Dell FM120x4 owner manual Removing the hard-drive/SSD backplane

Page 46

Removing the hard-drive/SSD backplane

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1.Turn off the nodes using the operating system commands, or the iDRAC, or the CMC. The sled is powered off when all the nodes are turned off.

2.Remove the sled from the enclosure.

CAUTION: Note the number of each hard drive/SSD and temporarily label them before removal so that you can replace them in the same locations.

CAUTION: To prevent damage to the hard drives/SSDs and the hard-drive/SSD backplane, remove the hard drives/SSDs from the sled before removing the hard-drive/SSD backplane.

3.Remove the hard drive(s)/SSD(s).

4.Disconnect the power cable and SATA cables from the hard-drive/SSD backplane.

5.Pressing the release tab, hold the backplane bracket and lift the backplane away from the sled.

Figure 23. Removing and installing the hard-drive/SSD backplane

 

 

1.

release tab

2.

hard-drive/SSD backplane bracket

3.

hard-drive/SSD backplane

4.

hard-drive/SSD connectors (4)

46

Image 46
Contents Regulatory Model E02B Regulatory Type E02B002 Page Contents Installing sled components Using the Boot Manager navigation keys Boot Manager screenJumpers and connectors Troubleshooting your systemUsing system diagnostics Technical specificationsGetting help Terms used in the document About your systemTerm Description Front-panel features and indicators Hard-drive/SSD indicator patterns Drive-Status Indicator Pattern ConditionSolid blue Node status indicatorsIndicator Pattern Description Off Blinking blueUsing USB diskette or USB DVD/CD drives Documentation matrixQuick Resource Locator Setting up your system Performing initial system configurationSetting up and configuring the iDRAC IP address Logging in to iDRAC Installing the operating system Click Get drivers and downloadsUsing the System Setup and Boot Manager Choosing the system boot modeResponding to error messages Entering System SetupSystem setup options Using the System Setup navigation keysSystem Bios screen System Information screenProcessor Settings screen Memory Settings screenSata Settings screen Integrated Devices screen Boot Settings screenSerial Communications screen System Profile Settings screen Miscellaneous settings System and setup password featuresSystem Security screen Assigning a system and/or setup password Using your system password to secure your system Operating with a setup password enabledUsing the Boot Manager navigation keys Entering the Uefi Boot ManagerBoot Manager screen IDRAC Settings utility Embedded system managementStandard configuration Networking configurationsEntering the iDRAC Settings utility System Setup Main Menu page, click iDRAC SettingsNetwork adapter isolation configuration Icon DescriptionIsolated networks configuration Network adapter isolation configurationTrunk configuration or LAG Recommended tools Installing sled componentsRemoving and installing the sled Removing the sledInstalling the sled Removing and installing a sledInside the sled Inside the sled 2.5 inch hard-drive/SSD systemCable cover Removing the cable coverInstalling the cable cover Removing and installing the cable coverCooling shroud Removing the cooling shroudDimm Type DIMMs Populated Per Installing the cooling shroudSystem memory Maximum Dimm Rank PerGeneral memory module installation guidelines Sample memory configurationsRemoving memory modules Number Organization Dimm Slot Population DIMMs SpeedInstalling memory modules Removing the memory moduleHard drives/SSDs Hard drive/SSD to node assignmentRemoving a hard drive/SSD Hard-Drive/SSD Bay NodeHard-drive/SSD carrier handle Installing a hard drive/SSD Shutdown procedure for servicing a hard drive/SSDConfiguring the boot drive Hard-drive/SSD backplane Installing a 1.8 inch SSD in the SSD carrierRemoving a 1.8 inch SSD from the SSD carrier Removing and installing the hard-drive/SSD backplane Removing the hard-drive/SSD backplaneInstalling the hard-drive/SSD backplane SSD cage assemblyRemoving the SSD cage assembly Installing the SSD cage assembly Easy restore moduleReplacing the easy restore module System battery Replacing the system batterySystem board Removing the system boardPage Installing the system board Removing and installing the system boardControl panel Removing the control panelInstalling the control panel Removing and installing the control panelPage Troubleshooting your system Troubleshooting hard drives Troubleshooting USB devicesTroubleshooting the system board Troubleshooting the system batterySystem messages Diagnostic messagesAlert messages When to use the Embedded System Diagnostics Using system diagnosticsDell Embedded System Diagnostics Running the Embedded System DiagnosticsSystem diagnostic controls Least one event description is recordedJumper Setting Description Jumpers and connectorsSystem board jumper settings Configuration settings are retained at system bootSystem board connectors Connector DescriptionDisabling a forgotten password Technical specifications Temperature BatteryEnvironmental Expanded operating temperature Temperature Continuous OperationMaximum Altitude Maximum VibrationMaximum Shock Operating Altitude De-ratingGaseous Contamination Contacting Dell Quick Resource Locator Locating your system Service TagGetting help Documentation feedback