Enterasys Networks C2RPS-CHAS2 manual 5 C2RPS-PSM Cable and AC Power Cord Connections

Page 29
Figure 2-5 C2RPS-PSM Cable and AC Power Cord Connections

Connecting the PSM Cables and AC Power Cords

Figure 2-5 C2RPS-PSM Cable and AC Power Cord Connections

STACK UP

STACK DOWN

 

 

 

Redundant Power Supply

AC LINE

100-240 VAC

50-60 Hz

0.8 A MAX

MAC ADDRESS SERIAL NO.

Â

Redundant Power Supply

À

Á

AC LINE

100-240 VAC

50-60 Hz

2A MAX

Ä

Ã

Å

1

Switch device

4

Switch device Redundant Power Supply connector

2

PSM cable

5

AC power cord (type varies depending on country)

3

PSM Redundant Power Supply

6

AC power outlet with ground connection

 

connector

 

(type varies depending on country)

5.On certain switches, an LED indicator will show that a redundant power supply is now in operation.

.

Note: No change in switch device configuration is necessary for this installation.

This completes the installation.

SecureStack C2 Installation Guide 2-7

Page 28 Page 30
Image 29
Page 28 Page 30
Contents C2RPS-CHAS2 SecureStack C2 Redundant Power Supply ChassisInstallation Guide Page Enterasys Networks, Inc 50 Minuteman Road Andover, MA Product Safety Regulatory Compliance InformationFederal Communications Commission FCC Notice Industry Canada NoticeCompatibilidad Electromágnetica EMC Electromagnetic Compatibility EMCElektro- magnetische Kompatibilität EMC VCCI NoticeDeclaration of Conformity BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT Enterasys Networks, Inc Firmware License AgreementCAREFULLY READ THIS LICENSE AGREEMENT You and Enterasys agree as follows3. APPLICABLE LAW. This Agreement shall be interpreted and governed under the laws and in the state and 9. OWNERSHIP. This is a license agreement and not an agreement for sale. You acknowledge and agree that the Program constitutes trade secrets and/or copyrighted material of Enterasys and/or its suppliers. You agree to implement reasonable security measures to protect such trade secrets and copyrighted material. All right, title and interest in and to the Program shall remain with Enterasys and/or its suppliers. All rights not specifically granted to You shall be reserved to Enterasys viii Chapter 2 Installation ContentsAppendix A Specifications About This GuideContents of C2RPS-CHAS2 Carton TablesContents of C2RPS-PSM Carton C2RPS-CHAS2 SpecificationsWho Should Use This Guide How to Use This GuideAbout This Guide Refer to Related DocumentsThe following conventions are used in this guide Conventions Used in This Guidexiv About This Guide RPS Overview IntroductionFor information about Refer to pageFigure 1-1 SecureStack C2RPS-CHAS2 front view without PSM C2RPS-CHAS2 ChassisFigure 1-2 SecureStack C2RPS-CHAS2 front view with two PSMs Figure 1-3 SecureStack C2RPS-CHAS2 rear view with two PSMsFigure 1-5 C2RPS-PSM rear view C2RPS-PSM Power Supply ModuleFigure 1-4 C2RPS-PSM front view Figure 1-6 RPS Supporting Two SecureStack Switches RPS Deployment StrategiesGetting Help 1-6 Introduction Required Tools InstallationUnpacking Chassis and Power Supply Modules Table 2-1 Contents of C2RPS-CHAS2 Carton Installing C2RPS-PSMsTable 2-2 Contents of C2RPS-PSM Carton QuantityFigure 2-1 C2RPS-PSM Installation Replacing an Installed C2RPS-PSMGuidelines for Rackmount Installation Installing C2RPS-CHAS2 into the RackFigure 2-2 Fastening the C2RPS-CHAS2 to the Rack Rack Mounting the ChassisFigure 2-3 C2RPS-PSM Cable Connecting the PSM Cables and AC Power CordsFigure 2-4 Power Connectors on C2RPS-PSM rear view This completes the installation Figure 2-5 C2RPS-PSM Cable and AC Power Cord Connections2-8 Installation C2RPS-CHAS2 Chassis Specifications SpecificationsTable A-1 C2RPS-CHAS2 Specifications SpecificationC2RPS-PSM Redundant Power Supply Output Connector C2RPS-PSM SpecificationsTable A-2 C2RPS-PSM Specifications Figure A-1 C2RPS-PSM Redundant Power Supply Connector Pin LocationsTable A-3 C2RPS-PSM Redundant Power Supply Connector Pin Functions Compliance StandardsPin Number FunctionA-4 Specifications
Top Page Image Contents