Dell 3000i manual Configure Chap Authentication on the Storage Array optional

Page 47

Step 5: Configure CHAP Authentication on the Storage Array (optional)

If you are configuring CHAP authentication of any kind (either target-only or target and mutual), you must complete this step and Step 6: Configure CHAP Authentication on the Host Server (optional).

If you are not configuring any type of CHAP, skip these steps and go to Step 7: Connect to the Target Storage Array from the Host Server.

NOTE: If you choose to configure mutual CHAP authentication, you must first configure target CHAP.

Remember, in terms of iSCSI configuration, the term target always refers to the storage array.

Configuring Target CHAP Authentication on the Storage Array

1From MD Storage Manager, click the iSCSI tab, then Change Target Authentication. Make a selection based on the following:

Table 4-7. CHAP Settings

Selection

Description

 

 

None

This is the default selection. If None is the only selection, the storage array will

 

allow an iSCSI initiator to log on without supplying any type of CHAP

 

authentication.

None and

The storage array will allow an iSCSI initiator to log on with or without CHAP

CHAP

authentication.

CHAP

If CHAP is selected and None is deselected, the storage array will require CHAP

 

authentication before allowing access.

 

 

2To configure a CHAP secret, select CHAP and select CHAP Secret.

3Enter the Target CHAP secret (or Generate Random Secret), confirm it in Confirm Target CHAP Secret and click OK.

Although the storage array allows sizes from 12 to 57 characters, many initiators only support CHAP secret sizes up to 16 characters (128-bit).

NOTE: Once entered, a CHAP secret is not retrievable. Make sure you record the secret in an accessible place. If Generate Random Secret is used, copy and past the secret into a text file for future reference since the same CHAP secret will be used to authenticate any new host servers you may add to the storage array. If you forget this CHAP secret, you must disconnect all existing hosts attached to the storage array and repeat the steps in this chapter to re-add them.

4Click OK.

Setting Up Your iSCSI Storage Array

47

Image 47
Contents Systems Installation Guide February Contents If you are using Rhel 5 or Sles 10 SP1 Configuring iSCSI on your Storage ArrayIf you are using Windows Server 2008 Core Version Guidelines for Configuring Your Network for iSCSI Contents Introduction IntroductionSystem Requirements Management Station Hardware RequirementsIntroduction to Storage Arrays About the Enclosure Connections Hardware InstallationStorage Configuration Planning Redundancy vs. Nonredundancy Direct-Attached SolutionsCabling the Enclosure MD3000i RAID Private network Controller Hardware InstallationTwo-node cluster Ethernet Two host server Corporate, public or private network Four host server PortControllers Enclosure dual Private network Controllers Network-Attached SolutionsIP SAN Gigabit Ethernet Host servers Ethernet switch Attaching MD1000 Expansion Enclosures Expanding with Previously Configured MD1000 Enclosures Expanding with New MD1000 Enclosures Hardware Installation Software Installation Software InstallationSystem Assembly and Startup To install the iSCSI initiator after Rhel 4 installation Installing the iSCSI Initiator on a Windows Host ServerInstalling the iSCSI Initiator on a Linux Host Server To install the iSCSI initiator during Rhel 4 installationTo install the iSCSI initiator after Rhel 5 installation To install the iSCSI initiator during Rhel 5 installationTo install the iSCSI initiator after Sles 9 installation To install the iSCSI initiator during Sles 9 installationInstalling MD Storage Software Software Installation Command to manually mount CD is When the installation completes, click Done Installing a Dedicated Management Station Windows and Linux Documentation for Windows Systems Viewing Resource CD ContentsInstalling the Manuals Insert the CD Documentation for Linux SystemsInstalling the Manuals Terminology Array Setup and iSCSI ConfigurationBefore You Start Target ISCSI Configuration WorksheetManagement station Storage arrayISCSI controller 1, SubnetDefault gateway Setting Up Your iSCSI Storage ArrayStatic IP address storage array ISCSI controller 0,Target Chap MD3000iArray Using iSNSConfiguring iSCSI on Your Storage Array Manual Storage Array Discovery Default Management Port SettingsDiscover the Storage Array Out-of-band management only Automatic Storage Array DiscoverySet Up the Array Ethernet Management Ports, then Initial Setup Tasks→ ConfigureUpdate your management station Addresses on each controllerConfigure the iSCSI Ports on the Storage Array Perform Target Discovery from the iSCSI Initiator If you are using Windows Server 2008 Core VersionStart the iSCSI service sc start msiscsi If you are using Linux Server Etc/init.d/iscsi restart If you are using Rhel 5 or Sles 10 SP1Iscsiadm -m node -T initiatorusername -p targetip -u Configure Host Access Mutual Chap Understanding Chap AuthenticationWhat is CHAP? Target ChapChap Types Defined Description How Chap Is Set UpChap Definitions Chap Settings Selection Description None Configure Chap Authentication on the Storage Array optionalConfiguring Target Chap Authentication on the Storage Array Configuring Mutual Chap Authentication on the Storage Array Configure Chap Authentication on the Host Server optional IPaddressofiSCSIportonstoragearray CHAPusername CHAPpassword Setting Up Your iSCSI Storage Array If you are using Rhel 5 or Sles 10 SP1 If you are using SLES10 SP1 via the GUI Connect to the Target Storage Array from the Host Server TCPPortNumberOfTargetPortal is Iscsicli SessionList If you are using a Linux ServerViewing the status of your iSCSI connections Optional Set Up In-Band Management Troubleshooting Tools Premium FeaturesSetting Up Your iSCSI Storage Array Uninstalling Software Uninstalling SoftwareUninstalling From Windows Uninstalldellmdstoragemanager and press Enter Uninstalling From LinuxNetwork Configuration Guidelines Guidelines for Configuring Your Network for iSCSIWindows Host Setup Linux Host Setup NETWORKING=yes HOSTNAME=mymachine.mycompany.com Configuring TCP/IP on Linux using Dhcp root users onlyNetwork Configuration Guidelines Index IndexLinux, 64 static IP, 63 Wins RAID

3000i specifications

The Dell 3000i is a powerful and versatile storage solution designed to meet the needs of modern businesses. Known for its flexibility and efficiency, this entry-level storage array offers a range of features that cater to small to medium enterprises and branch offices, providing them with reliable, scalable, and high-performance data management capabilities.

One of the standout features of the Dell 3000i is its impressive performance. It is powered by Dell's proprietary technology, enabling it to handle various workloads with ease. With support for both block and file storage, the 3000i allows organizations to streamline their data operations and optimize their storage strategies. This flexibility means that regardless of the specific requirements, users can manage their data efficiently and effectively.

The Dell 3000i supports multiple connectivity options, including iSCSI and Fibre Channel, ensuring that it can be integrated seamlessly into existing IT environments. This versatility allows organizations to leverage their current infrastructure while capitalizing on the advanced capabilities of the 3000i. Additionally, it features a modular architecture, enabling users to scale their storage incrementally as their needs grow. This means businesses can start with a small footprint and expand their storage capacity without any disruption.

Data protection is a critical concern for all organizations, and the Dell 3000i addresses this with advanced RAID configurations, which safeguard data against hardware failures. Furthermore, it includes features such as snapshots and remote replication, allowing businesses to implement robust disaster recovery solutions. These capabilities ensure that data remains safe and accessible, even in the event of unexpected incidents.

Another notable characteristic of the Dell 3000i is its management interface. The system is equipped with an intuitive and user-friendly management console that simplifies administrative tasks. This console provides real-time insights into performance metrics, storage utilization, and system health, enabling IT administrators to make informed decisions quickly.

In conclusion, the Dell 3000i stands out as a reliable and efficient storage solution for organizations seeking to enhance their operational capabilities. With its high performance, flexibility, and robust data protection features, it effectively supports the growing data demands of today’s digital landscape. Businesses looking for a storage system that can evolve with their needs will find the Dell 3000i to be a compelling choice, combining advanced technology with user-friendly management for optimal data handling.