Dell FM120x4 Installing a hard drive/SSD, Shutdown procedure for servicing a hard drive/SSD

Page 43

Figure 20. Removing and installing a 1.8 inch SSD
1.	SSD connector (on backplane)	2.	SSD
3.	SSD carrier handle	4.	release button

Installing a hard drive/SSD

CAUTION: When a replacement hot-swap hard drive/SSD is installed and the sled is powered on, the drive automatically begins to rebuild. Make absolutely sure that the replacement hard drive/SSD is blank or contains data that you wish to have over-written. Any data on the replacement hard drive/SSD is immediately lost after the drive is installed.

NOTE: Not all operating systems support hot-swap drive installation. See the documentation supplied with your operating system.

NOTE: The 2.5 inch hard-drive/SSD configuration supports four warm-swap hard-drives/SSDs. Each hard- drive/SSD is assigned to a specific node, and the node to which it is assigned must be turned off before servicing the hard-drive/SSD.

1.Open the hard-drive/SSD carrier handle.

2.Insert the hard-drive/SSD carrier into the drive bay. Carefully align the channel on the hard-drive/SSD carrier with the appropriate drive slot on the sled.

3.Push the drive carrier into the drive bay.

4.Rotate the carrier handle to the closed position while pushing the carrier into the slot until it locks into place.

5.For the 2.5 inch hard-drive/SSD configuration, turn on the node to which the hard-drive/SSD is assigned, using the iDRAC.

The status LED indicator displays a steady green light if the drive is installed correctly. The drive carrier LED green indicator flashes as the drive rebuilds.

Shutdown procedure for servicing a hard drive/SSD

NOTE: This section is applicable only when you have to turn off the sled to service a hard drive/SSD. In many situations, the hard drive/SSD can be serviced while the sled is powered on.

CAUTION: If you need to turn off the sled to service a hard drive/SSD, wait 30 seconds after the sled’s power indicator turns off before removing the hard drive/SSD. Otherwise, the hard drive/SSD may not be recognized after it is reinstalled and the sled is powered on again.

43

Image 43

Contents Regulatory Model E02B Regulatory Type E02B002 Page Contents Using the Boot Manager navigation keys Boot Manager screen Installing sled componentsTechnical specifications Troubleshooting your systemUsing system diagnostics Jumpers and connectorsGetting help Terms used in the document About your systemTerm Description Front-panel features and indicators Drive-Status Indicator Pattern Condition Hard-drive/SSD indicator patternsBlinking blue Node status indicatorsIndicator Pattern Description Off Solid blueDocumentation matrix Using USB diskette or USB DVD/CD drivesQuick Resource Locator Setting up your system Performing initial system configurationSetting up and configuring the iDRAC IP address Click Get drivers and downloads Logging in to iDRAC Installing the operating systemChoosing the system boot mode Using the System Setup and Boot ManagerUsing the System Setup navigation keys Entering System SetupSystem setup options Responding to error messagesSystem Information screen System Bios screenProcessor Settings screen Memory Settings screenSata Settings screen Integrated Devices screen Boot Settings screenSerial Communications screen System Profile Settings screen Miscellaneous settings System and setup password featuresSystem Security screen Assigning a system and/or setup password Operating with a setup password enabled Using your system password to secure your systemUsing the Boot Manager navigation keys Entering the Uefi Boot ManagerBoot Manager screen Embedded system management IDRAC Settings utilitySystem Setup Main Menu page, click iDRAC Settings Networking configurationsEntering the iDRAC Settings utility Standard configurationIcon Description Network adapter isolation configurationNetwork adapter isolation configuration Isolated networks configurationTrunk configuration or LAG Removing the sled Installing sled componentsRemoving and installing the sled Recommended toolsRemoving and installing a sled Installing the sledInside the sled 2.5 inch hard-drive/SSD system Inside the sledRemoving the cable cover Cable coverRemoving and installing the cable cover Installing the cable coverRemoving the cooling shroud Cooling shroudMaximum Dimm Rank Per Installing the cooling shroudSystem memory Dimm Type DIMMs Populated PerSample memory configurations General memory module installation guidelinesNumber Organization Dimm Slot Population DIMMs Speed Removing memory modulesRemoving the memory module Installing memory modulesHard drive/SSD to node assignment Hard drives/SSDsHard-Drive/SSD Bay Node Removing a hard drive/SSDHard-drive/SSD carrier handle Shutdown procedure for servicing a hard drive/SSD Installing a hard drive/SSDConfiguring the boot drive Hard-drive/SSD backplane Installing a 1.8 inch SSD in the SSD carrierRemoving a 1.8 inch SSD from the SSD carrier Removing the hard-drive/SSD backplane Removing and installing the hard-drive/SSD backplaneInstalling the hard-drive/SSD backplane SSD cage assemblyRemoving the SSD cage assembly Installing the SSD cage assembly Easy restore moduleReplacing the easy restore module Replacing the system battery System batteryRemoving the system board System boardPage Removing and installing the system board Installing the system boardRemoving the control panel Control panelRemoving and installing the control panel Installing the control panelPage Troubleshooting your system Troubleshooting USB devices Troubleshooting hard drivesTroubleshooting the system battery Troubleshooting the system boardSystem messages Diagnostic messagesAlert messages Running the Embedded System Diagnostics Using system diagnosticsDell Embedded System Diagnostics When to use the Embedded System DiagnosticsLeast one event description is recorded System diagnostic controlsConfiguration settings are retained at system boot Jumpers and connectorsSystem board jumper settings Jumper Setting DescriptionConnector Description System board connectorsDisabling a forgotten password Technical specifications Temperature Continuous Operation BatteryEnvironmental Expanded operating temperature TemperatureOperating Altitude De-rating Maximum VibrationMaximum Shock Maximum AltitudeGaseous Contamination Documentation feedback Quick Resource Locator Locating your system Service TagGetting help Contacting Dell