Enterasys Networks G3G124P-24, G3G170-24 manual Connecting Power to the Switch, Removing an IOM

Page 39

Connecting Power to the Switch

When you install an IOM into a slot that previously had an IOM installed, then:

If the IOM being installed is the same type as the previous IOM, the old configuration will be applied to the ports on the new IOM.

If the IOM being installed is not the same type as the previous IOM, the default configuration will be applied to the ports.

For more information about the default configuration, see the Enterasys G‐Series CLI Reference Guide.

Removing an IOM

Caution: Do not attempt to remove an IOM from the G-Series switch when power is on to the switch without performing the following procedure.

Precaución: No intente retirar el módulo IOM del switch G Series si éste está encendido. Antes de hacerlo, debe realizar el siguiente procedimiento.

To remove an installed IOM:

1.Disconnect any cabling from the IOM.

2.Press and hold the POWER OFF button corresponding to the slot from which you are removing the IOM for five seconds. The slot’s status LED flashes green. Refer to Figure 3‐1 on page 3‐2 for the location of the POWER OFF button.

3.When the slot’s status LED turns amber, it is safe to remove the IOM. Loosen the IOM’s two captive screws and gently slide the IOM out of the slot using the IOM’s handle. For more information, refer to IOM Status LEDs” on page 3‐3.

Caution: Use caution when removing an IOM on which you have optional PoE installed to avoid damaging the PoE module.

Precaución: Tenga cuidado al retirar un IOM que tenga un módulo PoE instalado, ya que éste puede dañarse.

4.Replace the coverplate to the slot by tightening the coverplate’s captive screws.

The ports associated with the removed IOM continue to show up when displaying port status, indicating a configuration exists for these ports, but they are in “detached” state.

Connecting Power to the Switch

You can install a single primary source of power or provide two sources of power for redundancy, as described in the following sections. Examples below illustrate connecting two power sources and assume two power supply modules have already been installed as described previously in Installing a Power Supply” on page 2‐8.

Note: The two power supplies in the G-Series have automatic voltage sensing that allows connection to power sources ranging from 100–125 Vac, 12 A or 200–240 Vac, 7A, 50/60 Hz.

To connect the G‐Series switch to one or two power sources, proceed as follows:

1.Plug an appropriate power cord into each switch AC power receptacle as follows:

G3‐PWR‐POE accepts an IEC320 C19 (20A) power cord.

G3‐PWR accepts an IEC320 C13 (15A) power cord.

Enterasys G-Series Hardware Installation Guide 2-13

Image 39
Contents Enterasys G-Series Page Page Regulatory Compliance Information AS/NZS Cispr Supplement to Product Instructions Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety Information Class 1 Laser TransceiversDeclaration of Conformity Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Troubleshooting Appendix a SpecificationsIndex Tables Xiv For information about Refer to How to Use This GuideWho Should Use This Guide Related DocumentsCommonly Used Acronyms Document ConventionsGetting Help Getting Help Xviii About This Guide Overview IntroductionFeatures Standalone or Rack Mountable Chassis PoE Power over Ethernet Support Powered Device Classifications PDsFan Management Features Features Introduction Installation Optional Enterasys Components Unpacking the G-Series SwitchShipped With the Switch Required and Shipped SeparatelyOrder of Installation Steps Mounting the SwitchG3G124-24 Optional PoE Module Installation Considerations Installing the Switch into a Rack Placing the Switch on a Flat SurfacePower Supply Redundancy Power Supply Installation ConsiderationsSupported Power Configurations Power Distribution Upon Power Supply Removal or Addition Allocation of PoE Power to ModulesManagement of PoE Power to PDs Installing a Power SupplyPower supply Power supply handle Captive screws Removing a Power SupplyInstalling an Optional PoE Module on the G3G-24TX IOM Installing and Removing an IOMInstalling a PoE module in the G3G-24TX IOM Installing an IOMIOM Initialization Behavior IOM slotIOM handle Removing an IOM Connecting Power to the SwitchDisplay Status Connecting to the Console PortConnecting to the RJ45 Console Port Power LED DisplaysPin Connection Signal RJ45 Pin DB9 PinConsole Port Pinout RJ45 to DB9 Adapter PinoutConnecting to the Network Connecting to the USB Console PortConnecting UTP Cables to RJ45 Ports Connecting a UTP Cable Segment to RJ45 Port TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Transceiver Type Switch or IOM Ports Installing Optional SFP/XFPConnecting to the Network Removing an XFP/SFP Connecting Fiber-Optic Cables to SFP/XFP PortsCompleting the Installation Removing the Switch Cover Installing an Optional PoE Module in the G3G124-24 SwitchInstalling the PoE Module Troubleshooting Display Status IOM power off status LEDs Slot 2, 3Checking the LEDs System LED DefinitionsPower LEDs IOM Status LEDsFixed and IOM Port LEDs Locating the Password Reset button Using the Password Reset ButtonRemoving the Switch from a Rack Removing the Switch from a Rack Troubleshooting G3G124-24 and G3G124-24P Switch SpecificationsTable A-1 G3 Switch Specifications SpecificationPhysical Power SpecificationsProcessors/Memory PerformanceTable A-3 G3G-24TX IOM Specifications Power Supply SpecificationsIOM Specifications Table A-2 Power Supply SpecificationsG3G-24SFP Table A-4 G3G-24SFP IOM SpecificationsG3K-2XFP and G3K-4XFP Table A-5 G3K-2XFP and G3K-4XFP IOM SpecificationsTable A-7 Recommended Torque Values by Screw Size PoE Daughter Card SpecificationsTable A-6 G3G-POE Specifications Torque ValuesTable A-10 MGBIC-LC01/MGBIC-MT01 Operating Range MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXTable A-8 Mini-GBIC Input/Output Port Specifications Table A-9 MGBIC-LC01/MGBIC-MT01 Optical SpecificationsMGBIC-02 Specifications 1000BASE-T MGBIC-LC03 Specifications 1000BASE-SXMGBIC-LC04 Specifications 100BASE-FX MGBIC-LC07 Specifications 1000BASE-ELX MGBIC-LC05 Specifications 100BASE-FXMGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELXConsole Port Pinout Assignments Gigabit Ethernet Transceiver XFP SpecificationsTable A-24 XFP Specifications Table A-25 Recommended Cable Types and SpecificationsRegulatory Compliance Table A-26 Compliance StandardsRegulatory Compliance Standards Index Index-2
Related manuals
Manual 59 pages 23.28 Kb