Enterasys Networks A2H124-24FX manual How to Use This Guide, Related Documents

Page 18

How to Use This Guide

How to Use This Guide

Read through this guide completely to familiarize yourself with its contents and gain an understanding of the features and capabilities of the stackable Ethernet switch. A general knowledge of data communications networks is helpful when setting up the switches.

This preface provides an overview of this guide and the SecureStack A2 manual set, a brief summary of each chapter and defines the conventions used throughout this guide. To locate information concerning various subjects in this guide, refer to the following table:

For...

Refer to...

 

 

An overview of the SecureStack A2 features and

Chapter 1, Introduction

how to obtain technical support

 

 

 

Network requirements that must be met before

Chapter 2, Network Requirements

installing the SecureStack A2

 

 

 

Instructions to install the SecureStack A2 on a flat

Chapter 3, Hardware Installation

surface or in a standard 19-inch rack and

 

configure the SecureStack A2 in a stacked

 

configuration

 

 

 

Troubleshooting installation problems and

Chapter 4, Troubleshooting

diagnosing network/operational problems using

 

the LANVIEW LEDs

 

 

 

Specifications, environmental requirements, and

Appendix A, Specifications

physical properties of the SecureStack A2 and

 

optional Mini-GBICs

 

 

 

Related Documents

The documents listed below provide the necessary information to install and configure the switch and can be obtained from the World Wide Web in Adobe Acrobat Portable Document Format (PDF) at the following site:

http://www.enterasys.com/support/manuals

SecureStack A2 Configuration Guide describes how to use the Command Line Interface (CLI) to set up and manage the A2 switches.

Cabling Guide provides information concerning network cabling, dB loss, and other cabling specifications and usage. Unlike the SecureStack A2 Configuration Guide, the Cabling Guide is not listed alphabetically on the web site. Instead, it is under the Overview Guides link.

xvi About This Guide

Image 18
Contents SecureStack A2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Page Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv About This Guide Who Should Use This GuideHow to Use This Guide Related DocumentsConventions Used in This Guide Following conventions are used in this guideConventions Used in This Guide Xviii About This Guide Introduction Overview A2H124-24FXRedundant Power Supply Capability Stack ConnectionsConnectivity Description of Mini-GBICsSwitch Configuration Using CLI Commands Lanview Diagnostic LEDsSwitch Configuration Using WebView ManagementGetting Help Support@enterasys.comNetwork Requirements 100BASE-FX Multimode Fiber-Optic Network1000BASE-FX Fiber-Optic Network 1000BASE-T Twisted Pair Gigabit Ethernet NetworkHardware Installation Considerations Prior to Installation Unpacking the SwitchRequired Tools Installing Optional Mini-GBICs PreparationInstallation Mini-GBIC with MT-RJ Connector Mini-GBIC with LC Connector Removing the Mini-GBICInstalling the Switch on a Flat Surface Installing the Rubber FeetGuidelines for Flat Surface Installation Chassis Bottom, Rubber Feet PlacementArea Guidelines for Switch Installation on Flat Surface Rack Mounting the Switch Guidelines for Rackmount InstallationAttaching Brackets and Installing in Rack Connecting Stacking Cables Attaching the Rackmount BracketsStacking Cable Connections Configuring Switches in a Stack About SecureStack A2 Switch Operation in a StackRecommended Procedures for New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesImportant Considerations About Using Clear Config in a Stack Connecting AC and RPS-SYS Power AC PowerSwitch Rear View C2RPS-SYS Redundant Power System RPS coverplate Screw holes for coverplateStack Initialization Overview Connecting to Console Port for Local Management What Is NeededConnecting to an IBM or Compatible Device DB9 female connector Serial interface cableConnecting to a VT Series Terminal 13 Connecting a VT Series TerminalConnecting to a Modem 14 Connecting to a ModemConnecting to the Network 15 Connecting a Fiber-Optic Cable Segment to MT-RJ Port Connecting Fiber-Optic Cables to MT-RJ Mini-GBIC Ports SecureStack A2 Installation Guide Connecting Fiber-Optic Cables to LC Mini-GBIC Ports Connecting to the Network Connecting UTP Cables to RJ45 Mini-GBIC Ports 16 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Completing the Installation Initial Logon to Switch ManagementCompleting the Installation Hardware Installation Troubleshooting Using Lanview Lanview LEDs of A2H124-24FXLED Down RPS Troubleshooting Checklist Configuration Guide for proper setupConfiguration Guide for the IP address Refer to the SecureStack A2 Using the Reset Password Switch Reset Password SwitchUsing the Reset Password Switch Troubleshooting Specifications Switch Specifications Table A-1 A2H124-24FX Switch SpecificationsMini-GBIC Input/Output Specifications Table A-1 A2H124-24FX Switch Specifications EnvironmentalGigabit Ethernet Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXMGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-TConsole Port Pinout Assignments Regulatory ComplianceRegulatory Compliance Specifications Index Index-2

A2H124-24FX specifications

Enterasys Networks A2H124-24FX is a high-performance network switch designed to meet the demands of modern data centers and enterprise environments. This switch exemplifies the blend of reliability, scalability, and advanced features that enterprises require to ensure seamless connectivity and data management.

One of the main features of the A2H124-24FX is its 24 Fast Ethernet (10/100) ports. These ports provide a robust foundation for connecting various devices within a network, making it ideal for workplaces that require extensive connectivity options. Additionally, the switch supports up to 4 Gigabit SFP (Small Form-factor Pluggable) uplink ports, which facilitate high-speed connections to backbone switches or routers, catering to bandwidth-intensive applications.

Another significant characteristic of the A2H124-24FX is its support for Power over Ethernet (PoE). This technology enables the switch to deliver power to connected devices such as IP phones, wireless access points, and security cameras through the same Ethernet cable that transmits data. This feature not only reduces the need for additional power supplies but also streamlines installation processes, reducing overall operational costs.

Security is a paramount concern for any enterprise network, and the A2H124-24FX addresses this through various advanced security features. It includes support for IEEE 802.1X Network Access Control, which ensures that only authenticated users can access the network. Additionally, it provides features such as MAC address filtering and VLAN support to segment network traffic and enhance overall security.

In terms of management, the Enterasys Networks A2H124-24FX is equipped with a user-friendly interface that allows network administrators to configure and monitor the switch effortlessly. It supports both CLI (Command Line Interface) and web-based management, providing flexibility depending on user preference.

This switch also supports advanced Layer 2 and Layer 3 capabilities, including Quality of Service (QoS) features that help prioritize traffic, ensuring that critical applications receive the necessary bandwidth for optimal performance.

In conclusion, the Enterasys Networks A2H124-24FX combines functionality, security, and ease of management, making it an ideal choice for businesses looking to enhance their network infrastructure. Its robust features and reliable performance can effectively support the complex demands of modern networking environments.