Dell E600I manual To configure the chassis from the Bootuser prompt, Help

Page 56

To configure the chassis from the BOOT_USER prompt:

1	help	• The BOOT_USER # prompt appears after an autoboot interruption. This is the
	or	default boot prompt, not the CLI prompt.
	?	• Enter help or ? to display a list of available commands and syntax.
		• Enter syntax help to display syntax information and variable descriptions.
		• Some display output you are given the option to continue the help screen display
		<cr> or to stop q<cr>.
		• You can abbreviate the boot commands by entering only the first letter of a
		command word. A matching algorithm displays the commands starting with the
		letter or letters you entered. For example, b displays the commands starting with
		the letter b, boot change and boot selector. Entering s h displays the syntax
		help information.
		• All commands are case insensitive.
2	Execute the following show commands to display important boot information:
	show boot selector

The show boot selector command displays the boot ROM image currently selected and the most recently booted ROM image.

BOOT_USER # show boot selector

ROM BOOTSTRAP SELECTOR PARMETERS:

================================

3show bootflash

This command displays information about the current boot ROM.

BOOT_USER # show bootflash

GENERAL BOOTFLASH INFO

======================

Bootflash Partition A:

Force10 Networks System Boot

Copyright 1999-2001 Force10 Networks, Inc.

ROM Header Version 1.0

Official CP_IMG_BOOT, BSP Release 2.0.0.14

Created Fri Sep 2 18:22:47 US/Pacific 2004

Bootflash Partition B:

System Boot

56

Image 56

Contents E600i TeraScale Installation Guide Page Contents Powering Up System Boot W . d e l l . c o m s u p p o r t . d e l l . c o m Contents Information Symbols and Warnings 1describes symbols contained in this guideInformation Symbols About This GuideRelated Publications Release Notes for the E-SeriesEquipment Rack and Cabinet Requirements Site PreparationSite Selection Power Requirements 2500W AC Power RequirementsDC Power Requirements Storage RequirementsE600i System Operating OverviewE600i Chassis Front View with AC Power Supplies E600i Chassis Rear ViewE600i System Installation Process E600i Hardware Component Operating Requirements SummaryPage Unpacking the E600i System Installing the ChassisInstalling the Equipment Rack Shelf Bar To install a equipment rack shelf bar Standard Front Chassis Rack MountingInstalling the Chassis into an Equipment Cabinet To install the chassis into a prepared rackPage Installing the Fan Tray Fan TrayFan Speed and Temperature Fan SpeedPower Supply Minimum Power Supply RequirementsAC Power Supply Units AC Power Supply UnitTo install an AC power supply unit Power Cord RequirementsInstall the AC Power Supply Units Remove the AC Power Supply To remove an AC power supply unitDC Power Entry Modules Cable and Connector RequirementsInstall the DC PEMs To install a DC PEMRemoving the DC PEM Safety Cover Replace the DC PEMTo remove a PEM Page Installing RPMs, Line Cards, and SFMs UnpackingLine Cards and RPMs RPMsPreparing and Installing the RPMs and Line Cards To install line cards and RPMsLine Cards Blank PanelsInstalling RPM into the E600i RPM LEDs Installing a Second RPMRPM Label and LEDs Installing Switch Fabric Modules SFMs Line Card LEDsInstalling SFMs SFM Front Panel and LED Descriptions SFM Front Panel and LEDs2defines the SFM front panel and LED displays Page RPM Ports Connecting the Console and Auxiliary PortsRPM Ports and Cables Auxiliary Port RJ-45 Pin Assignments Cable and Adapter Pin AssignmentsConsole Port RJ-45 Pin Assignments Pin Assignments Between E600i Console and DB-25 Adapter Accessing the Console with a DB-9 AdapterAccessing the Console with a DB-25 Adapter Accessing the 10/100 Ethernet Management Port Accessing the Auxiliary Port by ModemRJ-45 to DB-25 Adapter Pin Modem Assignments 100 Ethernet Management Port LEDsPowering Up Supplying PowerTo supply power to the E600i system PreparationBooting to the CLI Prompt Booting from the Bootuser PromptRemoving and Replacing Parts Removing and Replacing the Fan TrayRemoving and Replacing Power Modules Replacing 2500W AC Power SupplyRemoving the Power Cord Replacing DC PEMsRemoving and Replacing RPMs, Line Cards, or SFMs DC PEM LabelTo remove and install an SFM No linecard numberRemoving and Replacing the Air Filter Replacing the E600i Air FilterTo remove and replace the air filter Page Using a Flash Memory Card External Flash Memory Card OverviewInserting the External Flash Memory Card Removing the External Flash Memory CardDisplaying Files Stored on the External Flash Formatting an External Flash CardCopying Files to the External Flash Dir Command Example Page Booting from the Bootuser Prompt System BootE600i System Boot Process To configure the chassis from the Bootuser prompt HelpUse the boot change command to edit appropriate fields Show default-gateway default-gateway ip-address Force10 Page Alarms Table B-1. Alarm Events and ReportingAC Power Supplies and Alarms SFMs and AlarmsAlarms Alarms W . d e l l . c o m s u p p o r t . d e l l . c o m This appendix contains the following major sections System SpecificationsChassis Physical Design Environmental AC Power Supply Unit RequirementsDC Power Entry Module Requirement SFM and RPM Power Requirements Agency ComplianceJapan Vcci Compliance for Class a Equipment Product Recycling and Disposal Safety Standards and Compliance Agency CertificationsElectromagnetic Compatibility EMC Figure C-1. The European Weee symbol Accessing iSupport Services Technical SupportISupport Website This appendix contains these major sectionsContacting the Technical Assistance Center Request tabRequesting a Hardware Replacement To request replacement hardware, follow these stepsPage Page W. d e l l . c o m s u p p o r t . d e l l . c o m