Enterasys Networks G3G124-24P manual Installing an Optional PoE Module in the G3G124-24 Switch

Page 43

Installing an Optional PoE Module in the G3G124-24 Switch

c.For details on how to configure the G‐Series using the command line interface, refer to the Enterasys G‐Series CLI Reference . The CLI commands enable you to set a new password and perform more involved management configurations on the G‐Series.

Note: It is strongly recommended that you change the admin password from its default state of blank (no password), once the G-Series switch becomes operational in your network. For more information, refer to the Enterasys G-Series CLI Reference .

If you require assistance, contact Enterasys Networks using one of the methods described in “Getting Help” on page xv.

Installing an Optional PoE Module in the G3G124-24 Switch

Installing PoE capability in the G3G124‐24 base switch requires significant disassembly of the switch. Before installing the PoE module, you must complete the following steps:

1.Unplug all power and network connections to the switch.

2.Remove IOM module(s). Refer to “Removing an IOM” on page 2‐11.

3.Remove power supplies. Refer to “Removing a Power Supply” on page 2‐8.

4.Remove and retain screws securing the switch cover top and compact flash coverplate and remove the switch cover. Refer to “Removing the Switch Cover” on page 2‐21.

Note: Instructions for installing PoE on the base switch do not apply to the G3G124-24P model since it is already equipped with a PoE card.

Removing the Switch Cover

If you have purchased an optional PoE module (G3G‐POE), have unplugged all network and power connections and removed power supplies, you must remove the switch cover as follows to access the PoE board connectors in the G‐Series base chassis.

Caution: Be sure to retain all screws removed from the G-Series switch cover in a secure location to avoid misplacing them. Leaving any loose screws inside the switch could result in severe damage to switch components.

Precaución: Asegúrese de colocar todos los tornillos que haya retirado de la cubierta del switch G- Series en un lugar seguro, para evitar perderlos. Cualquier tornillo suelto que se deje en el interior del switch podría dañar sus componentes.

1.Refer to Figure 2‐12 to locate all screws necessary for removing the cover.

Enterasys G-Series Hardware Installation Guide 2-21

Image 43
Contents Enterasys G-Series Page Page Class a ITE Notice Clase A. Aviso de ITE Product SafetyFederal Communications Commission FCC Notice Industry Canada NoticeHazardous Substances Electromagnetic Compatibility EMCCompatibilidad Electromágnetica EMC Elektro- magnetische Kompatibilität EMCSupplement to Product Instructions Vcci Notice Safety Information Class 1 Laser TransceiversBsmi EMC Statement Taiwan USA Declaration of ConformityVii Viii Contents Appendix a Specifications Index Xii Related Documents How to Use This GuideAbout This Guide Who Should Use This GuideCommonly Used Acronyms Document ConventionsGetting Help Getting Help Xvi About This Guide Overview IntroductionFeatures Standalone or Rack Mountable Chassis PoE Power over Ethernet SupportFan Management Powered Device Classifications PDsFor information about Refer to InstallationOptional Enterasys Components Unpacking the G-Series SwitchShipped With the Switch Required and Shipped SeparatelyMounting the Switch Order of Installation StepsG3G124-24 Optional PoE Module Installation Considerations Installing the Switch into a Rack Placing the Switch on a Flat SurfaceInstalling and Removing a Power Supply Power Supply Removal Power Supply PlanningPower Supply Addition or IOM Removal Installing a Power SupplyPower supply Power supply handle Captive screws Removing a Power SupplyInstalling an Optional PoE Module on the G3G-24TX Installing and Removing an IOMFastening screws IOM connector PoE daughter card module Installing an IOMIOM slot Removing an IOMIOM handle IOM module Display Status Connecting Power to the SwitchPin Connection Connecting to the Console PortConnecting to the RJ45 Console Port Console Port PinoutSignal RJ45 Pin DB9 Pin Connecting to the NetworkConnecting to the USB Console Port Connecting UTP Cables to RJ45 PortsConnecting a UTP Cable Segment to RJ45 Port Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX Installing Optional SFP/XFP Connecting to the Network Removing an XFP/SFP Connecting Fiber-Optic Cables to SFP/XFP PortsCompleting the Installation Removing the Switch Cover Installing an Optional PoE Module in the G3G124-24 SwitchInstalling the PoE Module Troubleshooting System LED Definitions Checking the LEDsDisplay Status IOM Status LEDs Power LEDsFixed and IOM Port LEDs Removing the Switch from a Rack Using the Reset ButtonSpecification SpecificationsSwitch Specifications Table A-1 G3 Switch SpecificationsPerformance Power SpecificationsG3G170-24 Processors/MemoryG3G-24TX IOM Module SpecificationsTable A-2 G3G-24TX IOM Specifications Table A-3 G3G-24SFP IOM SpecificationsG3K-2TX and G3K-4TX Table A-4 G3K-2TX and G3K-4TX IOM SpecificationsScrew Size Torque in Pounds Bit Size Table A-6 Mini-GBIC Input/Output Port SpecificationsTorque Values Table A-5 Recommended Torque Values by Screw SizeTable A-9 MGBIC-02 Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-02 Specifications 1000BASE-T Table A-7 MGBIC-LC01/MGBIC-MT01 Optical SpecificationsTable A-11 MGBIC-LC03 Operating Range MGBIC-LC03 Specifications 1000BASE-SXMGBIC-LC04 Specifications 100BASE-FX Table A-10 MGBIC-LC03 Optical SpecificationsMGBIC-LC07 Specifications 1000BASE-ELX MGBIC-LC05 Specifications 100BASE-FXMGBIC-08 Specifications 1000BASE-ELX Gigabit Ethernet Transceiver XFP SpecificationsMGBIC-LC09 Specifications 1000BASE-LX Regulatory Compliance Table A-22 XFP Fiber-Optic SpecificationsTable A-23 Recommended Cable Types and Specifications Console Port Pinout AssignmentsNumerics Index
Related manuals
Manual 70 pages 46.57 Kb