Fortinet Version 3.0 manual Connecting to the command line interface CLI, FortiBridge-1000 login

Page 25


Setting up FortiBridge units	Connecting to the command line interface (CLI)

3Connect the internal network to the FortiBridge-1000F INT 1 interface.

4Connect the FortiBridge-1000F EXT 1 interface to the router.

Connecting to the command line interface (CLI)

You configure and manage the FortiBridge unit from the FortiBridge command line interface (CLI). You can use a direct console connection, SSH, or Telnet to connect to the FortiBridge CLI. This section describes how to connect directly to the FortiBridge console and how to connect to the FortiBridge CLI across an ethernet network using Telnet. See also “Connecting to the FortiBridge CLI using Telnet” on page 26 for more information about connecting to the FortiBridge CLI.

Connecting to the FortiBridge console

You require:

•A computer with an available communications port,

•An RJ-45 to DB-9 serial cable,

•Terminal emulation software such as HyperTerminal for Windows.

Note: The following procedure describes how to connect to the FortiBridge CLI using

Windows HyperTerminal software. You can use any terminal emulation software.

To connect to the FortiBridge console for the first time

1Connect the FortiBridge console port to the available communications port on your computer.

2Make sure the FortiBridge unit is powered on.

3Start HyperTerminal, enter a name for the connection, and select OK.

4Configure HyperTerminal to connect directly to the communications port on the computer to which you have connected the FortiBridge console port.

5Select OK.

6Select the following port settings and select OK.

Bits per second	9600
Data bits	8
Parity	None
Stop bits	1
Flow control	None

7Press the escape key (Esc) to connect to the FortiBridge CLI.

A prompt similar to the following appears (shown for the FortiBridge-1000):

FortiBridge-1000 login:

8Type a valid administrator name and press Enter. The default administrator account is admin.

FortiBridge Version 3.0 Administration Guide	25
09-30000-0163-20061109

Image 25

Contents M i n i s t r a t i o n G u i d e Regulatory compliance TrademarksContents Using the CLI Configuration and operating proceduresConfig CLI commands Index Execute CLI commandsPage About this document About FortiBridgeFortinet documentation Customer service and technical supportFortinet tools and documentation CD Fortinet Knowledge CenterExample FortiBridge application FortiBridge operating principlesConnecting the FortiBridge-1000 copper gigabit ethernet Connecting the FortiBridge unitConnecting the FortiBridge-1000F fiber gigabit ethernet Normal mode operationHow the FortiBridge unit monitors the FortiGate unit Probes and FortiGate firewall policies Normal mode operationEnabling probes to detect FortiGate software failure Enabling probes to detect FortiGate hardware failureProbe interval and probe threshold FortiBridge power failure Bypass mode operationExample FortiGate HA cluster FortiBridge application Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces FortiBridge unit basic information FortiBridge-1000 Package contentsMounting instructions FortiBridge-1000F Package contentsLED indicators Technical specificationsFactory default configuration ConnectorsConnecting and turning on the FortiBridge-1000 unit Connecting and turning on the FortiBridge unitTo connect and turn on the FortiBridge-1000 unit Connecting and turning on the FortiBridge-1000F unitTo connect and turn on the FortiBridge-1000F unit Connecting to the FortiBridge console Connecting to the command line interface CLIFortiBridge-1000 login To connect to the FortiBridge console for the first timeConnecting to the FortiBridge CLI using Telnet Completing the basic FortiBridge configurationTo connect to the CLI using Telnet Welcome FortiBridge-1000 #To add an administrator password Adding an administrator passwordChanging the management IP address To change the management IP addressAdding static routes Changing DNS server IP addressesTo change DNS server IP addresses To add static routesAdding administrator accounts Allowing management access to the EXT 1 interfaceChanging the system time and date Installing FortiBridge unit firmware Resetting to the factory default configurationTo reset to factory defaults from the FortiBridge CLI Execute restore image namestr tftpip To upgrade to a new firmware versionExecute restore image FBG1000-v10-build010-FORTINET.out Upgrading to a new firmware versionTo revert to a previous firmware version Reverting to a previous firmware versionTo install firmware from a system reboot Installing firmware from a system rebootHit any key to stop autoboot Enter Tftp server addressGet system status Enter firmware image file image.outExample network settings Configuration and operating proceduresConfiguring FortiBridge probes Configuring FortiBridge probesTo configure probe settings Probe settingsConfig probe probelist ping set status enable End To enable and configure FortiBridge probesEnabling probes Verifying that probes are functioning Config probe probelist Imap set status enable EndTo verify that probes are functioning Go to System Status SessionTuning the failure threshold and probe interval Configuring FortiBridge alertsConfig alertemail setting set server mail.myorg.com End To configure alert emailFortiBridge alert email FortiBridge syslogConfig log syslogd setting set server End To configure FortiBridge syslogFortiBridge Snmp To add and enable an Snmp community Recovering from a FortiGate failureConfig system snmp community edit Set name snmp1 End To resume normal operation from bypass modeBacking up and restoring the FortiBridge configuration Manually switching between FortiBridge operating modesExecute switch-mode To back up the FortiBridge configurationBacking up and restoring the FortiBridge configuration Backing up and restoring the FortiBridge configuration Setting administrative access for SSH or Telnet Connecting to the FortiBridge CLI using SSH or TelnetTo use the CLI to configure SSH or Telnet access CLI basicsConnecting to the FortiBridge CLI using SSH Other access methodsSet allowaccess ping telnet ssh Get system interface namestrTo connect to the CLI using SSH Connecting to the FortiBridge CLI using SSH or Telnet Config CLI commands Command syntax pattern Alertemail settingExamples Related Commands Example Log syslogd settingGet probe probelist Probe probelist ping http ftp pop3 smtp imapGet probe probelist http Show probe probelistSyslog Probe settingRw w System accprofileGet system accprofile policyprofile Get system accprofileShow system accprofile Password passwordstr System adminGet system admin newadmin Get system adminShow system admin System console Config system console set EndGet system console Show system consoleGet system dns System dnsShow system dns Get system status Failbypass System failcloseSystem failclose Minutesinteger System globalShow system global Get system globalGet system interface internal System interface internal externalShow system interface internal System manageip Config system manageip Set ip 192.168.2.80 255.255.255.0 endDistanceinteger System routeSystem snmp community Config hostsShow system snmp community Get system snmp communityExecute CLI commands Command syntax BackupExecute backup config filenamestr tftp-serveripv4 Execute backup config fbdg.cfgExecute date datestr datestr has the form mm/dd/yyyy, where DateExecute date 09/17/2004 Execute factoryreset FactoryresetExecute ping addressipv4 host-namestr PingExecute reboot RebootExecute restore config backupconfig RestoreSwitch-mode Execute time timestr TimeTime Index 09-30000-0163-20061109 Snmp SSH