Edimax Technology Edimax user guide Router Rear Panel, Default Settings, Reset Button, LAN Ports

Page 10

Rear Panel

	Figure 1-2: Rear Panel

DC 5V	Connect the supplied power adapter here.

WAN 2	Connect the 2nd Broadband Modem here, if available.
Reset Button	When pressed and released, The Load Balancer will reboot (restart) within 1
	second. It resets to default over 3 seconds.
LAN Ports	Connect the PCs to these ports. Both 10BaseT and 100BaseT connections can
	be used simultaneously.
	Note:
	Any port will automatically operate as an "Uplink" port if required. Just use a
	normal LAN cable to connect to a normal port on another hub.
WAN 1	Connect the primary Broadband Modem here.

Default Settings

When The Load Balancer has finished booting, all configuration settings will be set to the factory defaults, including:

•IP Address set to its default value of 192.168.1.1, with a Network Mask of 255.255.255.0

•DHCP Server is enabled

•User Name: admin

•Password cleared (no password)

TFTP Download

This setting should be used only if your Load Balancer is unusable, and you wish to restore it by downloading new firmware. Follow this procedure:

1.Power On The Load Balancer.

2.Use the supplied Windows utility or a TFTP client program applies the new firmware. If using the supplied Windows TFTP program, the screen will look like the following example.

Page 6

Image 10

Contents Load Balancing Router User’s Guide Page Table of Contents Overview General Problems Internet Access Overview TCP/IP SettingsOperation System Status WAN Status NAT Status Internet Features IntroductionMultiple IP Address Support Other Features Port Switching HubPackage Contents Physical DetailsLED Action Condition Rear Panel Default SettingsReset Button LAN PortsWindows Tftp utility Configuring The Load Balancer for your LAN Basic SetupProcedure OverviewNo Response ? IP Address Settings LAN & DhcpConfiguration Subnet MaskRange LAN Any IP SetupDhcp IP Address ARP ProxyInstalling The Load Balancer in your LAN Installation DiagramConfiguring The Load Balancer for Internet Access Primary Setup ScreenSettings Primary Setup Optional Internet Access Configure PCs on your LANTCP/IP Settings OverviewMacintosh Clients Accessing AOLLinux Clients To act as a Dhcp Client recommended Advanced Port Setup Port OptionsTransparent Bridge Settings Port OptionsConnection Options OptionLoad Balance Load BalanceStatistics Settings Load BalanceLoad Balance InterfaceSettings Advanced PPPoE Advanced PPPoESettings Advanced Pptp Advanced PptpAdvanced Configuration Host IP SetupSettings Host IP Setup Host IP SetupHost & Group Host NetworkBinding ListConnecting to the Virtual Servers Virtual ServersServer Type Settings Virtual ServerEnable AddressSelect Custom Server Server List Name Settings Custom Virtual ServersCustom Virtual Servers Custom ServerCustom Virtual Server Special Applications Settings Special ApplicationsSpecial Application Configuration Select Special Application Name Select Name ItemIncoming Protocol Using a Special Application on your PCOutgoing Port Range Incoming Port RangeTo use the Dynamic DNS feature Dynamic DNSSettings Dynamic DNS Multi DMZ Multi DMZSettings Multi DMZ UPnP Settings UPnPUPnP Option NAT Settings NAT NAT AliasAdvanced Features 10 Advanced FeaturesSettings Advanced Features Interface Smtp Simple Mail Transport Protocol Binding Using Remote Web-based SetupProtocol Protocol and Port Binding Security Management URL FilterSettings URL Filter Block InternetSetup Access Group Access FilterSettings Access Filter Filter SettingUser-defined Ports to Block Well-knownPorts BlockSession Limit Protocol Firewall Exception EnableSystem Filter Exception Foreign Port RangeData QoS Setup QoS ConfigurationQoS Setup FeatureData Policy Configuration Policy ConfigurationNetwork Admission Policy Management Assistant SnmpSettings Snmp Email AlertSettings Email Alert Enable/Disable Email Alert Email Alert Configuration EventSyslog 3SyslogSyslog Global Syslog ConfigurationSyslog Server Admin Password Screen Admin Password ScreenUpgrade Firmware Firmware Upgrade ScreenExisting Dhcp Server Advanced LAN ConfigurationRouting Settings Routing Static Routing Example Configuring Other Routers on your LANFor The Load Balancer Gateways Routing Table For Router Bs Default Route For Router As Default RouteEntry 2 Segment Operation Operation and StatusSystem Status Data System Status DeviceRestore Factory Defaults Restore Factory DefaultsWAN Status WAN StatusData NAT Status NAT TimeoutsNAT Status LAN IP InfoNAT Traffic ErrorsTCP Prosperity NAT ConnectionsFCC Statement SpecificationsCE Marking Warning Overview TCP/IP Settings Windows TCP/IP SetupChecking TCP/IP Settings Windows 9x/ME Using Dhcp Checking TCP/IP Settings Windows Select Control Panel Network and Dial-up ConnectionUsing a fixed IP Address Use the following IP Address Checking TCP/IP Settings Windows XP Figure B-7 Network Configuration Windows XPFigure B-8 TCP/IP Properties Windows XP General Problems TroubleshootingInternet Access Solution