Enterasys Networks G3G124-24, G3G124P-24, G3G170-24 manual MGBIC-LC05 Specifications 100BASE-FX

Page 65

1-Gigabit Ethernet and 100Base-FX Transceiver (SFP) Specifications

Table A-15 MGBIC LC04 Operating Range

Item

1310 nm

Range

 

 

 

9 or 10 µm SMF

N/A

2,000 Meters

 

 

 

MGBIC-LC05 Specifications (100BASE-FX)

Table A-16 MGBIC-LC05 Optical Specifications

Item

10 µm SMF

 

 

Transmit Power (minimum)

-15 dBm

 

 

Receive Sensitivity

-25 dBm

 

 

Link Power Budget 1

10 dBm

1.The maximum drive distance (up to 10 km) depends on the quality of the installed single-mode fiber-optic cable segment. Use the Link Power Budget to calculate the maximum cable length of the attached segment. The Link Power Budget must not exceed those specified in this table.

Table A-17 MGBIC LC05 Operating Range

Item

1310 nm

Range

 

 

 

9 or 10 µm SMF

N/A

10,000 Meters

 

 

 

MGBIC-LC07 Specifications (1000BASE-ELX)

Table A-18 MGBIC-LC07 Optical Specifications

Item

Transmit Power (minimum)

-2 dBm, min.

 

 

Receive Sensitivity

-30 dBm, min.

 

 

Maximum Input Power

-9 dBm

 

 

Link Power Budget1

28 dB

(Full Duplex Only)

1.The maximum drive distance (up to 110 km) depends on the quality of the installed single-mode fiber-optic cable segment. Use the Link Power Budget to calculate the maximum cable length of the attached segment. The Link Power Budget must not exceed those specified in this table. The MGBIC-LC07 input power must not exceed -9 dBm. Otherwise, saturation could occur.

Table A-19 MGBIC-LC07 Operating Range

Item

1550 nm

Range

 

 

 

9 or 10 µm SMF

N/A

110,000 Meters

 

 

 

Enterasys G-Series Hardware Installation Guide A-9

Image 65
Contents Enterasys G-Series Page Page Regulatory Compliance Information AS/NZS Cispr Supplement to Product Instructions Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety Information Class 1 Laser TransceiversDeclaration of Conformity Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Index TroubleshootingAppendix a Specifications Tables Xiv Who Should Use This Guide How to Use This GuideRelated Documents For information about Refer toCommonly Used Acronyms Document ConventionsGetting Help Getting Help Xviii About This Guide Overview IntroductionFeatures Standalone or Rack Mountable Chassis Fan Management PoE Power over Ethernet SupportPowered Device Classifications PDs Features Features Introduction Installation Shipped With the Switch Unpacking the G-Series SwitchRequired and Shipped Separately Optional Enterasys ComponentsG3G124-24 Optional PoE Module Installation Considerations Order of Installation StepsMounting the Switch Installing the Switch into a Rack Placing the Switch on a Flat SurfacePower Supply Redundancy Power Supply Installation ConsiderationsSupported Power Configurations Power Distribution Upon Power Supply Removal or Addition Allocation of PoE Power to ModulesManagement of PoE Power to PDs Installing a Power SupplyPower supply Power supply handle Captive screws Removing a Power SupplyInstalling an Optional PoE Module on the G3G-24TX IOM Installing and Removing an IOMInstalling a PoE module in the G3G-24TX IOM Installing an IOMIOM handle IOM Initialization BehaviorIOM slot Removing an IOM Connecting Power to the SwitchConnecting to the RJ45 Console Port Connecting to the Console PortPower LED Displays Display StatusConsole Port Pinout Signal RJ45 Pin DB9 PinRJ45 to DB9 Adapter Pinout Pin ConnectionConnecting UTP Cables to RJ45 Ports Connecting to the NetworkConnecting to the USB Console Port Connecting a UTP Cable Segment to RJ45 Port TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Transceiver Type Switch or IOM Ports Installing Optional SFP/XFPConnecting to the Network Removing an XFP/SFP Connecting Fiber-Optic Cables to SFP/XFP PortsCompleting the Installation Removing the Switch Cover Installing an Optional PoE Module in the G3G124-24 SwitchInstalling the PoE Module Troubleshooting Checking the LEDs IOM power off status LEDs Slot 2, 3System LED Definitions Display StatusFixed and IOM Port LEDs Power LEDsIOM Status LEDs Locating the Password Reset button Using the Password Reset ButtonRemoving the Switch from a Rack Removing the Switch from a Rack Troubleshooting Table A-1 G3 Switch Specifications Switch SpecificationsSpecification G3G124-24 and G3G124-24PProcessors/Memory Power SpecificationsPerformance PhysicalIOM Specifications Power Supply SpecificationsTable A-2 Power Supply Specifications Table A-3 G3G-24TX IOM SpecificationsG3G-24SFP Table A-4 G3G-24SFP IOM SpecificationsG3K-2XFP and G3K-4XFP Table A-5 G3K-2XFP and G3K-4XFP IOM SpecificationsTable A-6 G3G-POE Specifications PoE Daughter Card SpecificationsTorque Values Table A-7 Recommended Torque Values by Screw SizeTable A-8 Mini-GBIC Input/Output Port Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXTable A-9 MGBIC-LC01/MGBIC-MT01 Optical Specifications Table A-10 MGBIC-LC01/MGBIC-MT01 Operating RangeMGBIC-LC04 Specifications 100BASE-FX MGBIC-02 Specifications 1000BASE-TMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC07 Specifications 1000BASE-ELX MGBIC-LC05 Specifications 100BASE-FXMGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELXTable A-24 XFP Specifications Gigabit Ethernet Transceiver XFP SpecificationsTable A-25 Recommended Cable Types and Specifications Console Port Pinout AssignmentsRegulatory Compliance Standards Regulatory ComplianceTable A-26 Compliance Standards Index Index-2
Related manuals
Manual 59 pages 23.28 Kb