Enterasys Networks A2H124-24FX manual Contents

Page 13

 

Contents

About This Guide

 

Who Should Use This Guide

xv

How to Use This Guide

xvi

Related Documents

xvi

Conventions Used in This Guide

xvii

Chapter 1: Introduction

 

Overview

1-2

A2H124-24FX

1-2

Stack Connections

1-3

Redundant Power Supply Capability

1-3

Connectivity

1-4

Management

1-5

Switch Configuration Using WebView

1-5

Switch Configuration Using CLI Commands

1-5

Standards Compatibility

1-5

LANVIEW Diagnostic LEDs

1-5

Getting Help

1-6

Chapter 2: Network Requirements

 

100BASE-FX Multimode Fiber-Optic Network

2-1

1000BASE-FXFiber-Optic Network

2-2

1000BASE-T Twisted Pair Gigabit Ethernet Network

2-2

Chapter 3: Hardware Installation

 

Considerations Prior to Installation

3-2

Required Tools

3-2

Unpacking the Switch

3-2

Installing Optional Mini-GBICs

3-3

Removing the Mini-GBIC

3-6

Installing the Switch on a Flat Surface

3-7

Installing the Rubber Feet

3-7

Guidelines for Flat Surface Installation

3-8

Rack Mounting the Switch

3-10

Guidelines for Rackmount Installation

3-10

Attaching Brackets and Installing in Rack

3-10

Connecting Stacking Cables

3-11

Configuring Switches in a Stack

3-13

About SecureStack A2 Switch Operation in a Stack

3-13

Recommended Procedures for New and Existing Stacks

3-14

xi

Image 13
Contents SecureStack A2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Page Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv Who Should Use This Guide About This GuideRelated Documents How to Use This GuideFollowing conventions are used in this guide Conventions Used in This GuideConventions Used in This Guide Xviii About This Guide Introduction A2H124-24FX OverviewStack Connections Redundant Power Supply CapabilityDescription of Mini-GBICs ConnectivitySwitch Configuration Using WebView Lanview Diagnostic LEDsSwitch Configuration Using CLI Commands ManagementSupport@enterasys.com Getting Help100BASE-FX Multimode Fiber-Optic Network Network Requirements1000BASE-T Twisted Pair Gigabit Ethernet Network 1000BASE-FX Fiber-Optic NetworkHardware Installation Unpacking the Switch Considerations Prior to InstallationRequired Tools Preparation Installing Optional Mini-GBICsInstallation Mini-GBIC with MT-RJ Connector Removing the Mini-GBIC Mini-GBIC with LC ConnectorInstalling the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Guidelines for Flat Surface InstallationArea Guidelines for Switch Installation on Flat Surface Guidelines for Rackmount Installation Rack Mounting the SwitchAttaching Brackets and Installing in Rack Attaching the Rackmount Brackets Connecting Stacking CablesStacking Cable Connections About SecureStack A2 Switch Operation in a Stack Configuring Switches in a StackInstalling a New Stackable System of Up to Eight Switches Recommended Procedures for New and Existing StacksImportant Considerations About Using Clear Config in a Stack AC Power Connecting AC and RPS-SYS PowerSwitch Rear View RPS coverplate Screw holes for coverplate C2RPS-SYS Redundant Power SystemStack Initialization Overview What Is Needed Connecting to Console Port for Local ManagementDB9 female connector Serial interface cable Connecting to an IBM or Compatible Device13 Connecting a VT Series Terminal Connecting to a VT Series Terminal14 Connecting to a Modem Connecting to a ModemConnecting to the Network 15 Connecting a Fiber-Optic Cable Segment to MT-RJ Port Connecting Fiber-Optic Cables to MT-RJ Mini-GBIC Ports SecureStack A2 Installation Guide Connecting Fiber-Optic Cables to LC Mini-GBIC Ports Connecting to the Network Connecting UTP Cables to RJ45 Mini-GBIC Ports 16 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Initial Logon to Switch Management Completing the InstallationCompleting the Installation Hardware Installation Troubleshooting Lanview LEDs of A2H124-24FX Using LanviewLED Down RPS Configuration Guide for proper setup Troubleshooting ChecklistConfiguration Guide for the IP address Refer to the SecureStack A2 Reset Password Switch Using the Reset Password SwitchUsing the Reset Password Switch Troubleshooting Specifications Table A-1 A2H124-24FX Switch Specifications Switch SpecificationsTable A-1 A2H124-24FX Switch Specifications Environmental Mini-GBIC Input/Output SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Gigabit Ethernet SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXMGBIC-02 Specifications 1000BASE-T MGBIC-08 Specifications 1000BASE-ELXRegulatory Compliance Console Port Pinout AssignmentsRegulatory Compliance Specifications Index Index-2

A2H124-24FX specifications

Enterasys Networks A2H124-24FX is a high-performance network switch designed to meet the demands of modern data centers and enterprise environments. This switch exemplifies the blend of reliability, scalability, and advanced features that enterprises require to ensure seamless connectivity and data management.

One of the main features of the A2H124-24FX is its 24 Fast Ethernet (10/100) ports. These ports provide a robust foundation for connecting various devices within a network, making it ideal for workplaces that require extensive connectivity options. Additionally, the switch supports up to 4 Gigabit SFP (Small Form-factor Pluggable) uplink ports, which facilitate high-speed connections to backbone switches or routers, catering to bandwidth-intensive applications.

Another significant characteristic of the A2H124-24FX is its support for Power over Ethernet (PoE). This technology enables the switch to deliver power to connected devices such as IP phones, wireless access points, and security cameras through the same Ethernet cable that transmits data. This feature not only reduces the need for additional power supplies but also streamlines installation processes, reducing overall operational costs.

Security is a paramount concern for any enterprise network, and the A2H124-24FX addresses this through various advanced security features. It includes support for IEEE 802.1X Network Access Control, which ensures that only authenticated users can access the network. Additionally, it provides features such as MAC address filtering and VLAN support to segment network traffic and enhance overall security.

In terms of management, the Enterasys Networks A2H124-24FX is equipped with a user-friendly interface that allows network administrators to configure and monitor the switch effortlessly. It supports both CLI (Command Line Interface) and web-based management, providing flexibility depending on user preference.

This switch also supports advanced Layer 2 and Layer 3 capabilities, including Quality of Service (QoS) features that help prioritize traffic, ensuring that critical applications receive the necessary bandwidth for optimal performance.

In conclusion, the Enterasys Networks A2H124-24FX combines functionality, security, and ease of management, making it an ideal choice for businesses looking to enhance their network infrastructure. Its robust features and reliable performance can effectively support the complex demands of modern networking environments.