Field Controls 10 manual Notice to the user, Regulatory

Page 34
Notice to the user

Hardware Platform 10 Installation Guide

Notice to the user

Regulatory

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING: Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Neither the provider nor the manufacturer are responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

CE Notice

This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22/European Standard EN 55022. The limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment.

Attention: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Industry Canada Notice

This Class A digital apparatus complies with Canadian ICES-003.

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

34

Image 34
Contents FChwp10 Installation Guide Hardware PlatformPage Installation Warning Safety InformationQualified Personnel Warning Disclaimer Restricted Access Area WarningSoftware License Terms End User License Agreement Power Supply Disconnection Warning Device handlingPhysical Dimensions Table of ContentsPorts on your controller Pin Assignments Technical Specifications About this manualAbout this manual Organisation of the documentationGetting familiar InstallationSystem requirements FrontBack Bottom Physical installation Hardware installationConnecting power Hardware Platform 10 Installation Guide Power Over Ethernet Connecting to the network When you co-locate the controller, you can connect to it through aHardware Platform 10 Installation Guide IP configuration Addressing basicsAssigning an IP address on a FieldCommander Configure IP address with browsername of the user currently logged in currently admin User name admin Password admincurrently installed firmware version Note that both fields are case sensitiveBootstrap Protocol Dynamic Host Configuration ProtocolBootp Address Resolution ProtocolForce new IP address using ARP+PING Assigning an IP address on an ELS controller Assigning an IP address on an EWS controller The ping test Testing the Ethernet connectionThe browser test The RS-232c standard Serial interfaceRS-232 The connectionsRS-485 option only The RS-485 standardA Backbone with stubs workable B Daisy chain best C Star network avoid D Mixed, backbone & star avoidThe RS-485 pin-out Ports on your controller Pin Assignments Pin Assignments Ethernet POE GND power returnSignal ColorVGAGreen Hardware Platform 10 Installation Guide VGAVGARed VGABlueTechnical Specifications type C 4GB GB Flash drive 256MB reserved for systemUSB Interface option only Hardware Platform 10 Installation Guide RS-485 Interface option onlyNetwork Interface Video Interface model C onlyPhysical Dimensions All sizes in millimetersNotice to the user RegulatoryCopyrights TrademarksDeclaration of Confority NL 4700 AG Roosendaal The Netherlands TEL +31 0165 FAX +31 0165 FieldCommander is a product of CER International bv PostbusThe latest documentation is available Part no. FCHWP10IG, revision