Enterasys Networks G3G170-24 manual Installing an IOM, Installing a PoE module in the G3G-24TX IOM

Page 37

Installing and Removing an IOM

Figure 2-3 Installing a PoE module in the G3G-24TX IOM

1

Fastening screws

4

IOM connector

2

PoE daughter card module

5

G3G-24TX IOM (motherboard)

3IOM to PoE connector

4.Using the screws shipped with the PoE module, firmly attach the PoE module to the IOM.

Installing an IOM

The following procedure describes how to install a hot‐swappable IOM into your G3G switch. You can install an IOM into any open slot. Enterasys Networks recommends inserting any IOMs before you connect power to the switch as described in Connecting Power to the Switch” on page 2‐13.

Note: An IOM can be hot-inserted into the G-Series switch, but must be removed by following the procedure described in Removing an IOM” on page 2-13.

Caution: If you are installing multiple IOMs into a switch that is running, you must wait until the previously installed IOM is completely initialized before attempting to install the next IOM. Initialization is complete when the slot’s status LED turns solid green. (A syslog message will also be sent to the CLI at completion.)

Precaución: Si instala varios IOM en un switch en funcionamiento, debe esperar a que el IOM que instaló previamente se haya activado por completo antes de pasar al siguiente. Se habrá completado la activación cuando el LED de estado pase a color verde (asimismo se enviará un mensaje syslog al CLI cuando se haya completado).

To install an IOM, refer to Figure 2‐4 on page 2‐12 and proceed as follows:

1.Confirm adequate power is available to power the new IOM. For more information about G3 power supplies, see Power Supply Installation Considerations” on page 2‐5. For more information about IOM power consumption, see IOM Specifications” on page A‐3.

2.Attach an ESD wrist strap to your wrist.

Enterasys G-Series Hardware Installation Guide 2-11

Image 37
Contents Enterasys G-Series Page Page Regulatory Compliance Information AS/NZS Cispr Supplement to Product Instructions Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety Information Class 1 Laser TransceiversDeclaration of Conformity Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix a Specifications TroubleshootingIndex Tables Xiv Who Should Use This Guide How to Use This GuideRelated Documents For information about Refer toCommonly Used Acronyms Document ConventionsGetting Help Getting Help Xviii About This Guide Overview IntroductionFeatures Standalone or Rack Mountable Chassis Powered Device Classifications PDs PoE Power over Ethernet SupportFan Management Features Features Introduction Installation Shipped With the Switch Unpacking the G-Series SwitchRequired and Shipped Separately Optional Enterasys ComponentsMounting the Switch Order of Installation StepsG3G124-24 Optional PoE Module Installation Considerations Installing the Switch into a Rack Placing the Switch on a Flat SurfacePower Supply Redundancy Power Supply Installation ConsiderationsSupported Power Configurations Power Distribution Upon Power Supply Removal or Addition Allocation of PoE Power to ModulesManagement of PoE Power to PDs Installing a Power SupplyPower supply Power supply handle Captive screws Removing a Power SupplyInstalling an Optional PoE Module on the G3G-24TX IOM Installing and Removing an IOMInstalling a PoE module in the G3G-24TX IOM Installing an IOMIOM slot IOM Initialization BehaviorIOM handle Removing an IOM Connecting Power to the SwitchConnecting to the RJ45 Console Port Connecting to the Console PortPower LED Displays Display StatusConsole Port Pinout Signal RJ45 Pin DB9 PinRJ45 to DB9 Adapter Pinout Pin ConnectionConnecting to the USB Console Port Connecting to the NetworkConnecting UTP Cables to RJ45 Ports Connecting a UTP Cable Segment to RJ45 Port TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Transceiver Type Switch or IOM Ports Installing Optional SFP/XFPConnecting to the Network Removing an XFP/SFP Connecting Fiber-Optic Cables to SFP/XFP PortsCompleting the Installation Removing the Switch Cover Installing an Optional PoE Module in the G3G124-24 SwitchInstalling the PoE Module Troubleshooting Checking the LEDs IOM power off status LEDs Slot 2, 3System LED Definitions Display StatusIOM Status LEDs Power LEDsFixed and IOM Port LEDs Locating the Password Reset button Using the Password Reset ButtonRemoving the Switch from a Rack Removing the Switch from a Rack Troubleshooting Table A-1 G3 Switch Specifications Switch SpecificationsSpecification G3G124-24 and G3G124-24PProcessors/Memory Power SpecificationsPerformance PhysicalIOM Specifications Power Supply SpecificationsTable A-2 Power Supply Specifications Table A-3 G3G-24TX IOM SpecificationsG3G-24SFP Table A-4 G3G-24SFP IOM SpecificationsG3K-2XFP and G3K-4XFP Table A-5 G3K-2XFP and G3K-4XFP IOM SpecificationsTable A-6 G3G-POE Specifications PoE Daughter Card SpecificationsTorque Values Table A-7 Recommended Torque Values by Screw SizeTable A-8 Mini-GBIC Input/Output Port Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXTable A-9 MGBIC-LC01/MGBIC-MT01 Optical Specifications Table A-10 MGBIC-LC01/MGBIC-MT01 Operating RangeMGBIC-LC03 Specifications 1000BASE-SX MGBIC-02 Specifications 1000BASE-TMGBIC-LC04 Specifications 100BASE-FX MGBIC-LC07 Specifications 1000BASE-ELX MGBIC-LC05 Specifications 100BASE-FXMGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELXTable A-24 XFP Specifications Gigabit Ethernet Transceiver XFP SpecificationsTable A-25 Recommended Cable Types and Specifications Console Port Pinout AssignmentsTable A-26 Compliance Standards Regulatory ComplianceRegulatory Compliance Standards Index Index-2
Related manuals
Manual 59 pages 23.28 Kb