National Instruments WAP-3701, WAP-3711 user manual Configuring TCP/IP-related Settings, Addressing

Page 24


	NI WAP-3701/3711 User’s Manual		Web Console Configuration

	TIP	If you want to back up or restore the configuration from a remote location over the Internet,
		adjust the Timeout and Max no. of retries settings of TFTP Server for remote TFTP

configuration backup/restore to succeed.

Resetting the Configuration to Factory Defaults

Clicking the Reset button resets the device configuration to factory defaults.

WARNING

Think twice before clicking the Reset button. Doing so will cause you to lose all of your current configuration settings.

Configuring TCP/IP-related Settings

Addressing

The IP address of the AP can be set manually (Set Manually) or automatically assigned by a DHCP server on the LAN (Obtain from a DHCP Server). If you are manually setting the IP address, Subnet mask, and Default gateway settings, set them appropriately, so that they comply with your LAN environment. In addition, you can specify the Host name and Domain (DNS suffix) of the NI WAP-3701/3711.

3-10

Image 24

Contents NI WAP-3701/3711 User’s Manual First Edition, SeptCopyright Notice TrademarksDisclaimer Table of Contents Page Introduction Package Checklist Product FeaturesProduct Specifications OverviewSoftware Features PowerInterface Mechanical‰ Confirming the Settings of the AP and Client Computers Getting StartedFirst-Time Installation and Configuration NI WAP-3701/3711 User’s Manual Getting StartedAP/Bridge AP ClientConfigure the NI WAP-3701/3711’s Ieee 802.11 settings Review and Apply SettingsDeploying the Access Point AP Setting up Client ComputersConfiguring Ieee 802.11g-related Settings To establish a wireless link to an Access PointConfirming the Settings of the AP and Client Computers Configuring TCP/IP-related SettingsChecking if the Ieee 802.11g-related Settings Work Checking if the TCP/IP-related Settings WorkNI WAP-3701/3711 User’s Manual Getting Started Web Console Configuration NI WAP-3701/3711 User’s Manual Web Console Configuration Menu StructureSave, Save & Restart, and Cancel Buttons Associated Wireless ClientsViewing Status Home and Refresh ButtonsLink Monitor AP Client mode only Current Dhcp MappingsSystem Log Specifying the Operational Mode General OperationsSTA-AP WDSAdministrative Password Managing the FirmwareUpgrading the Firmware by Http Backing up and Restoring Configuration Settings by Http Upgrading Firmware by TftpChoose Tftp as the Firmware management protocol Backing up and Restoring Configuration Settings by Tftp Configuring TCP/IP-related Settings Resetting the Configuration to Factory DefaultsAddressing Dhcp Server AP/Bridge modes only BasicStatic Dhcp Mappings Configuring Ieee 802.11g-related Settings CommunicationLink Integrity Wireless Distribution System Association ControlAP Load Balancing Sample wireless bridge network topology Security Network topology containing a loopSTA Shared Key , and Auto MAC-Address-Based Access Control Set the Access control type to exclusiveSet the Access control type to inclusive Ieee 802.1X/RADIUS AP mode only Click DownloadInternet Ieee 802.1X and RadiusConfiguring Advanced Settings Packet FiltersEthernet Type Filters IP Protocol FiltersManagement TCP/UDP Port FiltersUPnP System LogSnmp Default Settings NI WAP-3701/3711 User’s Manual Default Settings LAN InterfaceManagement Snmp read communityTroubleshooting Wireless Settings ProblemsTCP/IP Settings Problems NI WAP-3701/3711 User’s Manual TroubleshootingAP does not respond to ping from the client computer Unknown Problems Wireless Router/AP BrowserNI WAP-3701/3711 User’s Manual Troubleshooting Regulatory Statement Federal Communication Commission Interference StatementTTE Compliance Statement Safety NI WAP-3701/3711 User’s Manual Regulatory StatementTechnical Support and Professional Services Worldwide Technical Support and Product Information National Instruments Corporate HeadquartersWorldwide Offices