Dell E600I manual Dir Command Example

Page 53

Figure 11-1. dir Command Example

Force10#dir slot0:

Directory of slot0:

1 -rwx

6478482

Sep 7 101 16:54:34 E1200.BIN

FTOS supports up to a 40-character file name length, up to a 180-character local file path length, and up to a 256-character remote file path length.

Refer to the FTOS Command Line Interface Reference for CLI commands.

Using a Flash Memory Card

53

Image 53

Contents E600i TeraScale Installation Guide Page Contents Powering Up System Boot W . d e l l . c o m s u p p o r t . d e l l . c o m Contents 1describes symbols contained in this guide Information Symbols and WarningsInformation Symbols About This GuideRelease Notes for the E-Series Related PublicationsEquipment Rack and Cabinet Requirements Site PreparationSite Selection 2500W AC Power Requirements Power RequirementsDC Power Requirements Storage RequirementsOperating Overview E600i SystemE600i Chassis Rear View E600i Chassis Front View with AC Power SuppliesE600i Hardware Component Operating Requirements Summary E600i System Installation ProcessPage Unpacking the E600i System Installing the ChassisInstalling the Equipment Rack Shelf Bar Standard Front Chassis Rack Mounting To install a equipment rack shelf barTo install the chassis into a prepared rack Installing the Chassis into an Equipment CabinetPage Fan Tray Installing the Fan TrayFan Speed Fan Speed and TemperatureMinimum Power Supply Requirements Power SupplyAC Power Supply Unit AC Power Supply UnitsTo install an AC power supply unit Power Cord RequirementsInstall the AC Power Supply Units To remove an AC power supply unit Remove the AC Power SupplyCable and Connector Requirements DC Power Entry ModulesInstall the DC PEMs To install a DC PEMReplace the DC PEM Removing the DC PEM Safety CoverTo remove a PEM Page Unpacking Installing RPMs, Line Cards, and SFMsLine Cards and RPMs RPMsTo install line cards and RPMs Preparing and Installing the RPMs and Line CardsLine Cards Blank PanelsInstalling RPM into the E600i RPM LEDs Installing a Second RPMRPM Label and LEDs Line Card LEDs Installing Switch Fabric Modules SFMsInstalling SFMs SFM Front Panel and LED Descriptions SFM Front Panel and LEDs2defines the SFM front panel and LED displays Page RPM Ports Connecting the Console and Auxiliary PortsRPM Ports and Cables Auxiliary Port RJ-45 Pin Assignments Cable and Adapter Pin AssignmentsConsole Port RJ-45 Pin Assignments Pin Assignments Between E600i Console and DB-25 Adapter Accessing the Console with a DB-9 AdapterAccessing the Console with a DB-25 Adapter Accessing the Auxiliary Port by Modem Accessing the 10/100 Ethernet Management PortRJ-45 to DB-25 Adapter Pin Modem Assignments 100 Ethernet Management Port LEDsSupplying Power Powering UpTo supply power to the E600i system PreparationBooting from the Bootuser Prompt Booting to the CLI PromptRemoving and Replacing the Fan Tray Removing and Replacing PartsReplacing 2500W AC Power Supply Removing and Replacing Power ModulesReplacing DC PEMs Removing the Power CordDC PEM Label Removing and Replacing RPMs, Line Cards, or SFMsNo linecard number To remove and install an SFMReplacing the E600i Air Filter Removing and Replacing the Air FilterTo remove and replace the air filter Page External Flash Memory Card Overview Using a Flash Memory CardInserting the External Flash Memory Card Removing the External Flash Memory CardDisplaying Files Stored on the External Flash Formatting an External Flash CardCopying Files to the External Flash Dir Command Example Page Booting from the Bootuser Prompt System BootE600i System Boot Process Help To configure the chassis from the Bootuser promptUse the boot change command to edit appropriate fields Show default-gateway default-gateway ip-address Force10 Page Table B-1. Alarm Events and Reporting AlarmsSFMs and Alarms AC Power Supplies and AlarmsAlarms Alarms W . d e l l . c o m s u p p o r t . d e l l . c o m This appendix contains the following major sections System SpecificationsChassis Physical Design Environmental AC Power Supply Unit RequirementsDC Power Entry Module Requirement Agency Compliance SFM and RPM Power RequirementsJapan Vcci Compliance for Class a Equipment Product Recycling and Disposal Safety Standards and Compliance Agency CertificationsElectromagnetic Compatibility EMC Figure C-1. The European Weee symbol Technical Support Accessing iSupport ServicesISupport Website This appendix contains these major sectionsRequest tab Contacting the Technical Assistance CenterTo request replacement hardware, follow these steps Requesting a Hardware ReplacementPage Page W. d e l l . c o m s u p p o r t . d e l l . c o m