Dell FM120x4 owner manual Hard drives/SSDs, Hard drive/SSD to node assignment

Page 40

Figure 16. Installing the memory module

 

 

1.

memory module

2.

memory-module ejectors

3.

memory-module socket alignment key

4.

memory-module alignment key

NOTE: When the memory module is properly seated in the socket, the ejectors on the memory module socket align with the ejectors on the other sockets that have memory modules installed.

7.Repeat step 4 through step 7 of this procedure to install the remaining memory modules.

8.Install the sled in the enclosure.

9.Turn on the sled.

10.(Optional) Press <F2> to enter the System Setup, and check the System Memory setting. The system should have already changed the value to reflect the newly installed memory.

NOTE: If the value is incorrect, one or more of the memory modules may not be installed properly. Check to ensure that the memory modules are firmly seated in their sockets.

11.Run the system memory test in the system diagnostics.

Hard drives/SSDs

Depending on the configuration, your system supports four 2.5 inch SATA hard drives/SSDs, or eight 1.8 inch SATA SSDs. All drives connect to the system board through the hard-drive/SSD backplane. The hard drives/SSDs are supplied in special hot-swap drive carriers that fit in the drive bays.

Hard drive/SSD to node assignment

The hard drives/SSDs are not shared resources between the nodes in the system. Each hard drive/SSD is assigned to a specific node. Depending on the configuration, the hard drives/SSDs are assigned to the nodes in the following order.

40

Image 40
Contents Regulatory Model E02B Regulatory Type E02B002 Page Contents Installing sled components Using the Boot Manager navigation keys Boot Manager screenTroubleshooting your system Using system diagnosticsJumpers and connectors Technical specificationsGetting help Terms used in the document About your systemTerm Description Front-panel features and indicators Hard-drive/SSD indicator patterns Drive-Status Indicator Pattern ConditionNode status indicators Indicator Pattern Description OffSolid blue Blinking blueUsing USB diskette or USB DVD/CD drives Documentation matrixQuick Resource Locator Setting up your system Performing initial system configurationSetting up and configuring the iDRAC IP address Logging in to iDRAC Installing the operating system Click Get drivers and downloadsUsing the System Setup and Boot Manager Choosing the system boot modeEntering System Setup System setup optionsResponding to error messages Using the System Setup navigation keysSystem Bios screen System Information screenProcessor Settings screen Memory Settings screenSata Settings screen Integrated Devices screen Boot Settings screenSerial Communications screen System Profile Settings screen Miscellaneous settings System and setup password featuresSystem Security screen Assigning a system and/or setup password Using your system password to secure your system Operating with a setup password enabledUsing the Boot Manager navigation keys Entering the Uefi Boot ManagerBoot Manager screen IDRAC Settings utility Embedded system managementNetworking configurations Entering the iDRAC Settings utilityStandard configuration System Setup Main Menu page, click iDRAC SettingsNetwork adapter isolation configuration Icon DescriptionIsolated networks configuration Network adapter isolation configurationTrunk configuration or LAG Installing sled components Removing and installing the sledRecommended tools Removing the sledInstalling the sled Removing and installing a sledInside the sled Inside the sled 2.5 inch hard-drive/SSD systemCable cover Removing the cable coverInstalling the cable cover Removing and installing the cable coverCooling shroud Removing the cooling shroudInstalling the cooling shroud System memoryDimm Type DIMMs Populated Per Maximum Dimm Rank PerGeneral memory module installation guidelines Sample memory configurationsRemoving memory modules Number Organization Dimm Slot Population DIMMs SpeedInstalling memory modules Removing the memory moduleHard drives/SSDs Hard drive/SSD to node assignmentRemoving a hard drive/SSD Hard-Drive/SSD Bay NodeHard-drive/SSD carrier handle Installing a hard drive/SSD Shutdown procedure for servicing a hard drive/SSDConfiguring the boot drive Hard-drive/SSD backplane Installing a 1.8 inch SSD in the SSD carrierRemoving a 1.8 inch SSD from the SSD carrier Removing and installing the hard-drive/SSD backplane Removing the hard-drive/SSD backplaneInstalling the hard-drive/SSD backplane SSD cage assemblyRemoving the SSD cage assembly Installing the SSD cage assembly Easy restore moduleReplacing the easy restore module System battery Replacing the system batterySystem board Removing the system boardPage Installing the system board Removing and installing the system boardControl panel Removing the control panelInstalling the control panel Removing and installing the control panelPage Troubleshooting your system Troubleshooting hard drives Troubleshooting USB devicesTroubleshooting the system board Troubleshooting the system batterySystem messages Diagnostic messagesAlert messages Using system diagnostics Dell Embedded System DiagnosticsWhen to use the Embedded System Diagnostics Running the Embedded System DiagnosticsSystem diagnostic controls Least one event description is recordedJumpers and connectors System board jumper settingsJumper Setting Description Configuration settings are retained at system bootSystem board connectors Connector DescriptionDisabling a forgotten password Technical specifications Battery Environmental Expanded operating temperatureTemperature Temperature Continuous OperationMaximum Vibration Maximum ShockMaximum Altitude Operating Altitude De-ratingGaseous Contamination Quick Resource Locator Locating your system Service Tag Getting helpContacting Dell Documentation feedback