Example 6 Saving a preset | Extron electronic 50 specification

Operation, cont’d

Example 6: Saving a preset

See figure 3-12 and the following steps for an example of saving the current configuration as a preset on a 12x8 Matrix 50 switcher with audio.

1
F				LED key:			= off,		B	= blinking,
Press							F = flash once
		C					F = flash once
		C
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
1	2	3	4	5	6	7	8
			OUTPUTS

C

Hold B	F Press
B		A
PRESET	ESC
CONTROL		I/O
ENTER PRESET VIEW	ESC	VIDEO AUDIO

Figure 3-12 — Example 6: Saving the current configuration as preset 1

APress and release the Esc button. The Esc LED flashes once.

BPress and hold the Preset button for approximately 2 seconds until the Preset LED begins to blink, then release the Preset button.

CPress and release the input 1 button. The input 1 LED lights flashes once. The Preset LED turns off.

Example 7: Recalling a preset

See figure 3-13 and the following steps for an example of recalling the current configuration as a preset on a 12x8 Matrix 50 switcher with audio.

F				LED key:			= off,		= on
Press							= flash once
		C				F	= flash once
		C
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
1	2	3	4	5	6	7	8
			OUTPUTS

C

Press	F	Press
Press		Press
B		A
PRESET	ESC
CONTROL		I/O
ENTER PRESET VIEW	ESC	VIDEO AUDIO

Figure 3-13 — Example 7: Recalling preset 1

APress and release the Esc button. The Esc LED flashes once.

BPress and release the Preset button. The Preset LED lights.

CPress and release the input 1 button. The input 1 LED flashes once. The Preset LED turns off. The configuration stored in memory location 1 is now the current configuration and can be viewed in the view-only mode (Example 4).

3-12 Matrix 50 Series Switchers • Operation

Image 32

Extron electronic 50 manual Example 6 Saving a preset, Example 7 Recalling a preset

Contents

Matrix Audio/Video Switchers Matrix 50 Series Safety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad Español Quick Start Matrix 50 Series Switchers QS-1 Quick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One Introductiontroduction, cont’d About the Matrix 50 Series SwitchersMatrix 50 Series Switchers Introduction Features Matrix Matrix 50 switcher Introduction, cont’d Matrix 50 Series Switchers Introduction Introduction, cont’d Two Installationstallation, cont’d Rack Mounting the SwitcherMatrix 50 Series Switchers Installation Cabling and Rear Panel Views Audio input and output connections audio models only Power connectionVideo input and output connections video models only Installation, cont’d RS-232/422 connection External sync connection Simple external sync connection example Additional rear panel views Multiple device external sync connection example Three Front Panel Controls and Indicators Operationeration, cont’dDefinitions Input buttons, output buttons, and LEDs Controls Power Creating a configurationOperation, cont’d Front Panel Operations Example 1 Creating a set of video and audio ties Example 1 Creating a tie Example 2 Adding a tie to a set of video and audio ties Example 3 Removing a tie from a set of video and audio ties Viewing a configuration Example 3 Selecting audio and selecting input Example 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using global memory presets 11 Example 5, step d Muting and unmuting outputs Example 6 Saving a preset Example 7 Recalling a preset Viewing and adjusting the audio level Example 8 Viewing and adjusting an audio level Executive mode front panel security lockout 14 Example 8 Viewing the audio level Troubleshooting System reset to factory defaultsPlasma display S-video problem Worksheets Worksheet example 1 System equipment 16 Worksheet example 1 System equipment Worksheet example 2 Daily configuration 17 Worksheet example 2 Daily configuration Worksheet example 3 Test configuration 18 Worksheet example 3 Test configuration Configuration worksheet Operation, cont’d Four Host-to-Switcher Instructions Switcher-Initiated MessagesMatrix 50 Series Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’d Switcher Error Responses Using the Command/Response Table Programmer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d View ties, gain, and presets Five Matrix Switcher+ Control Program Installing the softwareUsing the software MatrixSoftware,cont’d Extron Matrix Switcher+ Control Program window blank Windows buttons Matrix Software, cont’d Windows menus Button-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d Matrix 50 Series Switchers Specifications Audio input Specifications, cont’d Matrix 50 Series switchers part numbersPart Numbers Matrix 50 Option Kits Optional Accessories Cables Video Cable Pre-cut cablesExtron Part BNC-4 Mini HR Cable AppendixBB Hardware Procedures Opening the switcherMatrix 50 Series Switchers Reference Information ReferenceInformation,co t’d Closing the switcher Figure B-2 Side view, Matrix 50 S-video and audio switcher Installing a video module Reference Information, cont’d Removing a video module Installing an audio module Removing a video module on page B-5 On page B-3 Removing an audio module Swapping the serial ports Installing a firmware update Figure B-8 Key and pin 1 mark Setting the front panel jumper Replacing the AC fuse Matrix 50 Series Switchers Reference Information B-11 Button Labels Blank Matrix 50 Series Switchers Reference Information B-13 Figure B-10 Button label blanks, 12-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA