name snmp1 EndTo back up the FortiBridge configuration Manually switching between FortiBridge operating modesBacking up and restoring the FortiBridge configuration Execute switch-modeBacking up and restoring the FortiBridge configuration Backing up and restoring the FortiBridge configuration CLI basics Connecting to the FortiBridge CLI using SSH or TelnetSetting administrative access for SSH or Telnet To use the CLI to configure SSH or Telnet accessGet system interface namestr Other access methodsConnecting to the FortiBridge CLI using SSH Set allowaccess ping telnet sshTo connect to the CLI using SSH Connecting to the FortiBridge CLI using SSH or Telnet Config CLI commands Command syntax pattern Alertemail settingExamples Related Commands Example Log syslogd settingShow probe probelist Probe probelist ping http ftp pop3 smtp imapGet probe probelist Get probe probelist httpSyslog Probe settingRw w System accprofileGet system accprofile policyprofile Get system accprofileShow system accprofile Password passwordstr System adminGet system admin newadmin Get system adminShow system admin Show system console Config system console set EndSystem console Get system consoleGet system dns System dnsShow system dns Get system status Failbypass System failcloseSystem failclose Minutesinteger System globalShow system global Get system globalGet system interface internal System interface internal externalShow system interface internal System manageip Config system manageip Set ip 192.168.2.80 255.255.255.0 endDistanceinteger System routeSystem snmp community Config hostsShow system snmp community Get system snmp communityExecute CLI commands Execute backup config fbdg.cfg BackupCommand syntax Execute backup config filenamestr tftp-serveripv4Execute date datestr datestr has the form mm/dd/yyyy, where DateExecute date 09/17/2004 Execute factoryreset FactoryresetExecute ping addressipv4 host-namestr PingExecute reboot RebootExecute restore config backupconfig RestoreSwitch-mode Execute time timestr TimeTime Index 09-30000-0163-20061109 Snmp SSH