Enterasys Networks A2H124-24FX manual MGBIC-08 Specifications 1000BASE-ELX

Page 78

Gigabit Ethernet Specifications

MGBIC-08 Specifications (1000BASE-ELX)

Table A-9 MGBIC-08 Optical Specifications

Item

10 µm SMF

 

 

 

 

 

 

Transmit Power (minimum)

-0 dBm, min.

+2 dBm, typical

+5 dBm, max.

 

 

 

 

Receive Sensitivity

-24 dBm, min.

-26 dBm, typical

 

 

 

 

 

Maximum Input Power

-3 dBm

 

 

 

 

 

 

Link Power Budget1

23 dB

28 dB, typical

 

(Full Duplex Only)

 

 

 

1.The maximum drive distance (up to 70 km) depends on the quality of the installed single-mode fiber-optic cable segment. Use the Link Power Budget to calculate the maximum cable length of the attached segment. The Link Power Budget must not exceed those specified in this table. The MGBIC-08 input power must not exceed -3 dBm. Otherwise, saturation could occur.

Table A-10 MGBIC-08 Operating Range

Item

1550 nm

Range

 

 

 

9 or 10 µm SMF

N/A

70,000 Meters

 

 

 

MGBIC-02 Specifications (1000BASE-T)

Table A-11 MGBIC-02 Specifications

Item

Specification

 

 

Supported Cable:

 

Type

Copper, Category 5 UTP

Maximum Length

Up to 100 meters

 

 

Connector

RJ45

 

 

Data Rate

1 Gbps, IEEE 802.3:2000 compatible

 

1000BASE-T operation only

 

Automatic crossover detection

 

 

TX Output impedance

100 ohms, typical at all frequencies between 1 MHz and 125 MHz

 

 

RX Input impedance

100 ohms, typical at all frequencies between 1 MHz and 125 MHz

 

 

A-6 Specifications

Image 78
Contents SecureStack A2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Page Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv About This Guide Who Should Use This GuideHow to Use This Guide Related DocumentsConventions Used in This Guide Following conventions are used in this guideConventions Used in This Guide Xviii About This Guide Introduction Overview A2H124-24FXRedundant Power Supply Capability Stack ConnectionsConnectivity Description of Mini-GBICsSwitch Configuration Using CLI Commands Lanview Diagnostic LEDsSwitch Configuration Using WebView ManagementGetting Help Support@enterasys.comNetwork Requirements 100BASE-FX Multimode Fiber-Optic Network1000BASE-FX Fiber-Optic Network 1000BASE-T Twisted Pair Gigabit Ethernet NetworkHardware Installation Considerations Prior to Installation Unpacking the SwitchRequired Tools Installing Optional Mini-GBICs PreparationInstallation Mini-GBIC with MT-RJ Connector Mini-GBIC with LC Connector Removing the Mini-GBICInstalling the Switch on a Flat Surface Installing the Rubber FeetGuidelines for Flat Surface Installation Chassis Bottom, Rubber Feet PlacementArea Guidelines for Switch Installation on Flat Surface Rack Mounting the Switch Guidelines for Rackmount InstallationAttaching Brackets and Installing in Rack Connecting Stacking Cables Attaching the Rackmount BracketsStacking Cable Connections Configuring Switches in a Stack About SecureStack A2 Switch Operation in a StackRecommended Procedures for New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesImportant Considerations About Using Clear Config in a Stack Connecting AC and RPS-SYS Power AC PowerSwitch Rear View C2RPS-SYS Redundant Power System RPS coverplate Screw holes for coverplateStack Initialization Overview Connecting to Console Port for Local Management What Is NeededConnecting to an IBM or Compatible Device DB9 female connector Serial interface cableConnecting to a VT Series Terminal 13 Connecting a VT Series TerminalConnecting to a Modem 14 Connecting to a ModemConnecting to the Network 15 Connecting a Fiber-Optic Cable Segment to MT-RJ Port Connecting Fiber-Optic Cables to MT-RJ Mini-GBIC Ports SecureStack A2 Installation Guide Connecting Fiber-Optic Cables to LC Mini-GBIC Ports Connecting to the Network Connecting UTP Cables to RJ45 Mini-GBIC Ports 16 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Completing the Installation Initial Logon to Switch ManagementCompleting the Installation Hardware Installation Troubleshooting Using Lanview Lanview LEDs of A2H124-24FXLED Down RPS Troubleshooting Checklist Configuration Guide for proper setupConfiguration Guide for the IP address Refer to the SecureStack A2 Using the Reset Password Switch Reset Password SwitchUsing the Reset Password Switch Troubleshooting Specifications Switch Specifications Table A-1 A2H124-24FX Switch SpecificationsMini-GBIC Input/Output Specifications Table A-1 A2H124-24FX Switch Specifications EnvironmentalGigabit Ethernet Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXMGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-TConsole Port Pinout Assignments Regulatory ComplianceRegulatory Compliance Specifications Index Index-2

A2H124-24FX specifications

Enterasys Networks A2H124-24FX is a high-performance network switch designed to meet the demands of modern data centers and enterprise environments. This switch exemplifies the blend of reliability, scalability, and advanced features that enterprises require to ensure seamless connectivity and data management.

One of the main features of the A2H124-24FX is its 24 Fast Ethernet (10/100) ports. These ports provide a robust foundation for connecting various devices within a network, making it ideal for workplaces that require extensive connectivity options. Additionally, the switch supports up to 4 Gigabit SFP (Small Form-factor Pluggable) uplink ports, which facilitate high-speed connections to backbone switches or routers, catering to bandwidth-intensive applications.

Another significant characteristic of the A2H124-24FX is its support for Power over Ethernet (PoE). This technology enables the switch to deliver power to connected devices such as IP phones, wireless access points, and security cameras through the same Ethernet cable that transmits data. This feature not only reduces the need for additional power supplies but also streamlines installation processes, reducing overall operational costs.

Security is a paramount concern for any enterprise network, and the A2H124-24FX addresses this through various advanced security features. It includes support for IEEE 802.1X Network Access Control, which ensures that only authenticated users can access the network. Additionally, it provides features such as MAC address filtering and VLAN support to segment network traffic and enhance overall security.

In terms of management, the Enterasys Networks A2H124-24FX is equipped with a user-friendly interface that allows network administrators to configure and monitor the switch effortlessly. It supports both CLI (Command Line Interface) and web-based management, providing flexibility depending on user preference.

This switch also supports advanced Layer 2 and Layer 3 capabilities, including Quality of Service (QoS) features that help prioritize traffic, ensuring that critical applications receive the necessary bandwidth for optimal performance.

In conclusion, the Enterasys Networks A2H124-24FX combines functionality, security, and ease of management, making it an ideal choice for businesses looking to enhance their network infrastructure. Its robust features and reliable performance can effectively support the complex demands of modern networking environments.