Asante Technologies 2072 manual Segment Control, Selecting a Slot for Segment Change

Page 40

Segment Control

Setting Segment Control This section explains how to ﬁrst select a module for a segment Manually change and then perform the actual segment change. Figure 27

summarizes the steps.

AMS LINK

OUT OF

BAND

SETUP

Select Slot buttonChange Segment button

ASANTEVIEW	SEGMENT CONTROL
OUT-OF-BAND	PRESS BOTH BUTTONS TO SET		SEG 2
TERMINATION

RS232/AMS LINK	SELECT	CHANGE	SEG 1

CONFIGURATION	SLOT	SEGMENT

Step 1. Press Select Slot button until speciﬁed slot is chosen.

Step 3. Press both the Select Slot and Change Segment buttons at the same time to set the new segment selection.

Step 2. Press Change Segment

button until speciﬁed segment is chosen.

Figure 27 Selecting a Slot for Segment Change

ΔTo ensure that you maintain network manage- ment capabilities, you must make sure that your AsantéView Management Station (AMS), which is running AsantéView management software, is on the same segment as the NMM. (Segment 1 is the default setting.)

To manually select a module for segment change, complete the following steps.

1	Press the Select Slot button.
	If the NMM is set to Segment 1, pressing the Select
	Slot Button causes the Segment 1 LED to ﬂash. If the
	NMM is set to Segment 2, pressing the Select Slot But-
	ton causes the Segment 2 LED to ﬂash. If the NMM is
	isolated (set to neither segment), pressing the Select
	Slot Button causes both segment LEDs of the NMM
	module (Seg 1 and Seg 2) to ﬂash.
2	Continue pressing the Select Slot button until you
	have chosen your speciﬁed slot.The Segment LED for

the speciﬁed slot begins ﬂashing.

Page 39

Image 40

Contents AsantéHub 2072 Network Management Module Installation Guide AsantéHub Network Management Module Installation Guide AsantéHub 2072 Network Management Module Installation Guide Asking for AssistanceTell Us What You Think Tell Us What You ThinkIntroducing Network Management Module AH2072NMMIntroducing the Network Management Module Grounding Requirements Checking Package Contents Installation Segment ControlDIP Switch Front Panel Function of NMM Front Panel ComponentsAsanteview OUT-OF Front Panel AMS Link Connecting Hubs in an Out-of-Band Daisy-Chain Cable Connections to Other DevicesCable Connections to Other Devices HubSummary of DIP Switch Settings DIP switch settings for Out-of-Band using AMS Link Connecting a Modem to the Hub ConfigurationUsing the Local Management Port RS232/AMS Link Conﬁguration DIP Switch SettingConnect a straight-through RS232 cable to the RS232 Using AsantéTerm AsantéTerm IconAsanté Remote Management System Main Menu using AsantéTerm Using Telnet Upgrading the Hub Image Code Icon for NCSA/BYU Telnet 2.5 MacintoshClick the OK button. shows the Asanté Using the Asanté Remote Management System General GuidelinesUsing the Asanté Remote Management System Asanté Remote Management System Menu TutorialExample General Conﬁguration Screen Type the password Asante the password is case-sensi Type a from the Conﬁguration menu.This takes you to Type Ofﬁce Hub 2072 or a different name if you wish Press q to return to the Conﬁguration menu Conﬁguration Menu Accessing the Conﬁguration MenuConﬁguration Menu System Administration Information Group Parameters Console Password Reset System Type c for Console Password Type the new password a second time and press An Example for Segmenting the Network Segment ControlSegment Control Selecting a Slot for Segment ChangeIsolating Modules from the Network Segment LED StatesRS232 Connections Technical SpeciﬁcationsTechnical Speciﬁcations Index IndexEeprom MIB Snmp