Dell E600I manual Line Card LEDs, Installing Switch Fabric Modules SFMs

Page 33

Table 7-1. RPM LEDs

Flash

In Use

Green: flash memory card is in the process of a read or write process. Do not remove the

 

 

flash card when the In Use LED is lit.

 

 

Unlit: not in use.

 

 

 

 

Primary

Green: primary

 

 

Unlit: secondary (or standby)

 

Status

This is a bi-color LED.

 

 

Green: operational

 

 

Amber: fault detected

 

 

Flashing green: booting

 

 

Unlit: in secondary mode or power is off

 

 

 

Line Card LEDs

Line card LEDs are described in the documentation specific to each line card. Refer to the installation documentation that came with the card for to understand LED appearance and meaning.

Installing Switch Fabric Modules (SFMs)

A minimum of four SFMs are required in order for the E600i system to operate properly. There is an additional slot available for a redundant SFM. SFMs carry traffic between line cards or between RPMs and a line card. SFMs plug directly into the backplane, which provides high-speed access to the line cards. The switch fabric receives user data packets and redirects them to the appropriate destinations according to the routing information.

CAUTION: If you are not operating your E600i system with redundancy, your SFM package will include a blank panel. Blanks do not have board components or connector pins.

You must install SFMs starting on the left (slots 3 or 0) moving to the right (slots 2 or 4).

Step Task

1Remove an SFM from the anti-static packaging.

2Align the SFM with the guide and gently slide it into the slot until you feel the connectors engage with the chassis backplane.

NOTE: Hold the SFM by the edges. Avoid touching the printed circuit board and connector pins. Extend the top and bottom card levers before you insert the card into the slot.

3Rotate the lever to seat the backplane connectors and card in place.

4Secure each SFM in place by tightening the captive screw.

5Continue the process for the remaining SFMs.

6Align any blank panels with the guides and gently slide toward the backplane. Secure each blank panel by tightening the single captive screw.

Installing RPMs, Line Cards, and SFMs 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents E600i TeraScale Installation Guide Page Contents Powering Up System Boot W . d e l l . c o m s u p p o r t . d e l l . c o m Contents 1describes symbols contained in this guide Information Symbols and WarningsInformation Symbols About This GuideRelease Notes for the E-Series Related PublicationsSite Preparation Site SelectionEquipment Rack and Cabinet Requirements 2500W AC Power Requirements Power RequirementsDC Power Requirements Storage RequirementsOperating Overview E600i SystemE600i Chassis Rear View E600i Chassis Front View with AC Power SuppliesE600i Hardware Component Operating Requirements Summary E600i System Installation ProcessPage Installing the Chassis Installing the Equipment Rack Shelf BarUnpacking the E600i System Standard Front Chassis Rack Mounting To install a equipment rack shelf barTo install the chassis into a prepared rack Installing the Chassis into an Equipment CabinetPage Fan Tray Installing the Fan TrayFan Speed Fan Speed and TemperatureMinimum Power Supply Requirements Power SupplyAC Power Supply Unit AC Power Supply UnitsPower Cord Requirements Install the AC Power Supply UnitsTo install an AC power supply unit To remove an AC power supply unit Remove the AC Power SupplyCable and Connector Requirements DC Power Entry ModulesInstall the DC PEMs To install a DC PEMReplace the DC PEM Removing the DC PEM Safety CoverTo remove a PEM Page Unpacking Installing RPMs, Line Cards, and SFMsLine Cards and RPMs RPMsTo install line cards and RPMs Preparing and Installing the RPMs and Line CardsLine Cards Blank PanelsInstalling RPM into the E600i Installing a Second RPM RPM Label and LEDsRPM LEDs Line Card LEDs Installing Switch Fabric Modules SFMsInstalling SFMs SFM Front Panel and LEDs 2defines the SFM front panel and LED displaysSFM Front Panel and LED Descriptions Page Connecting the Console and Auxiliary Ports RPM Ports and CablesRPM Ports Cable and Adapter Pin Assignments Console Port RJ-45 Pin AssignmentsAuxiliary Port RJ-45 Pin Assignments Accessing the Console with a DB-9 Adapter Accessing the Console with a DB-25 AdapterPin Assignments Between E600i Console and DB-25 Adapter Accessing the Auxiliary Port by Modem Accessing the 10/100 Ethernet Management PortRJ-45 to DB-25 Adapter Pin Modem Assignments 100 Ethernet Management Port LEDsSupplying Power Powering UpTo supply power to the E600i system PreparationBooting from the Bootuser Prompt Booting to the CLI PromptRemoving and Replacing the Fan Tray Removing and Replacing PartsReplacing 2500W AC Power Supply Removing and Replacing Power ModulesReplacing DC PEMs Removing the Power CordDC PEM Label Removing and Replacing RPMs, Line Cards, or SFMsNo linecard number To remove and install an SFMReplacing the E600i Air Filter Removing and Replacing the Air FilterTo remove and replace the air filter Page External Flash Memory Card Overview Using a Flash Memory CardInserting the External Flash Memory Card Removing the External Flash Memory CardFormatting an External Flash Card Copying Files to the External FlashDisplaying Files Stored on the External Flash Dir Command Example Page System Boot E600i System Boot ProcessBooting from the Bootuser Prompt Help To configure the chassis from the Bootuser promptUse the boot change command to edit appropriate fields Show default-gateway default-gateway ip-address Force10 Page Table B-1. Alarm Events and Reporting AlarmsSFMs and Alarms AC Power Supplies and AlarmsAlarms Alarms W . d e l l . c o m s u p p o r t . d e l l . c o m System Specifications Chassis Physical DesignThis appendix contains the following major sections AC Power Supply Unit Requirements DC Power Entry Module RequirementEnvironmental Agency Compliance SFM and RPM Power RequirementsJapan Vcci Compliance for Class a Equipment Safety Standards and Compliance Agency Certifications Electromagnetic Compatibility EMCProduct Recycling and Disposal Figure C-1. The European Weee symbol Technical Support Accessing iSupport ServicesISupport Website This appendix contains these major sectionsRequest tab Contacting the Technical Assistance CenterTo request replacement hardware, follow these steps Requesting a Hardware ReplacementPage Page W. d e l l . c o m s u p p o r t . d e l l . c o m

E600I specifications

The Dell E600i stands as a robust and versatile solution in the realm of high-performance computing, designed to meet the demands of both enterprise environments and individual users. This workstation is characterized by its powerful processing capabilities, advanced graphics options, and extensive customization features that allow users to tailor the system to fit specific needs.

At the heart of the Dell E600i is its support for the latest multi-core processors, offering substantial performance for demanding applications, whether in data analysis, 3D modeling, or intensive computational tasks. Users can choose from a range of Intel Xeon or Core processors, ensuring that they can achieve optimal performance levels according to their workload requirements.

In terms of graphics, the E600i provides the option to integrate high-performance GPU selections from NVIDIA or AMD. This makes it particularly suitable for graphic design, video editing, and complex simulations. The inclusion of dedicated graphics cards not only enhances rendering capabilities but also supports advanced visualization technologies, which are essential for industries such as architecture, engineering, and media production.

One of the standout characteristics of the E600i is its expandability. With multiple expansion slots available, users can easily upgrade or integrate additional components to enhance performance or to adapt to new tasks. This system supports ample memory configurations, allowing for significant multitasking and overall system responsiveness.

In addition to its hardware capabilities, the Dell E600i leverages cutting-edge technologies to enhance usability and performance. Features such as Dell Precision Optimizer streamline workflow by automatically adjusting settings to optimize the performance of specific applications. Furthermore, Dell’s reliability in terms of build quality and support ensures that users can rely on their workstation for long durations without concern.

The E600i is also engineered with an eco-friendly focus, incorporating energy-efficient technologies that not only reduce operating costs but also minimize environmental impact. This attention to sustainability makes it an attractive option for businesses and professionals committed to responsible practices.

In conclusion, the Dell E600i is a high-performance workstation that brings together powerful processing, advanced graphics capabilities, and exceptional expandability. Its robust features and focus on usability make it a compelling choice for professionals in numerous fields, ensuring that they can tackle any project with confidence and ease.
Top Page Image Contents