Dell E600I manual Power Cord Requirements, Install the AC Power Supply Units

Page 23

Power Cord Requirements

If using a power cord other then a Dell Force10 supplied power cord, the cord must terminate at a right angle (IEC320 C19 connector) to the power module, see Figure 6-3. The power source end of the power cord must have an appropriately sized plug that complies with your local electrical codes. Conductor size must also conform to your local electrical codes.

The following are Dell Force10 supplied plug types.

•EU: CEE 7/7

•UK:CEE7/7, BS 1363

•SWZ: CEE7/7, 309

•JAP: NEMA 5-20

•JAP 220: NEMA 6-20, L6-20

•US: C14, C20, NEMA 5-20, L5-20

•US 220: NEMA 6-20, L6-20, L6-30 (30A)

Install the AC Power Supply Units

To install an AC power supply unit:

Step Task

1Verify that the power switch on the power supply is in the OFF position.

2Orient the power supply handle to the left, and slide the backplane connector end into a power supply slot.

3Secure the power supply into place by tightening the two locking screws to 5 in-lbs.

4Plug an AC power cord into the socket on the front of the unit:

a Loosen the power cord retainer thumb screw.

b Rotate the retainer clockwise away from the socket and plug the power cord into the socket.

cRotate the retainer counter clockwise over the power cord, and tighten the thumb screw to secure the power cord.

Figure 6-3. Securing the AC Power Cord

Power Supply

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents E600i TeraScale Installation Guide Page Contents Powering Up System Boot W . d e l l . c o m s u p p o r t . d e l l . c o m Contents About This Guide Information Symbols and Warnings1describes symbols contained in this guide Information SymbolsRelease Notes for the E-Series Related PublicationsEquipment Rack and Cabinet Requirements Site PreparationSite Selection Storage Requirements Power Requirements2500W AC Power Requirements DC Power RequirementsOperating Overview E600i SystemE600i Chassis Rear View E600i Chassis Front View with AC Power SuppliesE600i Hardware Component Operating Requirements Summary E600i System Installation ProcessPage Unpacking the E600i System Installing the ChassisInstalling the Equipment Rack Shelf Bar Standard Front Chassis Rack Mounting To install a equipment rack shelf barTo install the chassis into a prepared rack Installing the Chassis into an Equipment CabinetPage Fan Tray Installing the Fan TrayFan Speed Fan Speed and TemperatureMinimum Power Supply Requirements Power SupplyAC Power Supply Unit AC Power Supply UnitsTo install an AC power supply unit Power Cord RequirementsInstall the AC Power Supply Units To remove an AC power supply unit Remove the AC Power SupplyTo install a DC PEM DC Power Entry ModulesCable and Connector Requirements Install the DC PEMsReplace the DC PEM Removing the DC PEM Safety CoverTo remove a PEM Page RPMs Installing RPMs, Line Cards, and SFMsUnpacking Line Cards and RPMsBlank Panels Preparing and Installing the RPMs and Line CardsTo install line cards and RPMs Line CardsInstalling RPM into the E600i RPM LEDs Installing a Second RPMRPM Label and LEDs Line Card LEDs Installing Switch Fabric Modules SFMsInstalling SFMs SFM Front Panel and LED Descriptions SFM Front Panel and LEDs2defines the SFM front panel and LED displays Page RPM Ports Connecting the Console and Auxiliary PortsRPM Ports and Cables Auxiliary Port RJ-45 Pin Assignments Cable and Adapter Pin AssignmentsConsole Port RJ-45 Pin Assignments Pin Assignments Between E600i Console and DB-25 Adapter Accessing the Console with a DB-9 AdapterAccessing the Console with a DB-25 Adapter 100 Ethernet Management Port LEDs Accessing the 10/100 Ethernet Management PortAccessing the Auxiliary Port by Modem RJ-45 to DB-25 Adapter Pin Modem AssignmentsPreparation Powering UpSupplying Power To supply power to the E600i systemBooting from the Bootuser Prompt Booting to the CLI PromptRemoving and Replacing the Fan Tray Removing and Replacing PartsReplacing 2500W AC Power Supply Removing and Replacing Power ModulesReplacing DC PEMs Removing the Power CordDC PEM Label Removing and Replacing RPMs, Line Cards, or SFMsNo linecard number To remove and install an SFMReplacing the E600i Air Filter Removing and Replacing the Air FilterTo remove and replace the air filter Page Removing the External Flash Memory Card Using a Flash Memory CardExternal Flash Memory Card Overview Inserting the External Flash Memory CardDisplaying Files Stored on the External Flash Formatting an External Flash CardCopying Files to the External Flash Dir Command Example Page Booting from the Bootuser Prompt System BootE600i System Boot Process Help To configure the chassis from the Bootuser promptUse the boot change command to edit appropriate fields Show default-gateway default-gateway ip-address Force10 Page Table B-1. Alarm Events and Reporting AlarmsSFMs and Alarms AC Power Supplies and AlarmsAlarms Alarms W . d e l l . c o m s u p p o r t . d e l l . c o m This appendix contains the following major sections System SpecificationsChassis Physical Design Environmental AC Power Supply Unit RequirementsDC Power Entry Module Requirement Agency Compliance SFM and RPM Power RequirementsJapan Vcci Compliance for Class a Equipment Product Recycling and Disposal Safety Standards and Compliance Agency CertificationsElectromagnetic Compatibility EMC Figure C-1. The European Weee symbol This appendix contains these major sections Accessing iSupport ServicesTechnical Support ISupport WebsiteRequest tab Contacting the Technical Assistance CenterTo request replacement hardware, follow these steps Requesting a Hardware ReplacementPage Page W. d e l l . c o m s u p p o r t . d e l l . c o m

E600I specifications

The Dell E600i stands as a robust and versatile solution in the realm of high-performance computing, designed to meet the demands of both enterprise environments and individual users. This workstation is characterized by its powerful processing capabilities, advanced graphics options, and extensive customization features that allow users to tailor the system to fit specific needs.

At the heart of the Dell E600i is its support for the latest multi-core processors, offering substantial performance for demanding applications, whether in data analysis, 3D modeling, or intensive computational tasks. Users can choose from a range of Intel Xeon or Core processors, ensuring that they can achieve optimal performance levels according to their workload requirements.

In terms of graphics, the E600i provides the option to integrate high-performance GPU selections from NVIDIA or AMD. This makes it particularly suitable for graphic design, video editing, and complex simulations. The inclusion of dedicated graphics cards not only enhances rendering capabilities but also supports advanced visualization technologies, which are essential for industries such as architecture, engineering, and media production.

One of the standout characteristics of the E600i is its expandability. With multiple expansion slots available, users can easily upgrade or integrate additional components to enhance performance or to adapt to new tasks. This system supports ample memory configurations, allowing for significant multitasking and overall system responsiveness.

In addition to its hardware capabilities, the Dell E600i leverages cutting-edge technologies to enhance usability and performance. Features such as Dell Precision Optimizer streamline workflow by automatically adjusting settings to optimize the performance of specific applications. Furthermore, Dell’s reliability in terms of build quality and support ensures that users can rely on their workstation for long durations without concern.

The E600i is also engineered with an eco-friendly focus, incorporating energy-efficient technologies that not only reduce operating costs but also minimize environmental impact. This attention to sustainability makes it an attractive option for businesses and professionals committed to responsible practices.

In conclusion, the Dell E600i is a high-performance workstation that brings together powerful processing, advanced graphics capabilities, and exceptional expandability. Its robust features and focus on usability make it a compelling choice for professionals in numerous fields, ensuring that they can tackle any project with confidence and ease.
Top Page Image Contents