National Instruments WAP-3701, WAP-3711 user manual Regulatory Statement, TTE Compliance Statement

Page 44

C

Regulatory Statement

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.

yConsult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example – use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE).

The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) as of April 8,2000.

Page 43 Page 45
Image 44
Page 43 Page 45
Contents NI WAP-3701/3711 User’s Manual First Edition, SeptDisclaimer Copyright NoticeTrademarks Table of Contents Page Introduction Package Checklist Product FeaturesProduct Specifications OverviewSoftware Features PowerInterface Mechanical‰ Confirming the Settings of the AP and Client Computers Getting StartedFirst-Time Installation and Configuration NI WAP-3701/3711 User’s Manual Getting StartedAP/Bridge AP ClientConfigure the NI WAP-3701/3711’s Ieee 802.11 settings Review and Apply SettingsDeploying the Access Point AP Setting up Client ComputersConfiguring Ieee 802.11g-related Settings To establish a wireless link to an Access PointConfirming the Settings of the AP and Client Computers Configuring TCP/IP-related SettingsChecking if the Ieee 802.11g-related Settings Work Checking if the TCP/IP-related Settings WorkNI WAP-3701/3711 User’s Manual Getting Started Web Console Configuration NI WAP-3701/3711 User’s Manual Web Console Configuration Menu StructureSave, Save & Restart, and Cancel Buttons Associated Wireless ClientsViewing Status Home and Refresh ButtonsSystem Log Link Monitor AP Client mode onlyCurrent Dhcp Mappings Specifying the Operational Mode General OperationsSTA-AP WDSUpgrading the Firmware by Http Administrative PasswordManaging the Firmware Backing up and Restoring Configuration Settings by Http Upgrading Firmware by TftpChoose Tftp as the Firmware management protocol Backing up and Restoring Configuration Settings by Tftp Addressing Configuring TCP/IP-related SettingsResetting the Configuration to Factory Defaults Static Dhcp Mappings Dhcp Server AP/Bridge modes onlyBasic Link Integrity Configuring Ieee 802.11g-related SettingsCommunication AP Load Balancing Wireless Distribution SystemAssociation Control Sample wireless bridge network topology Security Network topology containing a loopSTA Shared Key , and Auto Set the Access control type to inclusive MAC-Address-Based Access ControlSet the Access control type to exclusive Ieee 802.1X/RADIUS AP mode only Click DownloadInternet Ieee 802.1X and RadiusConfiguring Advanced Settings Packet FiltersEthernet Type Filters IP Protocol FiltersManagement TCP/UDP Port FiltersUPnP System LogSnmp Default Settings NI WAP-3701/3711 User’s Manual Default Settings LAN InterfaceManagement Snmp read communityTroubleshooting Wireless Settings ProblemsAP does not respond to ping from the client computer TCP/IP Settings ProblemsNI WAP-3701/3711 User’s Manual Troubleshooting Unknown Problems Wireless Router/AP BrowserNI WAP-3701/3711 User’s Manual Troubleshooting TTE Compliance Statement Regulatory StatementFederal Communication Commission Interference Statement Safety NI WAP-3701/3711 User’s Manual Regulatory StatementTechnical Support and Professional Services Worldwide Offices Worldwide Technical Support and Product InformationNational Instruments Corporate Headquarters
Top Page Image Contents