Compex Systems 802.11N manual FCC Notice

Page 3

FCC NOTICE

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Connect the computer to an outlet on a circuit different from that to which the receiver is connected.

•Increase the separation between the computer and receiver.

•Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.

FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference that may cause undesired operation.

RF Exposure warning

The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.

ICES 003 Statement

This Class B digital apparatus complies with Canadian ICES-003.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Page Trademark Information FCC Notice Declaration of Conformity Table of Contents Status System TabIntroduction Overview the ProductVirtual AP Multiple Ssid Highly Secured Wireless NetworkUConfig Utility Point-to-Point & Point-to-MultiPoint SupportAccess Point WDS Mode Station Mode Point-to-Point Station WDS ModeRouter Mode Repeater WDS Mode Device Panel Views and Descriptions Features Status and IndicationsAntenna Alignment Install the HardwareAntenna Alignment Installation Direction Mount the Unit on a Pole Setup RequirementsPrepare Unit to mount to a pole Page For Windows 95/98/98SE/ME/NT Configure the IP AddressStep Select the Use the following IP address radio button For Windows XP/2000Click on the OK button to close all windows Access with uConfig Access the Web InterfaceStep It then opens the device home page. The Status Access with a Web Browser Step How to save changes NavigationMain Menu Bar LAN Setup Basic Network TabNetwork Modes Bridging and Routing Primary DNS IP optional Basic Wireless Tab Enable the radioBasic Wireless Settings Wireless Mode Country Code Access Point Parameters SettingsWireless Profile Local AP-ESSIDRate Aggressiveness Channel Spectrum WidthChannel Frequency Data RateStation Parameters Settings Remote AP-ESSIDRemote AP Preferred MAC Channel Scan List Wireless Adapter modePreshared Key Wireless SecurityWPA or WPA2 Authentication Cipher TypeAccounting Port Authentication PortPrimary Radius Server IP Secondary Radius Server IPStation, Station WDS, Repeater WDS mode Identity User PasswordUser Name IEEE802.1x Settings IEEE802.1x Key RotationIEEE802.1x Key Length WEP Key Authentication TypeKey Type Current KeyVirtual Access Point VAP Advance Wireless Tab Long Range Parameters SetupLong Range Parameters Noise Immunity Signal Strength Indicator RssiAdvanced Network Tab Spanning Tree Setup NAT SetupAdding an entry from Known Server Adding an entry from Custom Server Bandwidth Control Rule Type select By IP or By MACRouter Info Protocol version select RIPv1 or RIPv2 Firewall Setup Outbound Filtering Setup Page Services Tab Ping Watchdog Auto-RebootWeb Http Security Snmp SetupNTP Setup Engine ID Default isTelnet Access Setup SSH Access SetupSystem Log Setup System Tab Firmware UpgradeRead-Only Username Administrative and Read-only AccountEnable Read-Only Account Host NameDevice Maintenance Configuration ManagementStatus Status ReportingMain LAN Setting WAN SettingRadio Wlan Local AP Statistics Station Connection Status InfoWlan Connected Status Channel WidthPage Appendix I Network Bridge ModeNetwork Mode Selections Bridge Mode Network SettingsBridge IP Address Primary/Secondary DNS IPDhcp Fallback IP Spanning Tree Protocol Bridge mode Firewall Configuration SettingsAP-Router mode Network Settings Appendix II Wireless with Router ModePage Port Forwarding Settings IP of the host system which sends the packets Page Appendix III- Advanced Settings Advanced Wireless SettingRate Aggressiveness Acknowledgement Timeout LED Thresholds Configuration Signal Strength LED SettingsSnmp Agent Appendix IV- ServicesSystem Log NTP Client, Web, Telnet, SSH Server

802.11N specifications

Compex Systems 802.11N solutions are designed to provide high-performance wireless networking, catering to the growing demand for faster and more reliable connectivity in various applications. The 802.11N standard, also known as Wi-Fi 4, significantly enhances the capabilities of previous Wi-Fi standards by utilizing advanced technologies and features.

One of the key characteristics of Compex Systems 802.11N products is their support for Multiple Input Multiple Output (MIMO) technology. MIMO allows the transmission of multiple data streams simultaneously, effectively improving throughput and range. This is especially useful in environments with high user density or physical obstructions, as it enhances the signal quality and minimizes interference.

Another significant feature is the use of Channel Bonding, which combines two adjacent channels to double the data rate. This capability enables users to experience higher speeds, typically reaching up to 600 Mbps under optimal conditions. The dual-band operation, supporting both 2.4 GHz and 5 GHz frequencies, further enhances flexibility and performance. The 2.4 GHz band offers broader coverage, while the 5 GHz band provides faster speeds with less congestion.

Compex Systems also incorporates advanced security protocols in their 802.11N solutions. With support for WPA2 encryption and robust authentication methods, users can ensure that their connections remain secure, protecting sensitive data from potential threats.

Quality of Service (QoS) is another critical feature, allowing network administrators to prioritize traffic according to application needs. This ensures that bandwidth-intensive applications, such as video streaming and online gaming, receive the necessary resources for optimal performance, even in a crowded network environment.

Designed for versatility, Compex Systems 802.11N devices can be employed in various scenarios, including enterprise, education, healthcare, and hospitality sectors. Their compact and durable designs make them suitable for deployment in both indoor and outdoor settings.

Overall, Compex Systems 802.11N solutions offer a comprehensive set of features and technologies aimed at providing robust, high-speed wireless connectivity. With MIMO, Channel Bonding, dual-band support, enhanced security, and QoS capabilities, these systems are well-suited to meet the demands of modern wireless networking environments.
Top Page Image Contents