Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic 50 Specificationsecifications, cont’d, Video input, Video output, Sync

Models: 50

1 74

Download 74 pages 18.11 Kb

Page 54

Specificationsecifications, cont’d

Video

Routing	8 x 4, 8 x 8, 12 x 4, or 12 x 8 matrix
Gain	Unity
Bandwidth	150 MHz (-3dB), fully loaded
	0 - 10 MHz	no more than 0.1dB to -0.1dB
	0 - 130 MHz	no more than 0.5dB to -0.5dB
Phase between I/Os	<1.28º at 3.58 MHz
Differential phase error	0.1%, 3.58 and 4.43 MHz
Differential gain error	0.1º, 3.58 and 4.43 MHz
Max. propagation of delay	5 ns typical (±1 ns)
Crosstalk	-50dB @ 5 MHz
Switching speed	200 ns (max.)

Video input

Number/signal type	8 or 12 RGsB, RsGsBs, component video (Y, R-Y, B-Y), HDTV, S-video,
	composite video
Connectors	(8 or 12) x 1, 2, or 3 BNC female
Nominal levels	1V p-p for Y of component video and S-video, and for composite video
	0.7V p-p for RGB
	0.3V p-p for R-Y and B-Y of component video, and for C of S-video
Minimum/maximum levels	Analog: 0.5V to 2V p-p with no offset
Impedance	75 ohms
Return loss	-30dB @ 5 MHz
Maximum DC offset	1.5V
External sync (genlock)	0.3V to 0.4V p-p

Video output

Number/signal type	4 or 8 RGsB, RsGsBs, component video (Y, R-Y, B-Y), HDTV, S-video,
	composite video
Connectors	(4 or 8) x 1, 2, or 3 BNC female
Nominal levels	1V p-p for Y of component video and S-video, and for composite video
	0.7V p-p for RGB
	0.3V p-p for R-Y and B-Y of component video, and for C of S-video
Minimum/maximum levels	0.5V to 2.0V p-p
Impedance	75 ohms
Return loss	-30dB @ 5 MHz
DC offset	±5mV maximum with input at 0 offset
Switching type	Vertical interval

Sync

Input type	RGsB, RsGsBs
Output type	RGsB, RsGsBs
Genlock connectors	BNC female
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM

Audio

Routing	8 x 4, 8 x 8, 12 x 4, or 12 x 8 matrix
Gain	Unbalanced output: 0dB; balanced output: +6dB
Frequency response	20 Hz to 20 kHz, ±0.05dB
THD + Noise	0.03% @ 1 kHz at nominal level
S/N	>90dB, balanced, at rated maximum output (21dBu)

A-2 Matrix 50 Series Switchers • Specifications

Image 54

Extron electronic 50 manual Specificationsecifications, cont’d, Video input, Video output, Sync, Audio

Contents

Matrix Audio/Video Switchers Matrix 50 Series68-218-01 Rev. J Consignes de Sécurité Français PrecautionsSafety Instructions English Sicherheitsanleitungen DeutschDefinitions Quick Start - Matrix 50 Series SwitchersInstallation QS-1View and adjust audio level Quick Start - Matrix 50 Series Switchers, cont’dSave or recall a preset Front Panel ControlsTable of Contents Matrix 50 Series Switchers Table of ContentsTable of Contents, cont’d ii Matrix 50 Series Switchers Table of ContentsMatrix 50 Series Switchers Table of Contents iv Matrix 50 Series Switchers Table of Contents Table of Contents, cont’d68-218-01 Rev. J Chapter1One Matrix 50 Series SwitchersAbout the Matrix 50 Series Switchers Features IntroductionAbout the Matrix 50 Series Switchers 1-2 Matrix 50 Series Switchers IntroductionIntroductiontroduction, cont’d Features Figure 1- 1 - A typical Matrix 50 Series Switcher applicationMatrix 50 Series Switchers Introduction Figure 1-2 - Audio gain and attenuation 1-4 Matrix 50 Series Switchers IntroductionIntroduction, cont’d Any input to any or all outputsLabeling - Extron’s label software ships with every Extron matrix switcher. You can create labels to place alongside the front panel input buttons and output buttons, with names, alphanumeric characters, or color bitmaps for easy and intuitive input and output selection. Alternatively, labels can be made with any Brother P-Touch or comparable labeler Matrix 50 Series Switchers Introduction1-6 Matrix 50 Series Switchers Introduction Introduction, cont’dChapter2Two InstallationRack Mounting the Switcher Cabling and Rear Panel Views Matrix 50 Series SwitchersFigure 2-2 - Rear panel connectors, Matrix 50 S-video switcher Installationstallation, cont’dRack Mounting the Switcher Figure 2-4 - Rear panel connectors, Matrix 50 audio switcherVideo input and output connections video models only Power connectionMatrix 50 Series Switchers Installation Audio input and output connections audio models onlyFigure 2-6 - Phono audio connectors Installation, cont’dFigure 2-5 - Captive screw connector wiring for inputs Figure 2-7 - Captive screw connector wiring for audio outputExternal sync connection Figure 2-8 -Simple external sync connection exampleMatrix 50 Series Switchers Installation Additional rear panel views Figure 2-11 - Rear panel view, 8x8 component video Matrix 50 Switcher2-6 Matrix 50 Series Switchers Installation Figure 2-9 - Multiple device external sync connection exampleChapter3Three Front Panel Controls and Indicators Front Panel OperationsTroubleshooting Worksheets Operation3-2 Matrix 50 Series Switchers Operation Front Panel Controls and IndicatorsFigure 3-1 - Matrix 50 Series Switcher front panel Operationeration, cont’dMatrix 50 Series Switchers Operation I/O controls3-4 Matrix 50 Series Switchers Operation PowerCreating a configuration Operation, cont’dExample 1 Creating a set of video and audio ties 1. Only one video input and one audio input can be tied to an output5. If an input with no tie is selected, only that input’s LED lights Figure 3-3 - Example 1 Creating a tieFigure 3-4 - Example 2 Adding a video tie 3-6 Matrix 50 Series Switchers OperationExample 2 Adding a tie to a set of video and audio ties Example 3 Removing a tie from a set of video and audio tiesFigure 3-6 - Example 3d Removing an audio tie Viewing a configurationFigure 3-5 - Example 3 Selecting audio and selecting input Matrix 50 Series Switchers OperationExample 4 Viewing video and audio, audio only, and video only ties Figure 3-7 - Example 4 Viewing the current configuration3-8 Matrix 50 Series Switchers Operation Operation, cont’dFigure 3-9 - Example 4e Viewing the current configuration, audio only Matrix 50 Series Switchers OperationMutes are not saved to non-volatile memory. When power is removed When you enter view-only mode, the output LEDs turn on for allWhen you mute video, the mute command mutes all video planes and restored, the mute settings are lostUsing global memory presets Figure 3-11 - Example 5, step d Muting and unmuting outputsMatrix 50 Series Switchers Operation Example 7 Recalling a preset Example 6 Saving a presetFigure 3-12 - Example 6 Saving the current configuration as preset Figure 3-13 - Example 7 Recalling presetMatrix 50 Series Switchers Operation Viewing and adjusting the audio levelExample 8 Viewing and adjusting an audio level Matrix 50 with audioExecutive mode front panel security lockout Figure 3-15 - Example 8d Adjusting the audio level3-14 Matrix 50 Series Switchers Operation Figure 3-14 - Example 8 Viewing the audio levelPlasma display S-video problem TroubleshootingSystem reset to factory defaults WorksheetsFigure 3-16 - Worksheet example 1 System equipment 3-16 Matrix 50 Series Switchers OperationWorksheet example 1 System equipment Operation, cont’dWorksheet example 2 Daily configuration Figure 3-17 - Worksheet example 2 Daily configurationMatrix 50 Series Switchers Operation 3-18 Matrix 50 Series Switchers Operation Worksheet example 3 Test configurationFigure 3-18 - Worksheet example 3 Test configuration Operation, cont’dPreset # Configuration worksheetMatrix 50 Series Switchers Operation Input sources3-20 Matrix 50 Series Switchers Operation Operation, cont’dCommand/Response Table Host-to-Switcher Instructions Switcher-Initiated MessagesSwitcher Error Responses Using the Command/Response Table Chapter4FourFigure 4-1 - RS-232/RS-422 connector pin arrangement Host-to-Switcher InstructionsSwitcher-Initiated Messages 4-2 Matrix 50 Series Switchers Programmer’s GuideSwitcher Error Responses Using the Command/Response TableMatrix 50 Series Switchers Programmer’s Guide numbers in commands Command/Response TableCommand/response table for SIS commands CommandASCII Command Command/response table for SIS commands Cont’dCommand Matrix 50 Series Switchers Programmer’s GuideCommand 4-6 Matrix 50 Series Switchers Programmer’s GuideCommand/response table for SIS commands Cont’d ASCII CommandMatrix Software Matrix Switcher+ Control Program Button-Label GeneratorChapter5Five Matrix 50 Series SwitchersUsing the software Matrix Switcher+ Control ProgramInstalling the software 5-2 Matrix 50 Series Switchers Matrix SoftwareFigure 5-2 - Sample program window complete Figure 5-1 - Extron Matrix Switcher+ Control Program window blankMatrix 50 Series Switchers Matrix Software Windows buttonsWindows menus 5-4 Matrix 50 Series Switchers Matrix SoftwareMatrix Software, cont’d File menuButton-Label Generator Using emulation modeUsing the help system Using the software5-6 Matrix 50 Series Switchers Matrix Software Figure 5-3 - Extron’s Button-Label Generator windowMatrix Software, cont’d AAppendix A SpecificationsSpecifications Part Numbers Matrix 50 Series SwitchersVideo Specificationsecifications, cont’dA-2 Matrix 50 Series Switchers Specifications Video inputAudio input Specifications are subject to change without noticeMatrix 50 Series Switchers Specifications Audio outputA-4 Matrix 50 Series Switchers Specifications Specifications, cont’dMatrix 50 Series switchers part numbers Part NumbersAssorted connectors Optional AccessoriesRG6 super high resolution cable BNC connectorsS-video Cable A-6 Matrix 50 Series Switchers SpecificationsPre-cut cables Specifications, cont’dReference Information Hardware Procedures Button LabelsAppendixBB Matrix 50 Series SwitchersB-2 Matrix 50 Series Switchers Reference Information Hardware ProceduresOpening the switcher ReferenceInformation,co t’dClosing the switcher Figure B-2 - Side view, Matrix 50 S-video and audio switcherMatrix 50 Series Switchers Reference Information finished with the audio module procedure Installing a video moduleinstall the video modules. Return here when Figure B-3 - Installing a video moduleremoved, see Setting the front panel jumper , on page B-10 removed, see Setting the front panel jumper , on page B-10Removing a video module Matrix 50 Series Switchers Reference InformationInstalling a video module on page B-4 Installing an audio moduleFigure B-5 - Installing the audio board B-6 Matrix 50 Series Switchers Reference InformationRemoving an audio module Figure B-6 - Mounting the audio boardon page B-3 Installing a video module on page B-4Swapping the serial ports If not already done, reconnect the AC power, input, and output cablesReference Information, cont’d Installing a firmware update Figure B-8 - Key and pin 1 markMatrix 50 Series Switchers Reference Information Replacing the AC fuse Setting the front panel jumperB-10 Matrix 50 Series Switchers Reference Information Reference Information, cont’dFigure B-9 - Jumper settings, Matrix 50 series switchers Matrix 50 Series Switchers Reference Information B-11Button Labels B-12 Matrix 50 Series Switchers Reference Information BlankReference Information, cont’d Matrix 50 Series Switchers Reference Information B-13 Figure B-10 - Button label blanks, 12-button stripB-14 Matrix 50 Series Switchers Reference Information Reference Information, cont’dUSA, Canada, South America Extron’s WarrantyFCC Class A Notice Europe, Africa, and the Middle EastExtron Electronics, Asia Extron Electronics, USAExtron Electronics, Europe Extron Electronics, Japan