Enterasys Networks G3G124-24 Console Port Pinout, RJ45 to DB9 Adapter Pinout, Pin Connection

Page 41

Connecting to the Console Port

Table 2-2 Console Port Pinout

Pin

Connection

 

 

1

TXD

 

 

2

Unused

 

 

3

Unused

 

 

4

RXD

 

 

5

GND

 

 

6

Unused

 

 

7

Unused

 

 

8

Unused

 

 

To connect to the console port:

1.Connect the RJ45 connector at one end of the cable to the RJ45 console port on the G‐Series switch.

2.Plug the RJ45 connector at the other end of the cable into the RJ45 to DB9 adapter.

3.Connect the RJ45 to DB9 adapter to the serial port on a terminal or a PC running terminal emulation software.

4.Make sure the terminal emulation software is set as follows:

Select the appropriate serial port (COM port 1 or 2).

Set the data rate to 9600 baud.

Set the data format to 8 data bits, 1 stop bit, and no parity.

Set flow control to none.

Set the emulation mode to VT100.

When using HyperTerminal, select Terminal keys, not Windows keys.

5.When you are ready to begin configuring the G‐Series Ethernet switch, use the procedures in Completing the Installation” on page 2‐22 to power on the switch and boot the software. You will perform initial setup by entering CLI commands on the management console.

Table 2-3 RJ45 to DB9 Adapter Pinout

Signal

RJ45 Pin

DB9 Pin

Receive (RX)

 

1

2

 

Transmit (TX)

 

4

3

 

Ground (GRD)

 

5

5

 

 

 

Pins

Pins

 

 

1

8

 

 

5

1

 

 

 

 

RJ45 Connector (Female)

9

6

 

 

DB9

Connector

(Female)

For a description of how to use the CLI and descriptions of all the CLI commands, refer to the Enterasys G‐Series CLI Reference.

Enterasys G-Series Hardware Installation Guide 2-15

Image 41
Contents Enterasys G-Series Page Page Regulatory Compliance Information AS/NZS Cispr Supplement to Product Instructions Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety Information Class 1 Laser TransceiversDeclaration of Conformity Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Index TroubleshootingAppendix a Specifications Tables Xiv Who Should Use This Guide How to Use This GuideRelated Documents For information about Refer toCommonly Used Acronyms Document ConventionsGetting Help Getting Help Xviii About This Guide Overview IntroductionFeatures Standalone or Rack Mountable Chassis Fan Management PoE Power over Ethernet SupportPowered Device Classifications PDs Features Features Introduction Installation Shipped With the Switch Unpacking the G-Series SwitchRequired and Shipped Separately Optional Enterasys ComponentsG3G124-24 Optional PoE Module Installation Considerations Order of Installation StepsMounting the Switch Installing the Switch into a Rack Placing the Switch on a Flat SurfacePower Supply Redundancy Power Supply Installation ConsiderationsSupported Power Configurations Power Distribution Upon Power Supply Removal or Addition Allocation of PoE Power to ModulesManagement of PoE Power to PDs Installing a Power SupplyPower supply Power supply handle Captive screws Removing a Power SupplyInstalling an Optional PoE Module on the G3G-24TX IOM Installing and Removing an IOMInstalling a PoE module in the G3G-24TX IOM Installing an IOMIOM handle IOM Initialization BehaviorIOM slot Removing an IOM Connecting Power to the SwitchConnecting to the RJ45 Console Port Connecting to the Console PortPower LED Displays Display StatusConsole Port Pinout Signal RJ45 Pin DB9 PinRJ45 to DB9 Adapter Pinout Pin ConnectionConnecting UTP Cables to RJ45 Ports Connecting to the NetworkConnecting to the USB Console Port Connecting a UTP Cable Segment to RJ45 Port TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Transceiver Type Switch or IOM Ports Installing Optional SFP/XFPConnecting to the Network Removing an XFP/SFP Connecting Fiber-Optic Cables to SFP/XFP PortsCompleting the Installation Removing the Switch Cover Installing an Optional PoE Module in the G3G124-24 SwitchInstalling the PoE Module Troubleshooting Checking the LEDs IOM power off status LEDs Slot 2, 3System LED Definitions Display StatusFixed and IOM Port LEDs Power LEDsIOM Status LEDs Locating the Password Reset button Using the Password Reset ButtonRemoving the Switch from a Rack Removing the Switch from a Rack Troubleshooting Table A-1 G3 Switch Specifications Switch SpecificationsSpecification G3G124-24 and G3G124-24PProcessors/Memory Power SpecificationsPerformance PhysicalIOM Specifications Power Supply SpecificationsTable A-2 Power Supply Specifications Table A-3 G3G-24TX IOM SpecificationsG3G-24SFP Table A-4 G3G-24SFP IOM SpecificationsG3K-2XFP and G3K-4XFP Table A-5 G3K-2XFP and G3K-4XFP IOM SpecificationsTable A-6 G3G-POE Specifications PoE Daughter Card SpecificationsTorque Values Table A-7 Recommended Torque Values by Screw SizeTable A-8 Mini-GBIC Input/Output Port Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXTable A-9 MGBIC-LC01/MGBIC-MT01 Optical Specifications Table A-10 MGBIC-LC01/MGBIC-MT01 Operating RangeMGBIC-LC04 Specifications 100BASE-FX MGBIC-02 Specifications 1000BASE-TMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC07 Specifications 1000BASE-ELX MGBIC-LC05 Specifications 100BASE-FXMGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELXTable A-24 XFP Specifications Gigabit Ethernet Transceiver XFP SpecificationsTable A-25 Recommended Cable Types and Specifications Console Port Pinout AssignmentsRegulatory Compliance Standards Regulatory ComplianceTable A-26 Compliance Standards Index Index-2
Related manuals
Manual 59 pages 23.28 Kb