Zonet Technology ZSR0104C Series user manual For Unix/Linux

Page 57

5. For Unix/Linux

If you use Unix or Linux, follow the steps to verify the IP settings in your client PC.

Step 1. To release the previous IP settings of your computer, run the command “kill all dhcpcd”.

Step 2. To obtain new IP settings from ZSR0104C SERIES, run the command “dhcpcd eth#”. “#” Means the number of the Ethernet Network Interface Card installed in your client computer.

Step 3. To learn the new IP settings, please run the command “ipconfig eth#”. “#” Means the number of the Ethernet Network Interface Card installed in your client computer. It will show the IP address and Subnet Mask of your client PC. Then run the command “route –n”, the IP address of your Default Gateway will be displayed. It means your router’s IP address. Make sure that your IP address is 192.168.1.xxx (xxx ranges from 2 to 254), your Subnet Mask is 255.255.255.0, and your Default gateway is 192.168.1.1. These values confirm that your ZSR0104C SERIES is functioning.

Page 50

Image 57

Contents ZSR0104C Series FCC Interference Statement LAN Specifications of ZSR0104C SeriesTable of Contents Advanced Setup of ZSR0104C Series Appendix a Page Physical Features of ZSR0104C Series ZSR0104C Series Broadband Switch RouterNon-Physical Features of ZSR0104C Series Introduction‧ Dynamic DNS ‧ Firewall‧ Virtual Server Port Forwarding ‧ VPN Pass-ThroughPackage Checklist Installation RequirementsAbout this User’s Manual Configure Your ZSR0104C Series Install Your ZSR0104C SeriesOrganization of This User’s Manual Introduction Get to Know the HardwareLED Indicators Get to Know The HardwareZSR0104CP Front Panel ZSR0104C Front Panel Back Panel Reset ButtonLocal LAN Ports Internet WAN PortConnect Ethernet Hub/Switch to ZSR0104C Series Install Your ZSR0104C SeriesConnect Wireless Access Point to ZSR0104C Series Connect Client PC to ZSR0104C SeriesWizard Setup Power up ZSR0104C SeriesUse Your ZSR0104C Series Check the Web ProxyAdministration in Configure Your ZSR0104C Series Page Cable Modem Connection Fixed-IP xDSL Connection PPP over Ethernet PPPoE Connection Pptp Connection Page Advanced Setup of ZSR0104C WAN Setup CompleteStart from Advanced Setting System Administration Default Time Server IP Address is 198.123.30.132Time WAN Side Administration Change Administrator’s User Name and PasswordPre-requirements Firmware UpgradePage Reset Dynamic DNS Domain Name System Page Dhcp Definition Dhcp ServerDhcp Server in LAN Auto-RememberStatic IP Assign Dhcp Client in LANPool Range of Assigned IP Address Dhcp IP Address Lease TimeConfigure TCP/IP in Your PC Virtual Server Port ForwardingDhcp Client List Page DMZ Host Configuration FirewallLocal DMZ Host Public DMZ Host Anti Ping and TCP/UDP Echo Attack URL Filter DisablePort Filter Blocking the following portPlease refer to Appendix B Common Port Numbers MAC FilterBlocking the following Mac Forwarding the following Mac onlyTroubleshooting IP FilterBlocking the following IP Failed Connection between ZSR0104C Series and Client PC Router’s Hardware FailureForget Passwords? Failed Connection on ZSR0104C Series WAN SideDNS Domain Name System Failure Appendix a Disable Web ProxyFor Windows 95 / 98 / ME / 2000 /NT Internet ExplorerFigure A-23 Figure A-25 NetscapeFigure A-26 For Windows XPFigure A-29 Figure A-31 For MAC For Unix/LinuxExplorer For Windows 95 / 98 / ME Verify IP SettingsFigure A-36 Figure A-38 For Windows 2000 /NTFigure A-40 Figure A-43 Figure A-44 For Unix/Linux Appendix B Common Port Numbers Port Number Service NameAppendix C Terminology ‧ Firmware ‧ Infrastructure Mode‧ Gateway ‧ Hardware‧ MSN Messenger ‧ IP Address‧ NetMeeting ‧ Port‧ Switch ‧ RJ-45 Connector‧ Router ‧ ServerSoftware Download Installation/Application Problem Hardware Problem‧ Wireless LAN Appendix D Technical Support