Dell E600I manual Installing the Chassis into an Equipment Cabinet

Page 17

To install the chassis into a prepared rack:

Step Task

1If you are center or rear mounting the chassis in a 19-inch rack, make sure that the mounting brackets are properly positioned.

NOTE: If your are mounting the chassis in a 23-inch rack, install the 23-inch adapters.

2Using a hand cart, pallet jack, or forklift, align the rack-mount holes with the equipment rack holes, situating the chassis on top of the equipment rack shelf bar.

3Insert rack mounting screws in the holes that are not obscured by the front shipping cover. Tighten the screws. See Figure 4-2.

4Loosen and remove the screws attaching the front shipping cover. Remove the cover.

5Insert the remaining rack mounting screws and tighten to secure the chassis in the rack.

Installing the Chassis into an Equipment Cabinet

Install the E600i system after you secure the rack shelf bar. Load the chassis into the lower half of an empty rack to avoid a top-heavy rack. (Figure 4-2). Make sure the cabinet is positioned with adequate space in the front, rear, and sides of the unit for proper ventilation, access to cables, and access for maintenance. See Rack Mounting the Chassis on page 16 for details.

To install the chassis into an equipment cabinet:

Step Task

1Install the equipment rack shelf bar.

2Using a hand cart, pallet jack, or forklift, align the rack-mount holes with the cabinet holes.

3Insert rack mounting screws in the holes that are not obscured by the front shipping cover. Tighten the screws.

4Loosen and remove the screws attaching the front shipping cover. Remove the cover.

5Insert the remaining mounting screws and tighten to secure the chassis in the cabinet.

Installing the Chassis

17

Image 17
Contents E600i TeraScale Installation Guide Page Contents Powering Up System Boot W . d e l l . c o m s u p p o r t . d e l l . c o m Contents 1describes symbols contained in this guide Information Symbols and WarningsInformation Symbols About This GuideRelease Notes for the E-Series Related PublicationsEquipment Rack and Cabinet Requirements Site PreparationSite Selection 2500W AC Power Requirements Power RequirementsDC Power Requirements Storage RequirementsOperating Overview E600i SystemE600i Chassis Rear View E600i Chassis Front View with AC Power SuppliesE600i Hardware Component Operating Requirements Summary E600i System Installation ProcessPage Unpacking the E600i System Installing the ChassisInstalling the Equipment Rack Shelf Bar Standard Front Chassis Rack Mounting To install a equipment rack shelf barTo install the chassis into a prepared rack Installing the Chassis into an Equipment CabinetPage Fan Tray Installing the Fan TrayFan Speed Fan Speed and TemperatureMinimum Power Supply Requirements Power SupplyAC Power Supply Unit AC Power Supply UnitsTo install an AC power supply unit Power Cord RequirementsInstall the AC Power Supply Units To remove an AC power supply unit Remove the AC Power SupplyCable and Connector Requirements DC Power Entry ModulesInstall the DC PEMs To install a DC PEMReplace the DC PEM Removing the DC PEM Safety CoverTo remove a PEM Page Unpacking Installing RPMs, Line Cards, and SFMsLine Cards and RPMs RPMsTo install line cards and RPMs Preparing and Installing the RPMs and Line CardsLine Cards Blank PanelsInstalling RPM into the E600i RPM LEDs Installing a Second RPMRPM Label and LEDs Line Card LEDs Installing Switch Fabric Modules SFMsInstalling SFMs SFM Front Panel and LED Descriptions SFM Front Panel and LEDs2defines the SFM front panel and LED displays Page RPM Ports Connecting the Console and Auxiliary PortsRPM Ports and Cables Auxiliary Port RJ-45 Pin Assignments Cable and Adapter Pin AssignmentsConsole Port RJ-45 Pin Assignments Pin Assignments Between E600i Console and DB-25 Adapter Accessing the Console with a DB-9 AdapterAccessing the Console with a DB-25 Adapter Accessing the Auxiliary Port by Modem Accessing the 10/100 Ethernet Management PortRJ-45 to DB-25 Adapter Pin Modem Assignments 100 Ethernet Management Port LEDsSupplying Power Powering UpTo supply power to the E600i system PreparationBooting from the Bootuser Prompt Booting to the CLI PromptRemoving and Replacing the Fan Tray Removing and Replacing PartsReplacing 2500W AC Power Supply Removing and Replacing Power ModulesReplacing DC PEMs Removing the Power CordDC PEM Label Removing and Replacing RPMs, Line Cards, or SFMsNo linecard number To remove and install an SFMReplacing the E600i Air Filter Removing and Replacing the Air FilterTo remove and replace the air filter Page External Flash Memory Card Overview Using a Flash Memory CardInserting the External Flash Memory Card Removing the External Flash Memory CardDisplaying Files Stored on the External Flash Formatting an External Flash CardCopying Files to the External Flash Dir Command Example Page Booting from the Bootuser Prompt System BootE600i System Boot Process Help To configure the chassis from the Bootuser promptUse the boot change command to edit appropriate fields Show default-gateway default-gateway ip-address Force10 Page Table B-1. Alarm Events and Reporting AlarmsSFMs and Alarms AC Power Supplies and AlarmsAlarms Alarms W . d e l l . c o m s u p p o r t . d e l l . c o m This appendix contains the following major sections System SpecificationsChassis Physical Design Environmental AC Power Supply Unit RequirementsDC Power Entry Module Requirement Agency Compliance SFM and RPM Power RequirementsJapan Vcci Compliance for Class a Equipment Product Recycling and Disposal Safety Standards and Compliance Agency CertificationsElectromagnetic Compatibility EMC Figure C-1. The European Weee symbol Technical Support Accessing iSupport ServicesISupport Website This appendix contains these major sectionsRequest tab Contacting the Technical Assistance CenterTo request replacement hardware, follow these steps Requesting a Hardware ReplacementPage Page W. d e l l . c o m s u p p o r t . d e l l . c o m

E600I specifications

The Dell E600i stands as a robust and versatile solution in the realm of high-performance computing, designed to meet the demands of both enterprise environments and individual users. This workstation is characterized by its powerful processing capabilities, advanced graphics options, and extensive customization features that allow users to tailor the system to fit specific needs.

At the heart of the Dell E600i is its support for the latest multi-core processors, offering substantial performance for demanding applications, whether in data analysis, 3D modeling, or intensive computational tasks. Users can choose from a range of Intel Xeon or Core processors, ensuring that they can achieve optimal performance levels according to their workload requirements.

In terms of graphics, the E600i provides the option to integrate high-performance GPU selections from NVIDIA or AMD. This makes it particularly suitable for graphic design, video editing, and complex simulations. The inclusion of dedicated graphics cards not only enhances rendering capabilities but also supports advanced visualization technologies, which are essential for industries such as architecture, engineering, and media production.

One of the standout characteristics of the E600i is its expandability. With multiple expansion slots available, users can easily upgrade or integrate additional components to enhance performance or to adapt to new tasks. This system supports ample memory configurations, allowing for significant multitasking and overall system responsiveness.

In addition to its hardware capabilities, the Dell E600i leverages cutting-edge technologies to enhance usability and performance. Features such as Dell Precision Optimizer streamline workflow by automatically adjusting settings to optimize the performance of specific applications. Furthermore, Dell’s reliability in terms of build quality and support ensures that users can rely on their workstation for long durations without concern.

The E600i is also engineered with an eco-friendly focus, incorporating energy-efficient technologies that not only reduce operating costs but also minimize environmental impact. This attention to sustainability makes it an attractive option for businesses and professionals committed to responsible practices.

In conclusion, the Dell E600i is a high-performance workstation that brings together powerful processing, advanced graphics capabilities, and exceptional expandability. Its robust features and focus on usability make it a compelling choice for professionals in numerous fields, ensuring that they can tackle any project with confidence and ease.