Atlantis Land Mistral Lan Router ISDN manual Filtering Commands ⊕add filter, Conditions Values

Page 22

Caller ID:

None

 

Callback #:

None

Auth Method:

Either

Compression:

No

 

Encryption:

No

Idle Timeout:

300

Enable IP:

Yes

 

IP RIP:

Disable

IP Address:

Dynamic

 

 

 

Bridging:

No

 

 

 

Filtering Commands

⊕add filter <1-8>

Description: This command adds or modifies the nth IP filter rule in the system

Packet Filtering allows each IP packet exiting a router interface to be examined for a match with a configured set of rules. If all of the conditions in any rule do not match the contents of the packet, then the packet is either forwarded or discarded, depending upon the filter default for that interface. Otherwise, the exception action is taken, i.e., the packet is discarded or forwarded, the opposite of the default action. The default action for an interface is set by the set filter default command described below.

The total number of rules system-wide in this version of the firmware is limited to eight. Each of these rules may be assigned to one specific interface.

The conditions that may be specified are:

Conditions

 

Values

 

 

 

IP Protocol

1.

Any Protocol

 

2.

TCP

 

3.

UDP

 

4.

ICMP

 

5.

IGMP

Source IP Address

1.

Any value (wildcard)

 

2.

Individual IP Address (xxx.xxx.xxx.xxx)

 

3.

Range of consecutive IP Addresses

 

 

(xxx.xxx.xxx.xxx-yyy.yyy.yyy.yyy)

 

4.

A Network of IP Addresses (and its associated subnet mask).

 

 

(xxx.xxx.xxx.xxx/mmm.mmm.mmm.mmm)

Destination IP Address

1.

Any value (wildcard)

 

2.

Individual IP Address (xxx.xxx.xxx.xxx)

 

3.

Range of consecutive IP Addresses

 

 

(xxx.xxx.xxx.xxx-yyy.yyy.yyy.yyy)

 

4.

A Network of IP Addresses (and its associated subnet mask).

 

 

(xxx.xxx.xxx.xxx/mmm.mmm.mmm.mmm)

Source TCP/UDP Port

1.

Any value (wildcard)

 

2.

A TCP or UDP Port Number

 

3.

A consecutive range of TCP/UDP Port Numbers

Destination TCP/UDP Port

1.

Any value (wildcard)

 

2.

A TCP or UDP Port Number

 

3.

A consecutive range of TCP/UDP Port Numbers

Filter is specified by a number.

Note: Incorrect or mistyped filtering entries may cause undesired orunpredictable behavior. It is strongly recommended that this feature be used with the utmost care and

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Mistral Lan Router Isdn Support Console Commands Express Mode vs. Advanced Mode Conventions Bridging Commands Compression CommandsDiagnostic Commands Dhcp CommandsDial-in User Commands Filtering Commands IP CommandsPort Commands Security Command Profile CommandsSnmp Commands Statistics Commands System CommandsPage Disable learning Command Detail Bridging CommandsDisable bridging Interface Name Enable bridging Interface NameShow learning Interface Name Show learningClear compression statistics Profile Name Enable compression Profile Name Disable compression Profile NameShow compression statistics Profile Name Add dns primary/secondary IPaddr Disable dhcp⊕add dhcp entry entry name Delete dhcp entry entry name⊕set dhcp Enable dhcp⊕set range Show dhcp table Show dhcpShow range Enable trace Diagnostic Commands Connect profile Profile NameDisable trace Disconnect profile Profile NameTest isdn dial name 64k/56k Delete user profile name Show user profile nameFiltering Commands ⊕add filter Conditions ValuesDelete filter ⊕set filter defaultShow filter ⊕add pat entry public port # ⊕add pat entry default Delete ip route ipAddr netmask Delete ip default routeDelete pat entry default Delete ip Interface NameSet ip lan ipaddr netMask Set ip private ipaddr netMaskSet ip rip Interface Name disabled/passive/active rip1/rip2 Show arp table 255.255.255.0Show ip interface name Show ipShow ip routing table Show ip statistics Show patShow udp statistics Show tcp statisticsClear port statistics port name ⊕set port port name Disable port port name Enable port port nameShow port Show port port name Show port statistics port nameTotal Packets Total Error B2-Channel Total Octets Example 1 Set up an Internet Access Profile over Isdn ⊕add profile Profile NameClear profile statistics Profile Name Disable profile Profile NameDelete profile Profile Name Show profile Enable profile Profile NameShow profile Profile Name Show profile statistics Profile Name Security Command Set ip private ipaddr netMaskShow profile statistics Clear trap managerSet trap manager 1-5 ipAddr Disable trap Enable trapSet community string read password Show snmp statisticsShow trap manager Show icmp statisticsSystem Commands Change password Show Interface Name statisticsDownload config fileName from ipAddr Clear configDisable remote-mgt Enable remote-mgt Disconnect telnet sessionSet console timeout Reset systemSave config LogoutSet daylight time on/off ⊕set internet access timeSet date mm-dd-yy Set prompt promptSet system name system name Set system contact nameSet system location location information Set time hhmmssShow connection log Show configShow internet access time Show interface listShow system log Show telnet session Upload config fileName to ipAddrShow time

Mistral Lan Router ISDN specifications

The Atlantis Land Mistral Lan Router ISDN is a streamlined networking solution designed to meet the demands of modern home and small office environments. Combining functionality with user-friendly features, this router provides a reliable connection for multiple devices, ensuring high-speed internet access and efficient data transmission.

One of the standout features of the Mistral is its ISDN compatibility, allowing users to integrate their existing digital phone lines with the network. This is particularly beneficial for businesses that require dependable and clear voice communications alongside internet connectivity. The system supports both BRI (Basic Rate Interface) and PRIs (Primary Rate Interface), making it adaptable for various telephony needs.

The router is equipped with advanced routing protocols, offering robust performance for data-heavy applications such as video conferencing and online gaming. It supports NAT (Network Address Translation), enabling multiple devices to share a single IP address while maintaining reliable connections. In addition, the Mistral utilizes DHCP (Dynamic Host Configuration Protocol), which simplifies the process of assigning IP addresses to devices on the network, allowing for easy scalability as more devices are added.

Security is a priority with the Atlantis Land Mistral, and it comes with built-in firewall capabilities to protect against unauthorized access and cyber threats. The router supports various encryption methods, ensuring that data transmitted over the network remains secure. These features are essential for users who frequently deal with sensitive information or those who operate in data-sensitive industries.

The configuration process of the Mistral is user-friendly, thanks to its intuitive web-based interface that allows for quick setup and management. Users can easily monitor network performance, manage connected devices, and customize settings to optimize connectivity based on their specific requirements.

Additionally, the Mistral Lan Router ISDN is designed with energy efficiency in mind, incorporating features that minimize power consumption without sacrificing performance. Its compact design ensures that it fits seamlessly into any workspace, making it a practical choice for users seeking a reliable and aesthetically pleasing networking solution.

In summary, the Atlantis Land Mistral Lan Router ISDN stands out for its ISDN compatibility, advanced routing capabilities, strong security features, user-friendly setup, and energy efficiency. It serves as a comprehensive networking solution that caters to both home users and small businesses, ensuring reliable connectivity and high performance in a competitive digital landscape.
Top Page Image Contents