Multi Tech Equipment MT5634ZBA-V-V92 manual Tone Dialing, Result Code Format, Result Code Options

Page 29

MultiModemZBA-V-V92 User Guide

4 AT Commands, S-Registers, & Result Codes

 

 

 

Command:

T

Tone Dialing

Values:

 

P, T

Default:

 

T

Description:

 

Configures the modem for DTMF (touch-tone) dialing. Dialed

 

 

digits are tone dialed until a P command or dial modifier is re-

 

 

ceived.

Command:

Vn

Result Code Format

Values:

 

n = 0 or 1

Default:

 

1

Description:

V0

Displays result codes as digits (terse response).

 

V1

Displays result codes as words (verbose response).

Command:

Wn

Result Code Options

Values:

 

n = 0, 1, 2

Default:

 

2

Description:

W0

CONNECT result code reports serial port speed, disables

 

 

protocol result codes.

 

W1

CONNECT result code reports serial port speed, enables

 

 

protocol result codes.

 

W2

CONNECT result code reports line speed, enables protocol

 

 

result codes.

Command:

Xn

Result Code Selection

Values:

 

n = 0–7

Default:

 

4

Description:

X0

Basic result codes (e.g., CONNECT); does not look for dial

 

 

tone or busy signal.

 

X1

Extended result codes (e.g., CONNECT 46000 V42bis); does

 

 

not look for dial tone or busy signal.

 

X2

Extended result codes with NO DIALTONE; does not look for

 

 

busy signal.

 

X3

Extended result codes with BUSY; does not look for dial tone.

 

X4

Extended result codes with NO DIALTONE and BUSY.

 

X5

Extended result codes with NO DIALTONE and BUSY.

 

X6

Extended result codes with NO DIALTONE and BUSY.

 

X7

Basic result codes with NO DIALTONE and BUSY.

Command:

Zn

Modem Reset

Values:

 

n = 0 or 1

Default:

 

None

Description:

Z0

Resets modem to profile saved by the last &W command.

 

Z1

Same as Z0.

Command:

&Cn

Data Carrier Detect (DCD) Control

Values:

 

n = 0, 1, or 2

Default:

 

1

Description:

&C0

Forces the DCD circuit to be always high.

 

&C1

DCD goes high when the remote modem’s carrier signal is

 

 

detected, and goes low when the carrier signal is not detected.

 

&C2

DCD drops on disconnect for time set by S18, then goes high

 

 

again (for some CBX phone systems).

24

Page 28 Page 30
Image 29
Page 28 Page 30
Contents MT5634ZBA-V-V92 Record of Revisions Table of Contents AT Commands, S-Registers, and Result Codes Introduction Upgrade Overview Chapter Introduction MultiModemZBA-V-V92 User Guide Introduction Product DescriptionYou Supply We SupplyChapter Installation Mount the Feet Safety WarningsMultiModemZBA-V-V92 User Guide Installation Opening the Modem Change the Internal JumpersLocation of the Jumpers MultiModemZBA-V-V92 User Guide2 InstallationChanging the Dial-Up/Leased-Line Jumpers Changing the Voice JumperConnect the Modem to Your System Connect the Two-Wire Leased LineConnect the Modem to You PC Connect the Modem to the Telephone LineConnect the Modem to a Phone Optional Connect the Modem to the AC Power OutletConnect a Microphone and/or Speakers Optional Connect the MicrophonePower-On Test Install the Modem DriverInstalling the Modem Driver Surge Protectors and LightningUsing the Global Wizard to Configure Your Modem Configure the Modem for Your CountryUsing AT Commands to Configure Your Modem Click Initial Setup and Country SelectionInstall and Configure Your Software Chapter Operation MultiModemZBA-V-V92 User Guide Operation Front PanelPhoneTools Features Configuring the ModemLeased Line Operation SetupOperation Connecting to the InternetSending a Fax Dial-Up NetworkingChapter ATCommands,S-Registers,and ResultCodes Repeat Last Command AT CommandsCommunication Standard Setting AnswerNumber ATDT1028806127853500$123456789 Echo Command Mode CharactersDS=n Dial Stored Telephone Number Echo Online Data CharactersReturn Online to Data Mode Monitor Speaker ModeResult Codes Enable/Disable Modulation HandshakeTone Dialing Modem ResetResult Code Format Result Code OptionsAsynchronous Communications Mode Load Factory SettingsData Terminal Ready DTR Control XON/XOFF Pacing ControlDisplay Current Settings Test CommandsStore Current Configuration Store Dialing Command\Kn Break Control \Bn Transmit Break\Tn Inactivity Timer \Nn Error Correction Mode Selection\Qn Flow Control Selection \V n Protocol Result CodeDC n AT Command Control Adaptive Answer Result Code EnableData Calling Tone View Numbers in BlacklistCisco Configuration Direct Connect EnableCommand Speed Response $Dn DTR DialingData Compression Reporting Command +DCS=x,y Select V.44 Data CompressionCommand +DS44=n V.44 Data Compression Subparameters Enable Synchronous Buffered ModeMod Modulation SelectionMod value Valid maxrate values bps Command +PCW= n Call Waiting EnableCommand +PMHR=n Modem on Hold Initiate Modem on Hold EnablePCM Upstream Ignore Modem Hook FlashS109 Command +PMHT=n Modem on Hold TimerQuick Connect Control Command +VDR=x, y Distinctive Ring Report Command +VCID=n Caller ID SelectionCommand #CBDn Callback Delay Callback AttemptsCommand #CBFR Callback Failed Attempts Reset Command #CBF? Callback Failed Attempts Display#CBIn Local Callback Inactivity Timer Command #CBNy=x Store Callback Password#S=x Store Setup Password #Sx Enter Setup PasswordCommand +++ATCR Escape Sequence Command %%%ATCR Remote Configuration Escape SequenceRegisters Value Rate S38S48 S42S89 S108Terse Verbose Description Result CodesBlacklist Full Remote Configuration Setup Basic ProcedureTo Change the Setup Password MultiModemZBA-V-V92 User Guide Remote ConfigurationTo Change the Remote Escape Character Callback Security MultiModemZBA-V-V92 User Guide Callback Security CallbackSecurityTo Set the Parity of the Callback Security Messages To Turn Callback Security On and OffTo Assign Callback Passwords and Phone Numbers Password-Only Callback Calling ProceduresPassword Number-Entry CallbackExtension-Entry Callback Command #CBD n Callback Delay Callback Security CommandsCommand #CBIn Local Callback Inactivity Timer #S= x Store Setup Password #S x Enter Setup PasswordDT, or DP. Example AT&Z0=+-ATM0D5551212,??? Command &Zy=+-x,???Store Dialing CommandMultiModemZBA-V-V92 User Guide6 Callback Security Callback Assignments FormModem on Hold Operation MultiModemZBA-V-V92 User Guide Modem on Hold Operation What Is Modem on Hold?Modem on Hold Program Disable Modem on Hold Modem on Hold SettingsEnable Modem on Hold Enable Caller IDExit MTMoh Check Modem StatusAbout MTMoh Answering a Voice Call Using Modem on HoldResuming a Data Call Solving Problems MultiModemZBA-V-V92 User Guide Solving Problems None of the Indicators LightModem Does Not Respond to Commands Modem Cannot Connect When Dialing Modem Disconnects While Online Data Is Being Lost Modem Cannot Connect When AnsweringFile Transfer Is Slower Than It Should Be Fax and Data Software Can’t Run at the Same Time There Are Garbage Characters on the MonitorModem Doesn’t Work with Caller ID Appendixes MultiModemZBA-V-V92 User Guide Regulatory Compliance FCC Part 68 TelecomFax Branding Statement FCC PartInternational Modem Restrictions Canadian Limitations NoticeIndustry Canada New Zealand Telecom Warning Notice EMC, Safety, and R&TTE Directive ComplianceSouth African Notice Error Correction MultiModemZBA-V-V92 User Guide Technical SpecificationsMode of Operation Intelligent FeaturesConnectors Command BufferDiagnostics IndicatorsIdentify the Modem Firmware Upgrade OverviewIntroduction Extract the Upgrade Files Download the Upgrade FileIdentify the Current Firmware Version Clear Your Stored ParametersRestore Your Parameters Upgrade the Modem’s FirmwareStandard Linux Serial Port Definitions InstallationUsing the Terminal Program Minicom to Verify Operation Select Dialup Configuration Tool Using the Modem to Call the InternetCalling the ISP Answering CallsConfigure the Modem for your Country Connecting to a Cisco Router Console PortConfigure for Callback Security in Direct Connect Mode MultiModemZBA-V-V92 User Guide Connecting to a Cisco RouterConsole Port Final Setup Signal RJ-45 pin DB-9 pin DB-25 pin Remote ConfigurationConsole Port Connections Cable Pin-outs and Cabling Guide Console ModemMultiModemZBA-V-V92 User Guide Connecting to a Cisco Router Repair Procedures for U.S. and Canadian Customers Multi-Tech Systems, Inc. Warranty & Repairs PoliciesWarranty Repair Procedures for International Distributors Canadian Customers Online Warranty Registration ServiceInternational Customers outside U.S.A. and Canada Attn Repairs, Serial #Technical Support Replacement PartsInternet Sites International DistributorsIndex Index MultiModemZBA-V-V92 User Guide Index 103104

MT5634ZBA-V-V92 specifications

The Multi Tech Equipment MT5634ZBA-V-V92 is a versatile and reliable modem designed for various data communication applications. As a part of the MultiTech line of products, this modem is engineered to provide seamless connectivity in both dial-up and broadband environments. Its robust feature set ensures compatibility with a wide array of devices, making it a great choice for businesses and individuals alike.

One of the main features of the MT5634ZBA-V-V92 is its ability to operate at V.92 speeds, allowing for data transmission rates of up to 56 Kbps. This makes it suitable for sending and receiving large amounts of data quickly, a significant advantage for businesses that require efficient communication. The modem is also backward compatible with previous V.90 technologies, ensuring that it can connect with older systems without any issues.

Another notable aspect of the MT5634ZBA-V-V92 is its built-in error correction and data compression capabilities. These technologies significantly enhance data integrity and transmission speed, resulting in fewer dropped connections and faster downloads. The modem uses state-of-the-art compression algorithms to optimize data flow, making it ideal for applications that require reliable and swift data exchange.

In terms of connectivity, the MT5634ZBA-V-V92 supports various interfaces, including RS-232, which allows for easy integration with a wide range of computer systems and other devices. Its flexibility in interfacing options makes it suitable for diverse environments, from industrial applications to home office setups.

The modem's design is also focused on user-friendliness. It comes equipped with LED indicators that provide real-time status updates on power, data transmission, and network connection, allowing users to monitor their connections effortlessly. Additionally, the device includes a simple installation process, which minimizes downtime and helps users get up and running quickly.

The MT5634ZBA-V-V92 is built to last, with a sturdy construction that ensures durability in demanding conditions. Its compact design allows for easy mounting and placement, making it an excellent choice for both stationary and mobile applications.

Overall, the Multi Tech Equipment MT5634ZBA-V-V92 is a powerful modem that merges speed, reliability, and flexibility. With its advanced features and technologies, it stands out as a dependable solution for anyone in need of high-performance data communication. Whether for business or personal use, this modem meets the connectivity needs of today's digital landscape with ease.
Top Page Image Contents