National Instruments WAP-3701, WAP-3711 user manual Default Settings

Page 38

A

Default Settings

TIP	Press the Reset (SF-Reset, or Soft-Reset) switch on the housing of a powered-onAP to reset the
	configuration settings to factory-default values.


	Setting Name	Default Value
	Global
	User Name	admin
	Password	root
	IEEE 802.11g
	Regulatory Domain	FCC (U.S.) or ETSI (Europe)
	Channel Number	11 for FCC or 13 for ETSI
	SSID	NI
	SSID Broadcasts	Enabled
	Transmission Rate	Auto
	Transmit Power	100%
	MAC Address	See the label on the accompanying PCMCIA card
		or the label on the housing of the NI
		WAP-3701/3711.
	Security Mode	Open System
	Selected WEP Key	Key #1
	WEP Key #1	00-00-00-00-00
	WEP Key #2	00-00-00-00-00
	WEP Key #3	00-00-00-00-00
	WEP Key #4	00-00-00-00-00
	MAC-Address-Based Access Control	Disabled
	Access Control Table Type	Inclusive
	Wireless Client Isolation	Disabled
	AP Load balancing	Disabled
	Link Integrity	Disabled
	Association Control
	Max Number of Clients	64
	Block Clients if Traffic Load Exceeds	Disabled

Image 38

Contents NI WAP-3701/3711 User’s Manual First Edition, SeptDisclaimer Copyright NoticeTrademarks Table of Contents Page Introduction Product Specifications Package ChecklistProduct Features OverviewInterface Software FeaturesPower Mechanical‰ Confirming the Settings of the AP and Client Computers Getting StartedFirst-Time Installation and Configuration NI WAP-3701/3711 User’s Manual Getting StartedAP/Bridge AP ClientConfigure the NI WAP-3701/3711’s Ieee 802.11 settings Review and Apply SettingsConfiguring Ieee 802.11g-related Settings Deploying the Access Point APSetting up Client Computers To establish a wireless link to an Access PointChecking if the Ieee 802.11g-related Settings Work Confirming the Settings of the AP and Client ComputersConfiguring TCP/IP-related Settings Checking if the TCP/IP-related Settings WorkNI WAP-3701/3711 User’s Manual Getting Started Web Console Configuration NI WAP-3701/3711 User’s Manual Web Console Configuration Menu StructureViewing Status Save, Save & Restart, and Cancel ButtonsAssociated Wireless Clients Home and Refresh ButtonsSystem Log Link Monitor AP Client mode onlyCurrent Dhcp Mappings STA-AP Specifying the Operational ModeGeneral Operations WDSUpgrading the Firmware by Http Administrative PasswordManaging the Firmware Backing up and Restoring Configuration Settings by Http Upgrading Firmware by TftpChoose Tftp as the Firmware management protocol Backing up and Restoring Configuration Settings by Tftp Addressing Configuring TCP/IP-related SettingsResetting the Configuration to Factory Defaults Static Dhcp Mappings Dhcp Server AP/Bridge modes onlyBasic Link Integrity Configuring Ieee 802.11g-related SettingsCommunication AP Load Balancing Wireless Distribution SystemAssociation Control Sample wireless bridge network topology Security Network topology containing a loopSTA Shared Key , and Auto Set the Access control type to inclusive MAC-Address-Based Access ControlSet the Access control type to exclusive Ieee 802.1X/RADIUS AP mode only Click DownloadInternet Ieee 802.1X and RadiusEthernet Type Filters Configuring Advanced SettingsPacket Filters IP Protocol FiltersUPnP ManagementTCP/UDP Port Filters System LogSnmp Default Settings Management NI WAP-3701/3711 User’s Manual Default SettingsLAN Interface Snmp read communityTroubleshooting Wireless Settings ProblemsAP does not respond to ping from the client computer TCP/IP Settings ProblemsNI WAP-3701/3711 User’s Manual Troubleshooting Unknown Problems Wireless Router/AP BrowserNI WAP-3701/3711 User’s Manual Troubleshooting TTE Compliance Statement Regulatory StatementFederal Communication Commission Interference Statement Safety NI WAP-3701/3711 User’s Manual Regulatory StatementTechnical Support and Professional Services Worldwide Offices Worldwide Technical Support and Product InformationNational Instruments Corporate Headquarters