Enterasys Networks G3G170-24, G3G124-24P manual

Page 3

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

Notice

Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made.

The hardware, firmware, or software described in this document is subject to change without notice.

IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES.

Enterasys Networks, Inc.

50 Minuteman Road

Andover, MA 01810

©2008 Enterasys Networks, Inc. All rights reserved. Part Number: 9034357‐02 April 2008

ENTERASYS, ENTERASYS NETWORKS, ENTERASYS MATRIX, ENTERASYS NETSIGHT, LANVIEW, WEBVIEW, and any logos associated therewith, are trademarks or registered trademarks of Enterasys Networks, Inc., in the United States and other countries.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

Documentation URL: http://www.enterasys.com/support/manuals

Documentacion URL: http://www.enterasys.com/support/manuals

Dokumentation im Internet: http://www.enterasys.com/support/manuals

i

Image 3
Contents Enterasys G-Series Page Page Class a ITE Notice Clase A. Aviso de ITE Product SafetyFederal Communications Commission FCC Notice Industry Canada NoticeHazardous Substances Electromagnetic Compatibility EMCCompatibilidad Electromágnetica EMC Elektro- magnetische Kompatibilität EMCSupplement to Product Instructions Safety Information Class 1 Laser Transceivers Vcci NoticeBsmi EMC Statement Taiwan USA Declaration of ConformityVii Viii Contents Appendix a Specifications Index Xii Related Documents How to Use This GuideAbout This Guide Who Should Use This GuideCommonly Used Acronyms Document ConventionsGetting Help Getting Help Xvi About This Guide Overview IntroductionFeatures Standalone or Rack Mountable Chassis PoE Power over Ethernet SupportFan Management Powered Device Classifications PDsFor information about Refer to InstallationOptional Enterasys Components Unpacking the G-Series SwitchShipped With the Switch Required and Shipped SeparatelyOrder of Installation Steps Mounting the SwitchG3G124-24 Optional PoE Module Installation Considerations Installing the Switch into a Rack Placing the Switch on a Flat SurfaceInstalling and Removing a Power Supply Power Supply Removal Power Supply PlanningPower Supply Addition or IOM Removal Installing a Power SupplyPower supply Power supply handle Captive screws Removing a Power SupplyInstalling an Optional PoE Module on the G3G-24TX Installing and Removing an IOMFastening screws IOM connector PoE daughter card module Installing an IOMRemoving an IOM IOM slotIOM handle IOM module Display Status Connecting Power to the SwitchPin Connection Connecting to the Console PortConnecting to the RJ45 Console Port Console Port PinoutSignal RJ45 Pin DB9 Pin Connecting to the NetworkConnecting to the USB Console Port Connecting UTP Cables to RJ45 PortsConnecting a UTP Cable Segment to RJ45 Port Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX Installing Optional SFP/XFP Connecting to the Network Removing an XFP/SFP Connecting Fiber-Optic Cables to SFP/XFP PortsCompleting the Installation Removing the Switch Cover Installing an Optional PoE Module in the G3G124-24 SwitchInstalling the PoE Module Troubleshooting Checking the LEDs System LED DefinitionsDisplay Status Power LEDs IOM Status LEDsFixed and IOM Port LEDs Removing the Switch from a Rack Using the Reset ButtonSpecification SpecificationsSwitch Specifications Table A-1 G3 Switch SpecificationsPerformance Power SpecificationsG3G170-24 Processors/MemoryG3G-24TX IOM Module SpecificationsTable A-2 G3G-24TX IOM Specifications Table A-3 G3G-24SFP IOM SpecificationsG3K-2TX and G3K-4TX Table A-4 G3K-2TX and G3K-4TX IOM SpecificationsScrew Size Torque in Pounds Bit Size Table A-6 Mini-GBIC Input/Output Port SpecificationsTorque Values Table A-5 Recommended Torque Values by Screw SizeTable A-9 MGBIC-02 Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-02 Specifications 1000BASE-T Table A-7 MGBIC-LC01/MGBIC-MT01 Optical SpecificationsTable A-11 MGBIC-LC03 Operating Range MGBIC-LC03 Specifications 1000BASE-SXMGBIC-LC04 Specifications 100BASE-FX Table A-10 MGBIC-LC03 Optical SpecificationsMGBIC-LC07 Specifications 1000BASE-ELX MGBIC-LC05 Specifications 100BASE-FXGigabit Ethernet Transceiver XFP Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-LC09 Specifications 1000BASE-LX Regulatory Compliance Table A-22 XFP Fiber-Optic SpecificationsTable A-23 Recommended Cable Types and Specifications Console Port Pinout AssignmentsNumerics Index
Related manuals
Manual 70 pages 46.57 Kb