Fortinet Version 3.0 manual Installing firmware from a system reboot, Hit any key to stop autoboot

Page 33

 

 

Setting up FortiBridge units

Installing FortiBridge unit firmware

Installing firmware from a system reboot

This procedure installs a specified firmware image and resets the FortiBridge unit to default settings. You can use this procedure to upgrade to a new firmware version, revert to an older firmware version, or to re-install the current firmware.

To use this procedure you:

access the CLI by connecting to the FortiBridge console port,

install a TFTP server that you can connect to from the FortiBridge EXT 2 interface. The TFTP server should be on the same network as the EXT 2 interface. The FortiBridge unit cannot access the TFTP server if its behind a router.

During this procedure you will be asked to enter a local IP address for the FortiBridge unit. This is a temporary address used for downloading the firmware image.

This procedure reverts your FortiBridge unit to its factory default configuration. Before running this procedure you can backup the FortiBridge unit configuration using the command execute backup config.

To install firmware from a system reboot

1Connect to the CLI using the FortiBridge console port.

2Make sure the TFTP server is running.

3Copy the new firmware image file to the root directory of the TFTP server.

4Make sure the EXT 2 interface of the FortiBridge unit can connect to the TFTP server.

5Enter the following command to restart the FortiBridge unit: execute reboot

As the FortiBridge unit starts, a series of system startup messages are displayed. When the following messages appears:

Hit any key to stop autoboot:

6Immediately press any key to interrupt the system startup.

Note: You only have 3 seconds to press any key. If you do not press any key soon enough, the FortiBridge unit reboots and you must log in and repeat the execute reboot command.

When you successfully interrupt the startup process, the => prompt appears:

7Type upgrade and press Enter to get the new firmware image from the TFTP server.

The following message appears:

Enter TFTP server address [192.168.1.168]:

8Type the address of the TFTP server and press Enter. The following message appears:

Enter local address [192.168.1.188]:

9Type an IP address that the FortiBridge unit can use to connect to the TFTP server press Enter.

FortiBridge Version 3.0 Administration Guide

33

09-30000-0163-20061109

Image 33
Contents M i n i s t r a t i o n G u i d e Regulatory compliance TrademarksContents Configuration and operating procedures Using the CLIConfig CLI commands Index Execute CLI commandsPage About this document About FortiBridgeFortinet documentation Customer service and technical supportFortinet tools and documentation CD Fortinet Knowledge CenterExample FortiBridge application FortiBridge operating principlesConnecting the FortiBridge-1000 copper gigabit ethernet Connecting the FortiBridge unitNormal mode operation Connecting the FortiBridge-1000F fiber gigabit ethernetHow the FortiBridge unit monitors the FortiGate unit Probes and FortiGate firewall policies Normal mode operationEnabling probes to detect FortiGate hardware failure Enabling probes to detect FortiGate software failureProbe interval and probe threshold FortiBridge power failure Bypass mode operationExample FortiGate HA cluster FortiBridge application Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces FortiBridge unit basic information FortiBridge-1000 Package contentsMounting instructions FortiBridge-1000F Package contentsLED indicators Technical specificationsFactory default configuration ConnectorsConnecting and turning on the FortiBridge-1000 unit Connecting and turning on the FortiBridge unitConnecting and turning on the FortiBridge-1000F unit To connect and turn on the FortiBridge-1000 unitTo connect and turn on the FortiBridge-1000F unit Connecting to the FortiBridge console Connecting to the command line interface CLIFortiBridge-1000 login To connect to the FortiBridge console for the first timeConnecting to the FortiBridge CLI using Telnet Completing the basic FortiBridge configurationTo connect to the CLI using Telnet Welcome FortiBridge-1000 #To add an administrator password Adding an administrator passwordChanging the management IP address To change the management IP addressAdding static routes Changing DNS server IP addressesTo change DNS server IP addresses To add static routesAllowing management access to the EXT 1 interface Adding administrator accountsChanging the system time and date Resetting to the factory default configuration Installing FortiBridge unit firmwareTo reset to factory defaults from the FortiBridge CLI Execute restore image namestr tftpip To upgrade to a new firmware versionExecute restore image FBG1000-v10-build010-FORTINET.out Upgrading to a new firmware versionTo revert to a previous firmware version Reverting to a previous firmware versionTo install firmware from a system reboot Installing firmware from a system rebootHit any key to stop autoboot Enter Tftp server addressGet system status Enter firmware image file image.outExample network settings Configuration and operating proceduresConfiguring FortiBridge probes Configuring FortiBridge probesTo configure probe settings Probe settingsTo enable and configure FortiBridge probes Config probe probelist ping set status enable EndEnabling probes Verifying that probes are functioning Config probe probelist Imap set status enable EndTo verify that probes are functioning Go to System Status SessionTuning the failure threshold and probe interval Configuring FortiBridge alertsConfig alertemail setting set server mail.myorg.com End To configure alert emailFortiBridge alert email FortiBridge syslogTo configure FortiBridge syslog Config log syslogd setting set server EndFortiBridge Snmp To add and enable an Snmp community Recovering from a FortiGate failureConfig system snmp community edit Set name snmp1 End To resume normal operation from bypass modeBacking up and restoring the FortiBridge configuration Manually switching between FortiBridge operating modesExecute switch-mode To back up the FortiBridge configurationBacking up and restoring the FortiBridge configuration Backing up and restoring the FortiBridge configuration Setting administrative access for SSH or Telnet Connecting to the FortiBridge CLI using SSH or TelnetTo use the CLI to configure SSH or Telnet access CLI basicsConnecting to the FortiBridge CLI using SSH Other access methodsSet allowaccess ping telnet ssh Get system interface namestrTo connect to the CLI using SSH Connecting to the FortiBridge CLI using SSH or Telnet Config CLI commands Alertemail setting Command syntax patternExamples Related Commands Example Log syslogd settingGet probe probelist Probe probelist ping http ftp pop3 smtp imapGet probe probelist http Show probe probelistSyslog Probe settingRw w System accprofileGet system accprofile Get system accprofile policyprofileShow system accprofile Password passwordstr System adminGet system admin Get system admin newadminShow system admin System console Config system console set EndGet system console Show system consoleSystem dns Get system dnsShow system dns Get system status Failbypass System failcloseSystem failclose Minutesinteger System globalShow system global Get system globalSystem interface internal external Get system interface internalShow system interface internal System manageip Config system manageip Set ip 192.168.2.80 255.255.255.0 endDistanceinteger System routeSystem snmp community Config hostsShow system snmp community Get system snmp communityExecute CLI commands Command syntax BackupExecute backup config filenamestr tftp-serveripv4 Execute backup config fbdg.cfgDate Execute date datestr datestr has the form mm/dd/yyyy, whereExecute date 09/17/2004 Execute factoryreset FactoryresetExecute ping addressipv4 host-namestr PingExecute reboot RebootExecute restore config backupconfig RestoreSwitch-mode Execute time timestr TimeTime Index 09-30000-0163-20061109 Snmp SSH