Enterasys Networks G3G124-24P, G3G170-24 manual Connecting to the Network

Page 40

Connecting to the Network

Caution: Carefully follow the instructions in this manual to avoid damaging the SFP/XFP and G-Series.

The SFP/XFP and G-Series are sensitive to static discharges. Use an antistatic wrist strap and observe all static precautions during this procedure. Failure to do so could result in damage to the SFP/XFP and G-Series. Always leave the SFP/XFP in the antistatic bag or an equivalent antistatic container when not installed.

Precaución: Siga las instrucciones del manual para no dañar el SFP/XFP ni del aparato, puesto que son muy sensible a las descargas de electricidad estática. Utilice la pulsera antiestática y tome todas las precauciones necesarias durante este procedimiento. Si no lo hace, podría dañar el SFP/ XFP o del aparato. Mientras no esté instalado, mantenga el SFP/XFP en su bolsa antiestática o en cualquier otro recipiente antiestático.

To install a SFP/XFP, refer to Figure 2‐10 and proceed as follows.

1.With an antistatic wrist strap attached to your wrist, remove the transceiver from its packaging. If there is a protective dust cover in the transceiver connector, do not remove it at this time.

2.Hold the transceiver so that the connector will seat properly.

3.Carefully align the transceiver with the port slot as shown in Figure 2‐10.

4.Push the transceiver into the port slot until it “clicks” and locks into place.

Figure 2-10 Installing an SFP/XFP (shown with LC connector and without dust cover)

1

Release tab

4

Edge connector (insertion side)

2

Wire handle

5

Port slot

3

Transceiver top side

6

Transceiver side view

2-18 Installation

Image 40
Contents Enterasys G-Series Page Page Product Safety Federal Communications Commission FCC NoticeIndustry Canada Notice Class a ITE Notice Clase A. Aviso de ITEElectromagnetic Compatibility EMC Compatibilidad Electromágnetica EMCElektro- magnetische Kompatibilität EMC Hazardous SubstancesSupplement to Product Instructions Vcci Notice Safety Information Class 1 Laser TransceiversBsmi EMC Statement Taiwan Declaration of Conformity USAVii Viii Contents Appendix a Specifications Index Xii How to Use This Guide About This GuideWho Should Use This Guide Related DocumentsDocument Conventions Commonly Used AcronymsGetting Help Getting Help Xvi About This Guide Introduction OverviewFeatures PoE Power over Ethernet Support Standalone or Rack Mountable ChassisPowered Device Classifications PDs Fan ManagementInstallation For information about Refer toUnpacking the G-Series Switch Shipped With the SwitchRequired and Shipped Separately Optional Enterasys ComponentsMounting the Switch Order of Installation StepsG3G124-24 Optional PoE Module Installation Considerations Placing the Switch on a Flat Surface Installing the Switch into a RackInstalling and Removing a Power Supply Power Supply Planning Power Supply RemovalInstalling a Power Supply Power Supply Addition or IOM RemovalRemoving a Power Supply Power supply Power supply handle Captive screwsInstalling and Removing an IOM Installing an Optional PoE Module on the G3G-24TXInstalling an IOM Fastening screws IOM connector PoE daughter card moduleIOM slot Removing an IOMIOM handle IOM module Connecting Power to the Switch Display StatusConnecting to the Console Port Connecting to the RJ45 Console PortConsole Port Pinout Pin ConnectionConnecting to the Network Connecting to the USB Console PortConnecting UTP Cables to RJ45 Ports Signal RJ45 Pin DB9 PinConnecting a UTP Cable Segment to RJ45 Port Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX Installing Optional SFP/XFP Connecting to the Network Connecting Fiber-Optic Cables to SFP/XFP Ports Removing an XFP/SFPCompleting the Installation Installing an Optional PoE Module in the G3G124-24 Switch Removing the Switch CoverInstalling the PoE Module Troubleshooting System LED Definitions Checking the LEDsDisplay Status IOM Status LEDs Power LEDsFixed and IOM Port LEDs Using the Reset Button Removing the Switch from a RackSpecifications Switch SpecificationsTable A-1 G3 Switch Specifications SpecificationPower Specifications G3G170-24Processors/Memory PerformanceIOM Module Specifications Table A-2 G3G-24TX IOM SpecificationsTable A-3 G3G-24SFP IOM Specifications G3G-24TXTable A-4 G3K-2TX and G3K-4TX IOM Specifications G3K-2TX and G3K-4TXTable A-6 Mini-GBIC Input/Output Port Specifications Torque ValuesTable A-5 Recommended Torque Values by Screw Size Screw Size Torque in Pounds Bit SizeMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX MGBIC-02 Specifications 1000BASE-TTable A-7 MGBIC-LC01/MGBIC-MT01 Optical Specifications Table A-9 MGBIC-02 SpecificationsMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC04 Specifications 100BASE-FXTable A-10 MGBIC-LC03 Optical Specifications Table A-11 MGBIC-LC03 Operating RangeMGBIC-LC05 Specifications 100BASE-FX MGBIC-LC07 Specifications 1000BASE-ELXMGBIC-08 Specifications 1000BASE-ELX Gigabit Ethernet Transceiver XFP SpecificationsMGBIC-LC09 Specifications 1000BASE-LX Table A-22 XFP Fiber-Optic Specifications Table A-23 Recommended Cable Types and SpecificationsConsole Port Pinout Assignments Regulatory ComplianceIndex Numerics
Related manuals
Manual 70 pages 46.57 Kb