Atlantis Land Mistral Lan Router ISDN Set ip lan ipaddr netMask, Set ip private ipaddr netMask

Page 26

Since dial-up connection (e.g. ISDN calls) charges are based on the connection time, a technique called IP spoofing is often used to limit or prevent unnecessary connection time. This is done by (1) allowing control packets to be sent only when the connection is already up transmitting user data, or

(2)allowing control packets to be spoofed (faked) so that they don’t add load to the WAN traffic. IP RIP broadcasts are sent only when the connection is up.

Example:

Router> enable spoofing isdn1 iprip

Router> disable spoofing isp2 iprip

ping <ipAddr> [n_times] [n_size]

Description: See description under Diagnostics.

set ip default route <gateway-ipAddr> set ip default route <Profile Name>

Description: This command is used to set the IP default route. The default route will be used when an IP packet’s destination IP address cannot be found in the IP routing table. If the default route is not defined, such a packet is discarded.

Example:

Router> set ip default route 204.71.220.153

Router> set ip default route isp1

set ip lan <ip_addr> <netMask>

Description: This command assigns a “public” IP address to the LAN port of the router. As a consequence, the LAN port maps to two IP addresses (one public and one private), and is therefore on two networks.

Example:

Router> set ip lan 204.71.220.153 255.255.255.0

set ip private <ip_addr> <netMask>

Description: This command is used to modify the “private” IP address on the router’s LAN interface.

The IP network corresponding to the “set ip private” command becomes the private network. Private addresses are not legal for use on the Internet and therefore, devices in this network are no longer accessible from public devices on the Internet side. All devices within this “private” network are represented by one single IP address: the IP address received from an Internet Service Provider at connect time. Note that 192.168.168.230 is the default private address used for routers, and the private network address is 192.168.168.0, and therefore all private devices (by default) should have IP addresses within the range of 192.168.168.1 to 192.168.168.254. Private IP addresses may be any Class A, B or C address as described in the “DHCP” section of this manual.

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Mistral Lan Router Isdn Support Console Commands Express Mode vs. Advanced Mode Conventions Bridging Commands Compression CommandsDial-in User Commands Dhcp CommandsDiagnostic Commands Filtering Commands IP CommandsPort Commands Snmp Commands Profile CommandsSecurity Command Statistics Commands System CommandsPage Disable learning Command Detail Bridging CommandsDisable bridging Interface Name Enable bridging Interface NameClear compression statistics Profile Name Show learningShow learning Interface Name Show compression statistics Profile Name Disable compression Profile NameEnable compression Profile Name Add dns primary/secondary IPaddr Disable dhcp⊕add dhcp entry entry name Delete dhcp entry entry name⊕set range Enable dhcp⊕set dhcp Show range Show dhcpShow dhcp table Enable trace Diagnostic Commands Connect profile Profile NameDisable trace Disconnect profile Profile NameTest isdn dial name 64k/56k Delete user profile name Show user profile nameFiltering Commands ⊕add filter Conditions ValuesShow filter ⊕set filter defaultDelete filter ⊕add pat entry public port # ⊕add pat entry default Delete ip route ipAddr netmask Delete ip default routeDelete pat entry default Delete ip Interface NameSet ip lan ipaddr netMask Set ip private ipaddr netMaskSet ip rip Interface Name disabled/passive/active rip1/rip2 Show arp table 255.255.255.0Show ip routing table Show ipShow ip interface name Show ip statistics Show patClear port statistics port name Show tcp statisticsShow udp statistics Show port Disable port port name Enable port port name⊕set port port name Show port port name Show port statistics port nameTotal Packets Total Error B2-Channel Total Octets Example 1 Set up an Internet Access Profile over Isdn ⊕add profile Profile NameDelete profile Profile Name Disable profile Profile NameClear profile statistics Profile Name Show profile Profile Name Enable profile Profile NameShow profile Show profile statistics Profile Name Security Command Set ip private ipaddr netMaskShow profile statistics Clear trap managerSet trap manager 1-5 ipAddr Disable trap Enable trapSet community string read password Show snmp statisticsShow trap manager Show icmp statisticsSystem Commands Change password Show Interface Name statisticsDownload config fileName from ipAddr Clear configDisable remote-mgt Enable remote-mgt Disconnect telnet sessionSet console timeout Reset systemSave config LogoutSet daylight time on/off ⊕set internet access timeSet date mm-dd-yy Set prompt promptSet system name system name Set system contact nameSet system location location information Set time hhmmssShow connection log Show configShow internet access time Show interface listShow system log Show time Upload config fileName to ipAddrShow telnet session

Mistral Lan Router ISDN specifications

The Atlantis Land Mistral Lan Router ISDN is a streamlined networking solution designed to meet the demands of modern home and small office environments. Combining functionality with user-friendly features, this router provides a reliable connection for multiple devices, ensuring high-speed internet access and efficient data transmission.

One of the standout features of the Mistral is its ISDN compatibility, allowing users to integrate their existing digital phone lines with the network. This is particularly beneficial for businesses that require dependable and clear voice communications alongside internet connectivity. The system supports both BRI (Basic Rate Interface) and PRIs (Primary Rate Interface), making it adaptable for various telephony needs.

The router is equipped with advanced routing protocols, offering robust performance for data-heavy applications such as video conferencing and online gaming. It supports NAT (Network Address Translation), enabling multiple devices to share a single IP address while maintaining reliable connections. In addition, the Mistral utilizes DHCP (Dynamic Host Configuration Protocol), which simplifies the process of assigning IP addresses to devices on the network, allowing for easy scalability as more devices are added.

Security is a priority with the Atlantis Land Mistral, and it comes with built-in firewall capabilities to protect against unauthorized access and cyber threats. The router supports various encryption methods, ensuring that data transmitted over the network remains secure. These features are essential for users who frequently deal with sensitive information or those who operate in data-sensitive industries.

The configuration process of the Mistral is user-friendly, thanks to its intuitive web-based interface that allows for quick setup and management. Users can easily monitor network performance, manage connected devices, and customize settings to optimize connectivity based on their specific requirements.

Additionally, the Mistral Lan Router ISDN is designed with energy efficiency in mind, incorporating features that minimize power consumption without sacrificing performance. Its compact design ensures that it fits seamlessly into any workspace, making it a practical choice for users seeking a reliable and aesthetically pleasing networking solution.

In summary, the Atlantis Land Mistral Lan Router ISDN stands out for its ISDN compatibility, advanced routing capabilities, strong security features, user-friendly setup, and energy efficiency. It serves as a comprehensive networking solution that caters to both home users and small businesses, ensuring reliable connectivity and high performance in a competitive digital landscape.
Top Page Image Contents