Dell FM120x4 owner manual SSD cage assembly, Installing the hard-drive/SSD backplane

Page 47

Installing the hard-drive/SSD backplane

1.Align the slots on the hard-drive/SSD backplane with the hooks on the chassis.

2.Lower the backplane into the chassis until it is firmly seated and the release tab clicks into place.

3.Connect the power cable and SATA cables to the backplane.

4.Install the hard drives/SSDs in their original locations.

5.Install the sled in the enclosure.

6.Turn on the sled.

SSD cage assembly

The eight 1.8 inch SSD system supports two SSD backplanes in two SSD cage assemblies. Each SSD cage assembly includes:

•an SSD cage that supports four 1.8 inch SSDs

•one SSD backplane

Removing the SSD cage assembly

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1.Turn off the nodes using the operating system commands, or the iDRAC, or the CMC. The sled is powered off when all the nodes are turned off.

2.Remove the sled from the enclosure.

3.Remove the SSDs.

4.Remove the SATA and power cables from the SSD backplane of the cage assembly.

5.Loosen the spring-loaded screw that secures the SSD cage assembly to the sled chassis.

6.Slide the SSD cage assembly out of the sled.

47

Image 47

Contents Regulatory Model E02B Regulatory Type E02B002 Page Contents Using the Boot Manager navigation keys Boot Manager screen Installing sled componentsTechnical specifications Troubleshooting your systemUsing system diagnostics Jumpers and connectorsGetting help Term Description About your systemTerms used in the document Front-panel features and indicators Drive-Status Indicator Pattern Condition Hard-drive/SSD indicator patternsBlinking blue Node status indicatorsIndicator Pattern Description Off Solid blueDocumentation matrix Using USB diskette or USB DVD/CD drivesQuick Resource Locator Setting up and configuring the iDRAC IP address Performing initial system configurationSetting up your system Click Get drivers and downloads Logging in to iDRAC Installing the operating systemChoosing the system boot mode Using the System Setup and Boot ManagerUsing the System Setup navigation keys Entering System SetupSystem setup options Responding to error messagesSystem Information screen System Bios screenSata Settings screen Memory Settings screenProcessor Settings screen Serial Communications screen Boot Settings screenIntegrated Devices screen System Profile Settings screen System Security screen System and setup password featuresMiscellaneous settings Assigning a system and/or setup password Operating with a setup password enabled Using your system password to secure your systemBoot Manager screen Entering the Uefi Boot ManagerUsing the Boot Manager navigation keys Embedded system management IDRAC Settings utilitySystem Setup Main Menu page, click iDRAC Settings Networking configurationsEntering the iDRAC Settings utility Standard configurationIcon Description Network adapter isolation configurationNetwork adapter isolation configuration Isolated networks configurationTrunk configuration or LAG Removing the sled Installing sled componentsRemoving and installing the sled Recommended toolsRemoving and installing a sled Installing the sledInside the sled 2.5 inch hard-drive/SSD system Inside the sledRemoving the cable cover Cable coverRemoving and installing the cable cover Installing the cable coverRemoving the cooling shroud Cooling shroudMaximum Dimm Rank Per Installing the cooling shroudSystem memory Dimm Type DIMMs Populated PerSample memory configurations General memory module installation guidelinesNumber Organization Dimm Slot Population DIMMs Speed Removing memory modulesRemoving the memory module Installing memory modulesHard drive/SSD to node assignment Hard drives/SSDsHard-Drive/SSD Bay Node Removing a hard drive/SSDHard-drive/SSD carrier handle Shutdown procedure for servicing a hard drive/SSD Installing a hard drive/SSDConfiguring the boot drive Removing a 1.8 inch SSD from the SSD carrier Installing a 1.8 inch SSD in the SSD carrierHard-drive/SSD backplane Removing the hard-drive/SSD backplane Removing and installing the hard-drive/SSD backplaneRemoving the SSD cage assembly SSD cage assemblyInstalling the hard-drive/SSD backplane Replacing the easy restore module Easy restore moduleInstalling the SSD cage assembly Replacing the system battery System batteryRemoving the system board System boardPage Removing and installing the system board Installing the system boardRemoving the control panel Control panelRemoving and installing the control panel Installing the control panelPage Troubleshooting your system Troubleshooting USB devices Troubleshooting hard drivesTroubleshooting the system battery Troubleshooting the system boardAlert messages Diagnostic messagesSystem messages Running the Embedded System Diagnostics Using system diagnosticsDell Embedded System Diagnostics When to use the Embedded System DiagnosticsLeast one event description is recorded System diagnostic controlsConfiguration settings are retained at system boot Jumpers and connectorsSystem board jumper settings Jumper Setting DescriptionConnector Description System board connectorsDisabling a forgotten password Technical specifications Temperature Continuous Operation BatteryEnvironmental Expanded operating temperature TemperatureOperating Altitude De-rating Maximum VibrationMaximum Shock Maximum AltitudeGaseous Contamination Documentation feedback Quick Resource Locator Locating your system Service TagGetting help Contacting Dell