Compex Systems 802.11N manual Bandwidth Control, Rule Type select By IP or By MAC

Page 50

Bandwidth Control

Bandwidth Control: Default is disabled. Check on box to enable.

This control let user set a max limited bandwidth to router.

This function let use share one high speed broadband line with several routers each limited to a maximum limited by its bandwidth control.

Download Total Rate(kbit) enter the max bandwidth limit for downloading on this router. Upload Total Rate(kbit): enter the max bandwidth limit for uploading on this router.

Upload/Download limit can also be controlled for each user by IP or MAC address. Name: enter short name of user. Name track the user to rule only.

Committed Rate(kbit): enter the average rate for user.

Ceiling Rate (kbit): enter the peak rate allowed for user

Rule Type: select By IP or By MAC

IP/MAC Address: enter the local IP address if rule type is By IP

enter the local PC ethernet MAC address if rule type is By MAC

Routing Information Protocol: Default is disabled. Check on box to enable. For configuration refer to Appendix section.

Router Info Protocol version: select RIPv1 or RIPv2

Image 50

Contents Page Trademark Information FCC Notice Declaration of Conformity Table of Contents System Tab StatusOverview the Product IntroductionPoint-to-Point & Point-to-MultiPoint Support Highly Secured Wireless NetworkUConfig Utility Virtual AP Multiple SsidAccess Point WDS Mode Station Mode Station WDS Mode Point-to-PointRouter Mode Repeater WDS Mode Features Status and Indications Device Panel Views and DescriptionsInstall the Hardware Antenna AlignmentAntenna Alignment Installation Direction Setup Requirements Mount the Unit on a PolePrepare Unit to mount to a pole Page Configure the IP Address For Windows 95/98/98SE/ME/NTStep For Windows XP/2000 Select the Use the following IP address radio buttonClick on the OK button to close all windows Access the Web Interface Access with uConfigStep It then opens the device home page. The Status Access with a Web Browser Step Main Menu Bar How to save changesNavigation Network Modes Bridging and Routing LAN SetupBasic Network Tab Primary DNS IP optional Basic Wireless Settings Basic Wireless TabEnable the radio Wireless Mode Local AP-ESSID Access Point Parameters SettingsWireless Profile Country CodeData Rate Channel Spectrum WidthChannel Frequency Rate AggressivenessRemote AP Preferred MAC Station Parameters SettingsRemote AP-ESSID Wireless Adapter mode Channel Scan ListCipher Type Wireless SecurityWPA or WPA2 Authentication Preshared KeySecondary Radius Server IP Authentication PortPrimary Radius Server IP Accounting PortUser Name Station, Station WDS, Repeater WDS mode IdentityUser Password IEEE802.1x Key Length IEEE802.1x SettingsIEEE802.1x Key Rotation Current Key Authentication TypeKey Type WEP KeyVirtual Access Point VAP Long Range Parameters Advance Wireless TabLong Range Parameters Setup Signal Strength Indicator Rssi Noise Immunity Advanced Network Tab Adding an entry from Known Server Spanning Tree SetupNAT Setup Adding an entry from Custom Server Router Info Protocol version select RIPv1 or RIPv2 Bandwidth ControlRule Type select By IP or By MAC Firewall Setup Outbound Filtering Setup Page Services Tab Auto-Reboot Ping WatchdogEngine ID Default is Snmp SetupNTP Setup Web Http SecuritySystem Log Setup Telnet Access SetupSSH Access Setup Firmware Upgrade System TabHost Name Administrative and Read-only AccountEnable Read-Only Account Read-Only UsernameConfiguration Management Device MaintenanceMain StatusStatus Reporting Radio LAN SettingWAN Setting Channel Width Station Connection Status InfoWlan Connected Status Wlan Local AP StatisticsPage Bridge Mode Network Settings Bridge ModeNetwork Mode Selections Appendix I NetworkDhcp Fallback IP Bridge IP AddressPrimary/Secondary DNS IP Bridge mode Firewall Configuration Settings Spanning Tree ProtocolAppendix II Wireless with Router Mode AP-Router mode Network SettingsPage Port Forwarding Settings IP of the host system which sends the packets Page Rate Aggressiveness Appendix III- Advanced SettingsAdvanced Wireless Setting Acknowledgement Timeout Signal Strength LED Settings LED Thresholds ConfigurationAppendix IV- Services Snmp AgentNTP Client, Web, Telnet, SSH Server System Log