American Telecom AM64/128A manual Status Menu, Over all Status, Loop Active

Page 14

Status Menu	AM64/128A User Manual

5.3Status Menu

The status menu is read only, which means the select button has no effect. It provides the following data:

(1)Overall status

(2)Alarm messages

(3)User data rate

(4)Line rate

(5)Interface status

(6)Operating mode

5.3.1Over all Status

The possible messages for this item in priority order, and the conditions which set them are as follows:

S > Loop Active

S > LTU Not Ready

S > LTU Ready

S > Data Transfer

S > Send Data

S > Receive Data

(a) If a loop is applied within the BBM the display reads:

S > Loop Active

(b)If a fault exists or a not ready signal (including AIS) is being received from line then the display reads:

S > LTU Not Ready

(c)Status from line (I or 109) is on, DTE status (C or 105/108) is off, the display is: S > Receive Data

(d) Status from the DTE is on, status received from line is off, the display is:

S > Send Data

(e) If both status lines are off then the display reads:

S > LTU Ready

(f) If both status lines are on then the display is:

S > Data Transfer

Note: If the user rate has no relevant status line (rates 16k, 32k, 64k or X.50), then (c), (d), and (f) are displayed as per (e).

14

Image 14

Contents ATL Part No /203/002/610 Issue 4 September Base Band ModemInformation Contained This Document is Confidential to Contents Appendix B Introduction International ModelsInterface Modules Constructional DetailsBaseband Modems System Overview System Overview BBM to BBM Link InstallationTesting Self Test PassLTU Ready No Alarm LTU Not Ready Link ModeNetwork Mode BBM to Line Card LinkFront Panel Features Menu OperationLoop back Off Loop back OnLoop Active Status MenuOver all Status LOS/CD Fail Alarm StatusNo Alarm No Signal Receiving AIS No Alignment CD FailInterface Status User RateLine Rate Operating Mode Link Mode Network ModeLocal loop from menu Top level display shows Loc Loop Off Test MenuLocal loop Loc Loop OnLoopback is applied by selecting the display Loopback Off LoopbackLocal loop from DTE Loopback OnRem Loop Off Remote LoopRemote Loop from menu Rem Loop OnBin Keys Off Sending Bin Binary PatternsRemote loop from DTE Overview Error Count Bit Error Rate BER = User Data Rate x TimeData Test OperationErrors Errors nnnnnnErrors s000001 Data TestInjecting 0s Injection ModeTransparent Mode Injecting 1sComms Evp Rx Evp Tx Service TestSvc Test Time If the count is stopped the display is StopLamp Test Self TestCommunication Channel Loopback Comm Loop OffRate Menu Rate 4.8KMaster 64K BT Slave 4.8K Option Menu 2 X.21bis3 G.703 Asynchronous ModeSignalling Rate Character Length Char LenLine Rate Configuration MenuMaster Slave Synchronisation Type for software versions below 3 X.21 Loop ControlModem Ext Bit Clk Synchronisation Type for software version V1.3 and aboveExt Byte Clk Internal ClkMenu Lock 5 64k ModePower Level Glossary of Terms Band circuits General Specifications Appendix a Interface Pin Connections Way D type X.21 bis V.24 / V.28* Connector pin allocationWay D-type X.21 V.11 Connector pin allocation Mrac Connector Pin allocation Way D-type V.36 Connector pin allocationWay D-type RS-530 Connector pin allocation Line ConnectorAppendix B Internal Link Settings Page Interface Modules Interface ModuleRS530 Interface Module 21bis Interface ModuleService Test Facilities Frame StructureAppendix C In Service Test LVD Safety Statements TTE Network and Safety statementsAppendix E 21 bit timing cable 15 way to 15 way D type plugs35 bit timing cable 34 way to 34 way Mrac plugs 21 byte timing cable 15 way to 15 way D type plugs24 / V.28 bit timing cable 25 way to 25 way D type plugs 21 bis V.36 bit timing cable 37 way to 37 way D type plugs RS530 bit timing cable 25 way to 25 way D type plugsAppendix F Troubleshooting Master Mode C 64K Rate Slave Mode 64K RatePower 10dBm Rate 64K