Sony CPD-300SFT manual Adjustments, Adjusting the Picture Contrast

Page 6

Adjustments

When one of the preset-type signals is input, no picture adjustment is necessary.

You can, however, adjust the picture to your preferences by the following procedure described below.

You can adjust all the items on the OSD (On Screen Display). The item to be adjusted is indicated in white on the OSD.

Control Panel

pBefore adjusting the items, turn on the unit and feed the video signal from the connected computer/work station.

pAdjustments will be stored automatically.

					POWER
RESET	COLOR	CONV	GEOM	SIZE	SAVING
					CENTER

Adjusting the Picture Brightness

Adjusting the Picture Centering

The adjustment data becomes the common setting for all input signals.

1 Press the ¬ ?//button.

The “BRIGHTNESS/CONTRAST” OSD (On Screen Display) appears.

BRIGHTNESS/CONTRAST

230

80 . 0kHz/75Hz

Horizontal Vertical frequency∗ frequency∗

2 Press the ¬?//buttons to adjust picture brightness.

?. . . for less brightness /. . . for more brightness

The “BRIGHTNESS/CONTRAST” OSD disappears 3 seconds after you release the buttons.

To reset, press RESET button while the OSD is on.

Adjusting the Picture Contrast

The adjustment data becomes the common setting for all input signals.

1 Press the > >/.button.

The “BRIGHTNESS/CONTRAST” OSD (On Screen Display) appears.

BRIGHTNESS/CONTRAST

230

80 . 0kHz/75Hz

Horizontal Vertical frequency∗ frequency∗

2 Press the > >/.buttons to adjust picture contrast.

>. . . for more contrast

.. . . for less contrast

The “BRIGHTNESS/CONTRAST” OSD disappears 3 seconds after you release the buttons.

To reset, press RESET button while the OSD is on.

The adjustment data becomes the individual setting for each input signal received.

1 Press the CENTER button.

The “CENTER” OSD (On Screen Display) appears.

CENTER

CENTER

023

2 For vertical picture adjustment Press the > >/.buttons.

>. . . to move up

.. . . to move down

For horizontal picture adjustment

Press the ¬ ?//buttons.

?. . . to move left /. . . to move right

To erase the “CENTER” OSD, press the CENTER button again. The “CENTER” OSD automatically disappears 10 seconds after you release the buttons.

To reset, press RESET button while the OSD is on.

∗The horizontal and vertical frequencies for each input signal received appear on the “BRIGHTNESS/CONTRAST” OSD.

6

Image 6

Contents Multiscan300sf Owner’s Record Table of Contents PrecautionsIntroduction For the customers using the Windows 4 Getting StartedUsing Your Monitor Preset and User ModesRecommended horizontal timing conditions Adjustments Adjusting the Picture ContrastAdjusting the Picture Rotation Adjusting the Picture SizeAdjusting the Pincushion For vertical picture adjustmentFor vertical adjustment Press the /.buttons Adjustments Adjusting the ConvergenceSetting the Color Temperature For horizontal adjustmentSwitching the Input Connector Resetting the Adjustment Data to Factory-preset LevelsEntering New Timings Power Saving FunctionDamper Wire Plug and PlayVideo input 1 connector HD15 Female SpecificationsTroubleshooting Pin assignmentTroubleshooting Précautions InstallationEntretienTable des matières Avertissement raccordement électriquePour les utilisateurs de Windows 4 PréparationRemarques Vers la sortie vidéoUtilisation de votre moniteur Modes par défaut et utilisateurConditions de synchronisation horizontale préconisées Réglages Réglage du centrage de l’imageRéglage du contraste de l’image Réglage de la distorsion en coussin Réglage de la taille de l’imageRéglage de la rotation de l’image Pour le réglage de la taille horizontaleRéglages Réglage de la convergence Réglage de la température des couleursPour sélectionner une température de 9300K, 6500K ou 5000K Sélection du connecteur d‘entrée Restauration des valeurs par défaut d’usineEconomies d’énergie Introduction de nouvelles synchronisationsUn moniteur prêt à l’emploi Utilisation du support pivotantAttribution des broches SpécificationsDépannage Pas d’imageDépannage Precauciones IndiceIntroducción InstalaciónMantenimientoPara los clientes con Windows 4 Procedimientos InicialesNotas NotaUso del monitor Modos predefinidos y de usuarioCondiciones recomendadas de sincronización horizontal Ajuste del contraste de la imagen AjustesAjuste del brillo de la imagen Ajuste de la posición de centrado de la imagenAjuste de la distorsión de imagen Ajuste del tamaño de la imagenAjuste de la rotación de la imagen Para realizar el ajuste vertical Pulse los botonesAjustes Ajuste de la convergencia Ajuste de la temperatura del colorPara seleccionar 9300K, 6500K o 5000K Conmutación del conector de entrada Restauración de los valores predefinidos de fábricaFunción Plug and Play Introducción de nuevos valoresFunción de ahorro de energía Soporte basculante giratorioAsignación de terminales Solución de problemasEspecificaciones Conector de entrada de vídeo HD15 HembaSolución de problemas