Edimax Technology Edimax user guide Router manual Settings Dynamic DNS

Page 39

Settings – Dynamic DNS

Dynamic DNS

Use this to Enable/Disable the Dynamic DNS feature, and select the required

Service

service provider.

 

Disable – Dynamic DNS is not used.

 

TZO – Select this to use the TZO service (www.tzo.com). You must configure

 

the TZO section of this screen.

 

Standard Client – Select this to use the standard service (from

 

www.dyndns.org or other provider). You must configure the Standard Client

 

section of this screen.

 

3322(in China) – This is available in China. It is similar to “Standard client”

 

User Defined DDNS Server – This is the user define DDNS server. If the

 

DDNS other than TZO, dyndns.org and 3322.

WAN Port

Select the WAN port on which the Dynamic DNS is used.

Binding

The "Force Update" button will update your record on the Dynamic DNS

 

 

Server immediately.

 

 

Additional

These options are available if using the standard client.

Standard

Enable Wildcard – If selected, traffic sent to sub-domains (of your Domain

Client or 3322

name) will also be forwarded to you.

Settings

Enable backup MX – If enabled, you must enter the Mail Exchanger address

 

 

below.

 

Mail Exchanger – If the setting above is enabled, enter the address of the

 

backup Mail Exchanger.

Page 35

Image 39
Contents Load Balancing Router User’s Guide Page Table of Contents Overview TCP/IP Settings Overview General Problems Internet AccessOperation System Status WAN Status NAT Status Introduction Internet FeaturesMultiple IP Address Support Port Switching Hub Other FeaturesPhysical Details Package ContentsLED Action Condition LAN Ports Default SettingsReset Button Rear PanelWindows Tftp utility Overview Basic SetupProcedure Configuring The Load Balancer for your LANNo Response ? Subnet Mask Settings LAN & DhcpConfiguration IP AddressARP Proxy LAN Any IP SetupDhcp IP Address RangeInstallation Diagram Installing The Load Balancer in your LANPrimary Setup Screen Configuring The Load Balancer for Internet AccessSettings Primary Setup Optional Overview Configure PCs on your LANTCP/IP Settings Internet AccessAccessing AOL Macintosh ClientsLinux Clients To act as a Dhcp Client recommended Port Options Advanced Port SetupOption Settings Port OptionsConnection Options Transparent BridgeLoad Balance Load BalanceInterface Settings Load BalanceLoad Balance StatisticsAdvanced PPPoE Settings Advanced PPPoEAdvanced Pptp Settings Advanced PptpHost IP Setup Advanced ConfigurationHost IP Setup Settings Host IP SetupList Host NetworkBinding Host & GroupVirtual Servers Connecting to the Virtual ServersAddress Settings Virtual ServerEnable Server TypeCustom Server Settings Custom Virtual ServersCustom Virtual Servers Select Custom Server Server List NameCustom Virtual Server Select Special Application Name Select Name Item Settings Special ApplicationsSpecial Application Configuration Special ApplicationsIncoming Port Range Using a Special Application on your PCOutgoing Port Range Incoming ProtocolDynamic DNS To use the Dynamic DNS featureSettings Dynamic DNS Multi DMZ Multi DMZSettings Multi DMZ Settings UPnP UPnPUPnP Option NAT NAT Alias Settings NAT10 Advanced Features Advanced FeaturesSettings Advanced Features Using Remote Web-based Setup Interface Smtp Simple Mail Transport Protocol BindingProtocol Protocol and Port Binding URL Filter Security ManagementBlock Internet Settings URL FilterFilter Setting Access FilterSettings Access Filter Setup Access GroupBlock Block Well-knownPorts User-defined Ports toSession Limit Foreign Port Range Firewall Exception EnableSystem Filter Exception ProtocolFeature QoS ConfigurationQoS Setup Data QoS SetupPolicy Configuration Data Policy ConfigurationNetwork Admission Policy Snmp Management AssistantEmail Alert Settings SnmpEnable/Disable Email Alert Email Alert Configuration Event Settings Email Alert3Syslog SyslogSyslog Configuration Syslog GlobalSyslog Server Admin Password Screen Admin Password ScreenFirmware Upgrade Screen Upgrade FirmwareAdvanced LAN Configuration Existing Dhcp ServerRouting Settings Routing Configuring Other Routers on your LAN Static Routing ExampleFor The Load Balancer Gateways Routing Table For Router As Default Route For Router Bs Default RouteEntry 2 Segment Operation and Status OperationSystem Status Device Data System StatusRestore Factory Defaults Restore Factory DefaultsWAN Status WAN StatusLAN IP Info NAT TimeoutsNAT Status Data NAT StatusNAT Connections ErrorsTCP Prosperity NAT TrafficSpecifications FCC StatementCE Marking Warning Windows TCP/IP Setup Overview TCP/IP SettingsChecking TCP/IP Settings Windows 9x/ME Using Dhcp Select Control Panel Network and Dial-up Connection Checking TCP/IP Settings WindowsUsing a fixed IP Address Use the following IP Address Figure B-7 Network Configuration Windows XP Checking TCP/IP Settings Windows XPFigure B-8 TCP/IP Properties Windows XP Troubleshooting General ProblemsInternet Access Solution