Fortinet Version 3.0 Changing DNS server IP addresses, Adding static routes, To add static routes

Page 28

Completing the basic FortiBridge configuration

Setting up FortiBridge units

Changing DNS server IP addresses

Change the FortiBridge DNS server IP addresses to the IP addresses of your DNS servers. The correct DNS server configuration is required for alert email.

To change DNS server IP addresses

1Log in to the CLI.

2Change the primary and secondary DNS server IP addresses. Enter:

config system dns

set primary <address_ipv4> set secondary <address_ipv4>

end

For example:

config system dns

set primary 192.168.30.23 set secondary 192.168.30.24

end

Adding static routes

Add static routes if you need to route packets from the FortiBridge unit through a router to another network. For example, if alert email sends email messages from the internal network to an email server on the Internet, you should add a route to the Internet.

To add static routes

1Log in to the CLI.

2Add the default route. Enter:

config system route

edit <sequence_integer>

set gateway <gateway-address_ipv4>

end

For example:

config system route edit 1

set gateway 192.168.20.1

end

3If required for your network configuration, add a static route. Enter:

config system route

edit <sequence_integer>

set gateway <gateway-address_ipv4>

set dst <destination-address_ipv4mask>

end

For example:

config system route edit 2

set gateway 192.168.20.3

set dst 192.168.22.0 255.255.255.0

end

28

FortiBridge Version 3.0 Administration Guide

09-30000-0163-20061109

Image 28
Contents M i n i s t r a t i o n G u i d e Trademarks Regulatory complianceContents Using the CLI Configuration and operating proceduresConfig CLI commands Execute CLI commands IndexPage About FortiBridge About this documentCustomer service and technical support Fortinet documentationFortinet tools and documentation CD Fortinet Knowledge CenterFortiBridge operating principles Example FortiBridge applicationConnecting the FortiBridge unit Connecting the FortiBridge-1000 copper gigabit ethernetConnecting the FortiBridge-1000F fiber gigabit ethernet Normal mode operationHow the FortiBridge unit monitors the FortiGate unit Normal mode operation Probes and FortiGate firewall policiesEnabling probes to detect FortiGate software failure Enabling probes to detect FortiGate hardware failureProbe interval and probe threshold Bypass mode operation FortiBridge power failureExample FortiGate HA cluster FortiBridge application Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces FortiBridge-1000 Package contents FortiBridge unit basic informationFortiBridge-1000F Package contents Mounting instructionsTechnical specifications LED indicatorsConnectors Factory default configurationConnecting and turning on the FortiBridge unit Connecting and turning on the FortiBridge-1000 unitTo connect and turn on the FortiBridge-1000 unit Connecting and turning on the FortiBridge-1000F unitTo connect and turn on the FortiBridge-1000F unit Connecting to the command line interface CLI Connecting to the FortiBridge consoleFortiBridge-1000 login To connect to the FortiBridge console for the first timeCompleting the basic FortiBridge configuration Connecting to the FortiBridge CLI using TelnetTo connect to the CLI using Telnet Welcome FortiBridge-1000 #Adding an administrator password To add an administrator passwordChanging the management IP address To change the management IP addressChanging DNS server IP addresses Adding static routesTo change DNS server IP addresses To add static routesAdding administrator accounts Allowing management access to the EXT 1 interfaceChanging the system time and date Installing FortiBridge unit firmware Resetting to the factory default configurationTo reset to factory defaults from the FortiBridge CLI To upgrade to a new firmware version Execute restore image namestr tftpipExecute restore image FBG1000-v10-build010-FORTINET.out Upgrading to a new firmware versionReverting to a previous firmware version To revert to a previous firmware versionInstalling firmware from a system reboot To install firmware from a system rebootHit any key to stop autoboot Enter Tftp server addressEnter firmware image file image.out Get system statusConfiguration and operating procedures Example network settingsConfiguring FortiBridge probes Configuring FortiBridge probesProbe settings To configure probe settingsConfig probe probelist ping set status enable End To enable and configure FortiBridge probesEnabling probes Config probe probelist Imap set status enable End Verifying that probes are functioningTo verify that probes are functioning Go to System Status SessionConfiguring FortiBridge alerts Tuning the failure threshold and probe intervalTo configure alert email Config alertemail setting set server mail.myorg.com EndFortiBridge alert email FortiBridge syslogConfig log syslogd setting set server End To configure FortiBridge syslogFortiBridge Snmp Recovering from a FortiGate failure To add and enable an Snmp communityConfig system snmp community edit Set name snmp1 End To resume normal operation from bypass modeManually switching between FortiBridge operating modes Backing up and restoring the FortiBridge configurationExecute switch-mode To back up the FortiBridge configurationBacking up and restoring the FortiBridge configuration Backing up and restoring the FortiBridge configuration Connecting to the FortiBridge CLI using SSH or Telnet Setting administrative access for SSH or TelnetTo use the CLI to configure SSH or Telnet access CLI basicsOther access methods Connecting to the FortiBridge CLI using SSHSet allowaccess ping telnet ssh Get system interface namestrTo connect to the CLI using SSH Connecting to the FortiBridge CLI using SSH or Telnet Config CLI commands Command syntax pattern Alertemail settingExamples Related Commands Log syslogd setting ExampleProbe probelist ping http ftp pop3 smtp imap Get probe probelistGet probe probelist http Show probe probelistProbe setting SyslogSystem accprofile Rw wGet system accprofile policyprofile Get system accprofileShow system accprofile System admin Password passwordstrGet system admin newadmin Get system adminShow system admin Config system console set End System consoleGet system console Show system consoleGet system dns System dnsShow system dns Get system status System failclose FailbypassSystem failclose System global MinutesintegerGet system global Show system globalGet system interface internal System interface internal externalShow system interface internal Config system manageip Set ip 192.168.2.80 255.255.255.0 end System manageipSystem route DistanceintegerConfig hosts System snmp communityGet system snmp community Show system snmp communityExecute CLI commands Backup Command syntaxExecute backup config filenamestr tftp-serveripv4 Execute backup config fbdg.cfgExecute date datestr datestr has the form mm/dd/yyyy, where DateExecute date 09/17/2004 Factoryreset Execute factoryresetPing Execute ping addressipv4 host-namestrReboot Execute rebootRestore Execute restore config backupconfigSwitch-mode Time Execute time timestrTime Index 09-30000-0163-20061109 Snmp SSH