Packard Bell M5801 manual Standard Assembly Process, Opening the chassis

Page 44

Standard Assembly Process

1.Opening the chassis

1.1 Remove the two screws

1.2Remove side cover

2.Removing front bezel and HDD Cage

2.1 Pushing three hooks

38

Image 44

Contents Ixtreme M5801 Service Guide Date Chapter Updated Revision HistoryCopyright Conventions Preface 103 Introducing the Motherboard IntroductionFeatures Bios Firmware Dimensions and weightExpansion Options Integrated I/OMainboard Components Label ComponentCintrusion Block Diagram Ixtreme M5801 Icon Component DescriptionUSB ports Connects to USB 2.0 devices USB mouse, USB camera Rear view 1CH Audio Jack Function TableColor/Use Headphone Port Introduction Component DescriptionSystem Peripherals Mouse PS/2 or USB, manufacturing optionKeyboard PS/2 or USB, manufacturing option SpeakersCard Reader Option Hardware Specifications and Configurations Bios Hotkey ListSpecification Main Board Major ChipsSystem Memory Cache MemoryVideo Interface Audio InterfacePower Management IDE InterfaceUSB Port Devices Idle Shut DownPower Management Function Acpi support function Device Standby ModeGlobal Standby Mode Suspend ModeUsing Bios About the Setup UtilityStandard Configuration Entering the Setup UtilitySetup Utility Menus Updating the Bios Product Information Item HelpStandard Cmos Features Date and TimeHalt On All, But Keyboard UAHCI Port1 /Port2 /Port3 /Port4 /Port5 /Port6A.R.T. Auto Quiet Boot Enabled Advanced Bios FeaturesQuick Boot Enabled UHard Disk Drive Priority Press Enter Removable Device Priority Press Enter Boot Up NumLock On USB Beep Message DisabledAdvanced Chipset Features Integrated Peripherals Power Management Setup Deep Power Off Mode EnabledPower On by RTC Alarm Disabled Power On by PCIE/PCI Devices DisabledRestore On AC Power Loss Last State Wake Up by PS/2 KB/Mouse EnabledWake Up by USB KB/Mouse Enabled Smart Fan Enabled PC Health StatusFrequency/Voltage Control Enable Clock to All DIMM/PCI EnabledSpread Spectrum Enabled Bios Security Features Supervisor Password Not InstalledUser Password Not Installed Change Supervisor Password Press EnterLoad Default Settings Save & Exit SetupMachine Disassembly and Replacement General Information Before You BeginRemoving front bezel and HDD Cage Standard Assembly ProcessOpening the chassis Page Install the PSU Setting the MotherboardPage Page Assembly motherboard Page Insert the ODD/HDD ODD Installed on SATA4 HDD Carrier Installed on SATA3 Master HDD Installed on SATA1 Slave HDD Installed on SATA2 Close the Front Bezel Insert Add-on cardPage Page Install system fan Overview Removing the Front Bezel Standard Disassembly ProcessOpening the computer Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the System Fan Removing the Main BoardPage Page Removing the power-supply Removing the HDD in HDD Carrier Page Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Post Error Messages List Bios Messages Action/FRUSpecifics about the type and location of the memory error Error Symptoms List Error Symptom Action/FRU Processor / Processor FanMain board and Memory Hard Disk DriveError Symptom Action/FRU CD/DVD-ROM Drive AudioError Symptom Action/FRU Video and Monitor Power SupplyParallel/Serial Ports KeyboardError Symptom Action/FRU Other ProblemsUndetermined Problems Jumper and Connector Information Safety PrecautionsInstalling the Motherboard in a Case Choosing a Computer CaseChecking Jumper Settings Setting JumpersJumper Type Description Setting Default IIIustration Checking Jumper SettingsJumper Settings Connecting Case Components Connecting 24-pin power cableSysfan Cooling Fan Power Connector Pin Signal Name Function Pwrfan Cooling Fan Power Connector Pin Signal Name FunctionPin Signal Name ATX12V ATX 12V Power Connector Pin Signal NamePin Signal Name Function Power/Sleep/Message waiting LEDReset Switch Power SwitchBefore installing the Processor Installing HardwareInstalling the Processor CPU Installation Procedure Following illustration shows CPU installation componentsMemory Memory Bus Installing Memory ModulesInstallation Procedure Installing Serial ATA Hard Drives Sata cable optional Sata power cable optionalInstalling Add-on Cards PCIE16X SlotOnboard PCI interface does not support 64-bit Scsi cards Connecting Optional Devices FAUDIO1 Front Panel Audio headerSata 1~6 Serial ATA connectors SPDIFOUT1 Spdif out headerOptionSPIDEBUG1 FRU Field Replaceable Unit List Exploded Diagram ChassisPB 30L w/ HDD carrier ME BOMRAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM 101 102 FRU List