Multi Tech Equipment MT5634ZBA-V-V92 manual Bn Transmit Break, Kn Break Control

Page 32

MultiModemZBA-V-V92 User Guide

4 AT Commands, S-Registers, & Result Codes

 

 

 

Command:

\Bn

Transmit Break

Values:

 

n = 0–9 in 100 ms units

Default:

 

3

Description:

 

In non-error-correction mode only, sends a break signal of the

 

 

specified length to a remote modem. Works in conjunction with

 

 

the \K command.

Command:

\Kn

Break Control

Values:

 

n = 0–5

Default:

 

5

Description:

 

Controls the response of the modem to a break received from

 

 

the computer, the remote modem, or the \B commnd. The re-

 

 

sponse is different for each of three different states.

 

 

Data mode. The modem receives the break from the com-

 

 

puter:

 

\K0

Enters online command mode, no break sent to the remote

 

 

modem.

 

\K1

Clears data buffers and send break to the remote modem.

 

\K2

Same as \K0.

 

\K3

Sends break immediately to the remote modem .

 

\K4

Same as \K0.

 

\K5

Sends break to the remote modem in sequence with the trans-

 

 

mitted data.

 

 

Data mode. The modem receives the break from the remote

 

 

modem:

 

\K0

Clears data buffers and sends break to the computer.

 

\K1

Same as \K0.

 

\K2

Sends break immediately to the computer.

 

\K3

Same as \K2.

 

\K4

Sends break to the computer in sequence with the received data.

 

\K5

Same as \K4.

 

 

Online command mode. The modem receives a \Bn com-

 

 

mand from the computer:

 

\K0

Clears data buffers and sends break to the remote modem.

 

\K1

Same as \K0.

 

\K2

Sends break immediately to the remote modem.

 

\K3

Same as \K2.

 

\K4

Sends break to the remote modem in sequence with the

 

 

transmitted data.

 

\K5

Same as \K4.

27

Page 31 Page 33
Image 32
Page 31 Page 33
Contents MT5634ZBA-V-V92 Record of Revisions Table of Contents AT Commands, S-Registers, and Result Codes Introduction Upgrade Overview Chapter Introduction Product Description MultiModemZBA-V-V92 User Guide IntroductionWe Supply You SupplyChapter Installation Mount the Feet Safety WarningsMultiModemZBA-V-V92 User Guide Installation Change the Internal Jumpers Opening the ModemMultiModemZBA-V-V92 User Guide2 Installation Location of the JumpersChanging the Dial-Up/Leased-Line Jumpers Changing the Voice JumperConnect the Two-Wire Leased Line Connect the Modem to Your SystemConnect the Modem to You PC Connect the Modem to the Telephone LineConnect the Modem to the AC Power Outlet Connect the Modem to a Phone OptionalConnect a Microphone and/or Speakers Optional Connect the MicrophoneInstall the Modem Driver Power-On TestInstalling the Modem Driver Surge Protectors and LightningConfigure the Modem for Your Country Using the Global Wizard to Configure Your ModemUsing AT Commands to Configure Your Modem Click Initial Setup and Country SelectionInstall and Configure Your Software Chapter Operation Front Panel MultiModemZBA-V-V92 User Guide OperationConfiguring the Modem PhoneTools FeaturesSetup Leased Line OperationConnecting to the Internet OperationDial-Up Networking Sending a FaxChapter ATCommands,S-Registers,and ResultCodes AT Commands Repeat Last CommandCommunication Standard Setting AnswerEcho Command Mode Characters Number ATDT1028806127853500$123456789DS=n Dial Stored Telephone Number Echo Online Data CharactersMonitor Speaker Mode Return Online to Data ModeResult Codes Enable/Disable Modulation HandshakeModem Reset Tone DialingResult Code Format Result Code OptionsLoad Factory Settings Asynchronous Communications ModeData Terminal Ready DTR Control XON/XOFF Pacing ControlTest Commands Display Current SettingsStore Current Configuration Store Dialing Command\Bn Transmit Break \Kn Break Control\Nn Error Correction Mode Selection \Tn Inactivity Timer\Qn Flow Control Selection \V n Protocol Result CodeAdaptive Answer Result Code Enable DC n AT Command ControlData Calling Tone View Numbers in BlacklistDirect Connect Enable Cisco ConfigurationCommand Speed Response $Dn DTR DialingData Compression Reporting Command +DCS=x,y Select V.44 Data CompressionCommand +DS44=n V.44 Data Compression Enable Synchronous Buffered Mode SubparametersModulation Selection ModCommand +PCW= n Call Waiting Enable Mod value Valid maxrate values bpsModem on Hold Enable Command +PMHR=n Modem on Hold InitiatePCM Upstream Ignore Modem Hook FlashS109 Command +PMHT=n Modem on Hold TimerQuick Connect Control Command +VCID=n Caller ID Selection Command +VDR=x, y Distinctive Ring ReportCommand #CBDn Callback Delay Callback AttemptsCommand #CBF? Callback Failed Attempts Display Command #CBFR Callback Failed Attempts Reset#CBIn Local Callback Inactivity Timer Command #CBNy=x Store Callback Password#Sx Enter Setup Password #S=x Store Setup PasswordCommand +++ATCR Escape Sequence Command %%%ATCR Remote Configuration Escape SequenceRegisters S38 Value RateS42 S48S89 S108Result Codes Terse Verbose DescriptionBlacklist Full Remote Configuration Basic Procedure SetupTo Change the Setup Password MultiModemZBA-V-V92 User Guide Remote ConfigurationTo Change the Remote Escape Character Callback Security CallbackSecurity MultiModemZBA-V-V92 User Guide Callback SecurityTo Turn Callback Security On and Off To Set the Parity of the Callback Security MessagesTo Assign Callback Passwords and Phone Numbers Calling Procedures Password-Only CallbackPassword Number-Entry CallbackExtension-Entry Callback Callback Security Commands Command #CBD n Callback DelayCommand #CBIn Local Callback Inactivity Timer #S x Enter Setup Password #S= x Store Setup PasswordCommand &Zy=+-x,???Store Dialing Command DT, or DP. Example AT&Z0=+-ATM0D5551212,???Callback Assignments Form MultiModemZBA-V-V92 User Guide6 Callback SecurityModem on Hold Operation MultiModemZBA-V-V92 User Guide Modem on Hold Operation What Is Modem on Hold?Modem on Hold Program Modem on Hold Settings Disable Modem on HoldEnable Modem on Hold Enable Caller IDExit MTMoh Check Modem StatusAbout MTMoh Using Modem on Hold Answering a Voice CallResuming a Data Call Solving Problems None of the Indicators Light MultiModemZBA-V-V92 User Guide Solving ProblemsModem Does Not Respond to Commands Modem Cannot Connect When Dialing Modem Disconnects While Online Data Is Being Lost Modem Cannot Connect When AnsweringFile Transfer Is Slower Than It Should Be Fax and Data Software Can’t Run at the Same Time There Are Garbage Characters on the MonitorModem Doesn’t Work with Caller ID Appendixes FCC Part 68 Telecom MultiModemZBA-V-V92 User Guide Regulatory ComplianceFCC Part Fax Branding StatementInternational Modem Restrictions Canadian Limitations NoticeIndustry Canada EMC, Safety, and R&TTE Directive Compliance New Zealand Telecom Warning NoticeSouth African Notice MultiModemZBA-V-V92 User Guide Technical Specifications Error CorrectionMode of Operation Intelligent FeaturesCommand Buffer ConnectorsDiagnostics IndicatorsIdentify the Modem Firmware Upgrade OverviewIntroduction Download the Upgrade File Extract the Upgrade FilesIdentify the Current Firmware Version Clear Your Stored ParametersUpgrade the Modem’s Firmware Restore Your ParametersStandard Linux Serial Port Definitions InstallationUsing the Terminal Program Minicom to Verify Operation Using the Modem to Call the Internet Select Dialup Configuration ToolCalling the ISP Answering CallsConnecting to a Cisco Router Console Port Configure the Modem for your CountryConfigure for Callback Security in Direct Connect Mode MultiModemZBA-V-V92 User Guide Connecting to a Cisco RouterConsole Port Final Setup Remote Configuration Signal RJ-45 pin DB-9 pin DB-25 pinConsole Port Connections Cable Pin-outs and Cabling Guide Console ModemMultiModemZBA-V-V92 User Guide Connecting to a Cisco Router Repair Procedures for U.S. and Canadian Customers Multi-Tech Systems, Inc. Warranty & Repairs PoliciesWarranty Repair Procedures for International Distributors Online Warranty Registration Service Canadian CustomersInternational Customers outside U.S.A. and Canada Attn Repairs, Serial #Replacement Parts Technical SupportInternet Sites International DistributorsIndex Index 103 MultiModemZBA-V-V92 User Guide Index104

MT5634ZBA-V-V92 specifications

The Multi Tech Equipment MT5634ZBA-V-V92 is a versatile and reliable modem designed for various data communication applications. As a part of the MultiTech line of products, this modem is engineered to provide seamless connectivity in both dial-up and broadband environments. Its robust feature set ensures compatibility with a wide array of devices, making it a great choice for businesses and individuals alike.

One of the main features of the MT5634ZBA-V-V92 is its ability to operate at V.92 speeds, allowing for data transmission rates of up to 56 Kbps. This makes it suitable for sending and receiving large amounts of data quickly, a significant advantage for businesses that require efficient communication. The modem is also backward compatible with previous V.90 technologies, ensuring that it can connect with older systems without any issues.

Another notable aspect of the MT5634ZBA-V-V92 is its built-in error correction and data compression capabilities. These technologies significantly enhance data integrity and transmission speed, resulting in fewer dropped connections and faster downloads. The modem uses state-of-the-art compression algorithms to optimize data flow, making it ideal for applications that require reliable and swift data exchange.

In terms of connectivity, the MT5634ZBA-V-V92 supports various interfaces, including RS-232, which allows for easy integration with a wide range of computer systems and other devices. Its flexibility in interfacing options makes it suitable for diverse environments, from industrial applications to home office setups.

The modem's design is also focused on user-friendliness. It comes equipped with LED indicators that provide real-time status updates on power, data transmission, and network connection, allowing users to monitor their connections effortlessly. Additionally, the device includes a simple installation process, which minimizes downtime and helps users get up and running quickly.

The MT5634ZBA-V-V92 is built to last, with a sturdy construction that ensures durability in demanding conditions. Its compact design allows for easy mounting and placement, making it an excellent choice for both stationary and mobile applications.

Overall, the Multi Tech Equipment MT5634ZBA-V-V92 is a powerful modem that merges speed, reliability, and flexibility. With its advanced features and technologies, it stands out as a dependable solution for anyone in need of high-performance data communication. Whether for business or personal use, this modem meets the connectivity needs of today's digital landscape with ease.
Top Page Image Contents