Dell 3000i manual Connect to the Target Storage Array from the Host Server

Page 54

Step 7: Connect to the Target Storage Array from the Host Server

If you are using Windows Server 2003 or Windows Server 2008 GUI

1Click StartProgramsMicrosoft iSCSI Initiator or StartAll ProgramsAdministrative ToolsiSCSI Initiator.

2Click the Targets tab.

If previous target discovery was successful, the iqn of the storage array should be displayed under Targets.

3Click Log On.

4Select Automatically restore this connection when the system boots.

5Select Enable multi-path.

6Click Advanced and configure the following settings under the General tab:

Local Adapter: Must be set to Microsoft iSCSI Initiator.

Source IP: The source IP address of the host server you want to connect from.

Target Portal: Select the iSCSI port on the storage array controller that you want to connect to.

Data Digest and Header Digest: Optionally, you can specify that a digest of data or header information be compiled during transmission to assist in troubleshooting.

CHAP logon information: If CHAP authentication is required, select this option and enter the Target secret.

Perform mutual authentication: If mutual CHAP authentication is configured, select this option.

NOTE: IPSec is not supported.

7Click OK.

To support storage array controller failover, the host server must be connected to at least one iSCSI port on each controller. Repeat step 3 through step 8 for each iSCSI port on the storage array that you want to establish as failover targets (the Target Portal address will be different for each port you connected to).

NOTE: To enable the higher throughput of multipathing I/O, the host server must connect to both iSCSI ports on each controller, ideally from separate host-side NICs. Repeat step 3 through step 7 for each iSCSI port on each controller. If using a duplex MD3000i configuration, then LUNs should also be balanced between the controllers.

The Status field on the Targets tab should now display as Connected.

8Click OK to close the Microsoft iSCSI initiator.

NOTE: MD3000i supports only round robin load-balancing policies.

54

Setting Up Your iSCSI Storage Array

Image 54
Contents Systems Installation Guide February Contents Configuring iSCSI on your Storage Array If you are using Windows Server 2008 Core VersionIf you are using Rhel 5 or Sles 10 SP1 Guidelines for Configuring Your Network for iSCSI Contents Management Station Hardware Requirements IntroductionSystem Requirements IntroductionIntroduction to Storage Arrays Hardware Installation Storage Configuration PlanningAbout the Enclosure Connections Direct-Attached Solutions Cabling the EnclosureRedundancy vs. Nonredundancy Private network Controller Hardware Installation Two-node cluster Ethernet Two host serverMD3000i RAID Four host server Port ControllersCorporate, public or private network Network-Attached Solutions Enclosure dual Private network ControllersIP SAN Gigabit Ethernet Host servers Ethernet switch Attaching MD1000 Expansion Enclosures Expanding with Previously Configured MD1000 Enclosures Expanding with New MD1000 Enclosures Hardware Installation Software Installation System Assembly and StartupSoftware Installation To install the iSCSI initiator during Rhel 4 installation Installing the iSCSI Initiator on a Windows Host ServerInstalling the iSCSI Initiator on a Linux Host Server To install the iSCSI initiator after Rhel 4 installationTo install the iSCSI initiator during Rhel 5 installation To install the iSCSI initiator after Rhel 5 installationTo install the iSCSI initiator during Sles 9 installation To install the iSCSI initiator after Sles 9 installationInstalling MD Storage Software Software Installation Command to manually mount CD is When the installation completes, click Done Installing a Dedicated Management Station Windows and Linux Viewing Resource CD Contents Installing the ManualsDocumentation for Windows Systems Documentation for Linux Systems Insert the CDInstalling the Manuals Array Setup and iSCSI Configuration Before You StartTerminology Storage array ISCSI Configuration WorksheetManagement station TargetISCSI controller 0, SubnetDefault gateway Setting Up Your iSCSI Storage ArrayStatic IP address storage array ISCSI controller 1,MD3000i Target ChapUsing iSNS Configuring iSCSI on Your Storage ArrayArray Automatic Storage Array Discovery Default Management Port SettingsDiscover the Storage Array Out-of-band management only Manual Storage Array DiscoverySet Up the Array Addresses on each controller Initial Setup Tasks→ ConfigureUpdate your management station Ethernet Management Ports, thenConfigure the iSCSI Ports on the Storage Array If you are using Windows Server 2008 Core Version Start the iSCSI service sc start msiscsiPerform Target Discovery from the iSCSI Initiator If you are using Linux Server If you are using Rhel 5 or Sles 10 SP1 Etc/init.d/iscsi restartIscsiadm -m node -T initiatorusername -p targetip -u Configure Host Access Target Chap Understanding Chap AuthenticationWhat is CHAP? Mutual ChapHow Chap Is Set Up Chap DefinitionsChap Types Defined Description Configure Chap Authentication on the Storage Array optional Configuring Target Chap Authentication on the Storage ArrayChap Settings Selection Description None Configuring Mutual Chap Authentication on the Storage Array Configure Chap Authentication on the Host Server optional IPaddressofiSCSIportonstoragearray CHAPusername CHAPpassword Setting Up Your iSCSI Storage Array If you are using Rhel 5 or Sles 10 SP1 If you are using SLES10 SP1 via the GUI Connect to the Target Storage Array from the Host Server TCPPortNumberOfTargetPortal is If you are using a Linux Server Iscsicli SessionListViewing the status of your iSCSI connections Optional Set Up In-Band Management Premium Features Troubleshooting ToolsSetting Up Your iSCSI Storage Array Uninstalling Software Uninstalling From WindowsUninstalling Software Uninstalling From Linux Uninstalldellmdstoragemanager and press EnterGuidelines for Configuring Your Network for iSCSI Windows Host SetupNetwork Configuration Guidelines Linux Host Setup Configuring TCP/IP on Linux using Dhcp root users only NETWORKING=yes HOSTNAME=mymachine.mycompany.comNetwork Configuration Guidelines Index Linux, 64 static IP, 63 WinsIndex RAID

3000i specifications

The Dell 3000i is a powerful and versatile storage solution designed to meet the needs of modern businesses. Known for its flexibility and efficiency, this entry-level storage array offers a range of features that cater to small to medium enterprises and branch offices, providing them with reliable, scalable, and high-performance data management capabilities.

One of the standout features of the Dell 3000i is its impressive performance. It is powered by Dell's proprietary technology, enabling it to handle various workloads with ease. With support for both block and file storage, the 3000i allows organizations to streamline their data operations and optimize their storage strategies. This flexibility means that regardless of the specific requirements, users can manage their data efficiently and effectively.

The Dell 3000i supports multiple connectivity options, including iSCSI and Fibre Channel, ensuring that it can be integrated seamlessly into existing IT environments. This versatility allows organizations to leverage their current infrastructure while capitalizing on the advanced capabilities of the 3000i. Additionally, it features a modular architecture, enabling users to scale their storage incrementally as their needs grow. This means businesses can start with a small footprint and expand their storage capacity without any disruption.

Data protection is a critical concern for all organizations, and the Dell 3000i addresses this with advanced RAID configurations, which safeguard data against hardware failures. Furthermore, it includes features such as snapshots and remote replication, allowing businesses to implement robust disaster recovery solutions. These capabilities ensure that data remains safe and accessible, even in the event of unexpected incidents.

Another notable characteristic of the Dell 3000i is its management interface. The system is equipped with an intuitive and user-friendly management console that simplifies administrative tasks. This console provides real-time insights into performance metrics, storage utilization, and system health, enabling IT administrators to make informed decisions quickly.

In conclusion, the Dell 3000i stands out as a reliable and efficient storage solution for organizations seeking to enhance their operational capabilities. With its high performance, flexibility, and robust data protection features, it effectively supports the growing data demands of today’s digital landscape. Businesses looking for a storage system that can evolve with their needs will find the Dell 3000i to be a compelling choice, combining advanced technology with user-friendly management for optimal data handling.