Edimax Technology Edimax user guide Router manual Using Remote Web-based Setup

Page 47

Interface

SMTP (Simple Mail Transport Protocol) Binding

Binding

Unless you are using E-mail accounts from different ISPs on each port, you can

 

 

ignore these settings.

 

Some ISPs configure their E-mail Servers so they will not accept E-mail from IP

 

addresses not allocated by themselves. If you are using accounts from different

 

ISPs, sending E-mail over the wrong port may result in non-acceptance of the

 

mail. In this case, you can use these settings to correct the problem.

 

Enable - If enabled, the port you specify below will be used for all outgoing

 

 

SMTP traffic. If not enabled, either port will be used.

 

WAN 1 / WAN 2 – Select the desired port.

 

 

Protocol &

Protocol and Port Binding

Port Binding

Use these settings if you wish to ensure that particular traffic is sent by a

 

 

particular WAN port, and thereby a particular ISP account.

 

Enable - Enable or disable each item as required.

 

Source IP - IP address of source which packets are sent from.

 

Destination IP – IP address of destination which packets are sent to.

 

Subnet Mask – With subnet mask other than 255.255.255.255, you can

 

 

make a IP sub-network as your destination.

 

Protocol - Select the protocol used by the traffic you wish to configure.

 

Port Range - Enter the beginning and end of the port range used by the traffic

 

 

you wish to configure. If only a single port is used, enter the port number in

 

 

both fields.

 

WAN - Select the port you wish this traffic to use.

Using Remote Web-based Setup

To connect to The Load Balancer from a remote PC via the Internet:

1.Ensure that both your PC and The Load Balancer are connected to the Internet.

2.Start your Web Browser.

3.In the "Address" bar, enter "HTTP://" followed by the Internet IP Address of The Load Balancer. If the port number is not 80, the port number is also required. (After the IP Address, enter ":" followed by the port number.)

e.g.

HTTP://123.123.123.123:8080

This example assumes the WAN IP Address is 123.123.123.123, and the port number is 8080.

If using the Dynamic DNS feature, you can connect using the domain name allocated to you. e.g.

HTTP://my_domain_name.dyndns.org:8080

Page 43

Image 47
Contents Load Balancing Router User’s Guide Page Table of Contents Operation System Status WAN Status NAT Status Overview TCP/IP SettingsOverview General Problems Internet Access Introduction Internet FeaturesMultiple IP Address Support Port Switching Hub Other FeaturesPhysical Details Package ContentsLED Action Condition LAN Ports Default SettingsReset Button Rear PanelWindows Tftp utility Overview Basic SetupProcedure Configuring The Load Balancer for your LANNo Response ? Subnet Mask Settings LAN & DhcpConfiguration IP AddressARP Proxy LAN Any IP SetupDhcp IP Address RangeInstallation Diagram Installing The Load Balancer in your LANPrimary Setup Screen Configuring The Load Balancer for Internet AccessSettings Primary Setup Optional Overview Configure PCs on your LANTCP/IP Settings Internet AccessLinux Clients Accessing AOLMacintosh Clients To act as a Dhcp Client recommended Port Options Advanced Port SetupOption Settings Port OptionsConnection Options Transparent BridgeLoad Balance Load BalanceInterface Settings Load BalanceLoad Balance StatisticsAdvanced PPPoE Settings Advanced PPPoEAdvanced Pptp Settings Advanced PptpHost IP Setup Advanced ConfigurationHost IP Setup Settings Host IP SetupList Host NetworkBinding Host & GroupVirtual Servers Connecting to the Virtual ServersAddress Settings Virtual ServerEnable Server TypeCustom Server Settings Custom Virtual ServersCustom Virtual Servers Select Custom Server Server List NameCustom Virtual Server Select Special Application Name Select Name Item Settings Special ApplicationsSpecial Application Configuration Special ApplicationsIncoming Port Range Using a Special Application on your PCOutgoing Port Range Incoming ProtocolDynamic DNS To use the Dynamic DNS featureSettings Dynamic DNS Multi DMZ Multi DMZSettings Multi DMZ UPnP Option Settings UPnPUPnP NAT NAT Alias Settings NAT10 Advanced Features Advanced FeaturesSettings Advanced Features Protocol Protocol and Port Binding Using Remote Web-based SetupInterface Smtp Simple Mail Transport Protocol Binding URL Filter Security ManagementBlock Internet Settings URL FilterFilter Setting Access FilterSettings Access Filter Setup Access GroupBlock Block Well-knownPorts User-defined Ports toSession Limit Foreign Port Range Firewall Exception EnableSystem Filter Exception ProtocolFeature QoS ConfigurationQoS Setup Data QoS SetupNetwork Admission Policy Policy ConfigurationData Policy Configuration Snmp Management AssistantEmail Alert Settings SnmpEnable/Disable Email Alert Email Alert Configuration Event Settings Email Alert3Syslog SyslogSyslog Server Syslog ConfigurationSyslog Global Admin Password Screen Admin Password ScreenFirmware Upgrade Screen Upgrade FirmwareRouting Advanced LAN ConfigurationExisting Dhcp Server Settings Routing For The Load Balancer Gateways Routing Table Configuring Other Routers on your LANStatic Routing Example Entry 2 Segment For Router As Default RouteFor Router Bs Default Route System Status Operation and StatusOperation Device Data System StatusRestore Factory Defaults Restore Factory DefaultsWAN Status WAN StatusLAN IP Info NAT TimeoutsNAT Status Data NAT StatusNAT Connections ErrorsTCP Prosperity NAT TrafficCE Marking Warning SpecificationsFCC Statement Checking TCP/IP Settings Windows 9x/ME Windows TCP/IP SetupOverview TCP/IP Settings Using Dhcp Select Control Panel Network and Dial-up Connection Checking TCP/IP Settings WindowsUsing a fixed IP Address Use the following IP Address Figure B-7 Network Configuration Windows XP Checking TCP/IP Settings Windows XPFigure B-8 TCP/IP Properties Windows XP Internet Access TroubleshootingGeneral Problems Solution