Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic 50 manual Switcher Error Responses, Using the Command/Response Table

Models: 50

1 74

Download 74 pages 18.11 Kb

Page 43

Switcher Error Responses

The switcher does not expect a response from the host, but, for example, the host program might request a new status.

Switcher Error Responses

When the switcher receives an SIS command and determines that it is valid, it performs the command and sends a response to the host device. If the switcher is unable to perform the command because the command is invalid or contains invalid parameters, the switcher returns an error response to the host. The error response codes are:

E01 — Invalid input channel number (too large)

E10 — Invalid command

E11 — Invalid preset number (too large)

E12 — Invalid output number (too large)

E13 — Invalid value (out of range)

E14 — Illegal command for this configuration

E17 — Timeout (only caused by direct write of global presets)

Using the Command/Response Table

The command/response table begins on the next page. Lower case letters are acceptable in the command field only where indicated. Symbols are used throughout the table to represent variables in the command/response fields. Command and response examples are shown throughout the table.

ASCII to HEX Conversion Table

Space

Matrix 50 Series Switchers • Programmer’s Guide

4-3

Image 43

Extron electronic 50 manual Switcher Error Responses, Using the Command/Response Table

Contents

Matrix 50 Series Matrix Audio/Video Switchers68-218-01 Rev. J Sicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisQS-1 Quick Start - Matrix 50 Series SwitchersInstallation DefinitionsFront Panel Controls Quick Start - Matrix 50 Series Switchers, cont’dSave or recall a preset View and adjust audio levelMatrix 50 Series Switchers Table of Contents Table of Contentsii Matrix 50 Series Switchers Table of Contents Table of Contents, cont’dMatrix 50 Series Switchers Table of Contents Table of Contents, cont’d iv Matrix 50 Series Switchers Table of Contents68-218-01 Rev. J Introduction Matrix 50 Series SwitchersAbout the Matrix 50 Series Switchers Features Chapter1One1-2 Matrix 50 Series Switchers Introduction About the Matrix 50 Series SwitchersIntroductiontroduction, cont’d Figure 1- 1 - A typical Matrix 50 Series Switcher application FeaturesMatrix 50 Series Switchers Introduction Any input to any or all outputs 1-4 Matrix 50 Series Switchers IntroductionIntroduction, cont’d Figure 1-2 - Audio gain and attenuationMatrix 50 Series Switchers Introduction Labeling - Extron’s label software ships with every Extron matrix switcher. You can create labels to place alongside the front panel input buttons and output buttons, with names, alphanumeric characters, or color bitmaps for easy and intuitive input and output selection. Alternatively, labels can be made with any Brother P-Touch or comparable labelerIntroduction, cont’d 1-6 Matrix 50 Series Switchers IntroductionMatrix 50 Series Switchers InstallationRack Mounting the Switcher Cabling and Rear Panel Views Chapter2TwoFigure 2-4 - Rear panel connectors, Matrix 50 audio switcher Installationstallation, cont’dRack Mounting the Switcher Figure 2-2 - Rear panel connectors, Matrix 50 S-video switcherAudio input and output connections audio models only Power connectionMatrix 50 Series Switchers Installation Video input and output connections video models onlyFigure 2-7 - Captive screw connector wiring for audio output Installation, cont’dFigure 2-5 - Captive screw connector wiring for inputs Figure 2-6 - Phono audio connectorsFigure 2-8 -Simple external sync connection example External sync connectionMatrix 50 Series Switchers Installation Figure 2-9 - Multiple device external sync connection example Figure 2-11 - Rear panel view, 8x8 component video Matrix 50 Switcher2-6 Matrix 50 Series Switchers Installation Additional rear panel viewsOperation Front Panel Controls and Indicators Front Panel OperationsTroubleshooting Worksheets Chapter3ThreeOperationeration, cont’d Front Panel Controls and IndicatorsFigure 3-1 - Matrix 50 Series Switcher front panel 3-2 Matrix 50 Series Switchers OperationI/O controls Matrix 50 Series Switchers OperationOperation, cont’d PowerCreating a configuration 3-4 Matrix 50 Series Switchers OperationFigure 3-3 - Example 1 Creating a tie 1. Only one video input and one audio input can be tied to an output5. If an input with no tie is selected, only that input’s LED lights Example 1 Creating a set of video and audio tiesExample 3 Removing a tie from a set of video and audio ties 3-6 Matrix 50 Series Switchers OperationExample 2 Adding a tie to a set of video and audio ties Figure 3-4 - Example 2 Adding a video tieMatrix 50 Series Switchers Operation Viewing a configurationFigure 3-5 - Example 3 Selecting audio and selecting input Figure 3-6 - Example 3d Removing an audio tieOperation, cont’d Figure 3-7 - Example 4 Viewing the current configuration3-8 Matrix 50 Series Switchers Operation Example 4 Viewing video and audio, audio only, and video only tiesMatrix 50 Series Switchers Operation Figure 3-9 - Example 4e Viewing the current configuration, audio onlyand restored, the mute settings are lost When you enter view-only mode, the output LEDs turn on for allWhen you mute video, the mute command mutes all video planes Mutes are not saved to non-volatile memory. When power is removedFigure 3-11 - Example 5, step d Muting and unmuting outputs Using global memory presetsMatrix 50 Series Switchers Operation Figure 3-13 - Example 7 Recalling preset Example 6 Saving a presetFigure 3-12 - Example 6 Saving the current configuration as preset Example 7 Recalling a presetMatrix 50 with audio Viewing and adjusting the audio levelExample 8 Viewing and adjusting an audio level Matrix 50 Series Switchers OperationFigure 3-14 - Example 8 Viewing the audio level Figure 3-15 - Example 8d Adjusting the audio level3-14 Matrix 50 Series Switchers Operation Executive mode front panel security lockoutWorksheets TroubleshootingSystem reset to factory defaults Plasma display S-video problemOperation, cont’d 3-16 Matrix 50 Series Switchers OperationWorksheet example 1 System equipment Figure 3-16 - Worksheet example 1 System equipmentFigure 3-17 - Worksheet example 2 Daily configuration Worksheet example 2 Daily configurationMatrix 50 Series Switchers Operation Operation, cont’d Worksheet example 3 Test configurationFigure 3-18 - Worksheet example 3 Test configuration 3-18 Matrix 50 Series Switchers OperationInput sources Configuration worksheetMatrix 50 Series Switchers Operation Preset #Operation, cont’d 3-20 Matrix 50 Series Switchers OperationChapter4Four Host-to-Switcher Instructions Switcher-Initiated MessagesSwitcher Error Responses Using the Command/Response Table Command/Response Table4-2 Matrix 50 Series Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Figure 4-1 - RS-232/RS-422 connector pin arrangementUsing the Command/Response Table Switcher Error ResponsesMatrix 50 Series Switchers Programmer’s Guide Command Command/Response TableCommand/response table for SIS commands numbers in commandsMatrix 50 Series Switchers Programmer’s Guide Command/response table for SIS commands Cont’dCommand ASCII CommandASCII Command 4-6 Matrix 50 Series Switchers Programmer’s GuideCommand/response table for SIS commands Cont’d CommandMatrix 50 Series Switchers Matrix Switcher+ Control Program Button-Label GeneratorChapter5Five Matrix Software5-2 Matrix 50 Series Switchers Matrix Software Matrix Switcher+ Control ProgramInstalling the software Using the softwareWindows buttons Figure 5-1 - Extron Matrix Switcher+ Control Program window blankMatrix 50 Series Switchers Matrix Software Figure 5-2 - Sample program window completeFile menu 5-4 Matrix 50 Series Switchers Matrix SoftwareMatrix Software, cont’d Windows menusUsing the software Using emulation modeUsing the help system Button-Label GeneratorFigure 5-3 - Extron’s Button-Label Generator window 5-6 Matrix 50 Series Switchers Matrix SoftwareMatrix Software, cont’d Matrix 50 Series Switchers SpecificationsSpecifications Part Numbers AAppendix AVideo input Specificationsecifications, cont’dA-2 Matrix 50 Series Switchers Specifications VideoAudio output Specifications are subject to change without noticeMatrix 50 Series Switchers Specifications Audio inputPart Numbers Specifications, cont’dMatrix 50 Series switchers part numbers A-4 Matrix 50 Series Switchers SpecificationsBNC connectors Optional AccessoriesRG6 super high resolution cable Assorted connectorsSpecifications, cont’d A-6 Matrix 50 Series Switchers SpecificationsPre-cut cables S-video CableMatrix 50 Series Switchers Hardware Procedures Button LabelsAppendixBB Reference InformationReferenceInformation,co t’d Hardware ProceduresOpening the switcher B-2 Matrix 50 Series Switchers Reference InformationFigure B-2 - Side view, Matrix 50 S-video and audio switcher Closing the switcherMatrix 50 Series Switchers Reference Information Figure B-3 - Installing a video module Installing a video moduleinstall the video modules. Return here when finished with the audio module procedureMatrix 50 Series Switchers Reference Information removed, see Setting the front panel jumper , on page B-10Removing a video module removed, see Setting the front panel jumper , on page B-10B-6 Matrix 50 Series Switchers Reference Information Installing an audio moduleFigure B-5 - Installing the audio board Installing a video module on page B-4Installing a video module on page B-4 Figure B-6 - Mounting the audio boardon page B-3 Removing an audio moduleIf not already done, reconnect the AC power, input, and output cables Swapping the serial portsReference Information, cont’d Figure B-8 - Key and pin 1 mark Installing a firmware updateMatrix 50 Series Switchers Reference Information Reference Information, cont’d Setting the front panel jumperB-10 Matrix 50 Series Switchers Reference Information Replacing the AC fuseMatrix 50 Series Switchers Reference Information B-11 Figure B-9 - Jumper settings, Matrix 50 series switchersButton Labels Blank B-12 Matrix 50 Series Switchers Reference InformationReference Information, cont’d Figure B-10 - Button label blanks, 12-button strip Matrix 50 Series Switchers Reference Information B-13Reference Information, cont’d B-14 Matrix 50 Series Switchers Reference InformationEurope, Africa, and the Middle East Extron’s WarrantyFCC Class A Notice USA, Canada, South AmericaExtron Electronics, Japan Extron Electronics, USAExtron Electronics, Europe Extron Electronics, Asia