Packard Bell M5801 manual Error Symptom Action/FRU, Other Problems

Page 86

Error Symptom

 

Action/FRU

Executing software shutdown from

1.

Load default settings.

Windows98 Start menu does not turn off

2.

Reload software from Recovery CD.

the system. (Only pressing power switch

 

 

can turn off the system).

 

 

 

 

 

No system power, or power supply fan is

1.

Power Supply

not running.

2.

Main board

 

 

 

 

 

Other Problems

Any other problems.

1.

Undetermined Problems

 

 

 

80

Page 85 Page 87
Image 86
Page 85 Page 87
Contents Ixtreme M5801 Service Guide Date Chapter Updated Revision HistoryCopyright Conventions Preface 103 Introducing the Motherboard IntroductionFeatures Expansion Options Bios FirmwareDimensions and weight Integrated I/OMainboard Components Label ComponentCintrusion Block Diagram Ixtreme M5801 Icon Component DescriptionUSB ports Connects to USB 2.0 devices USB mouse, USB camera Rear view 1CH Audio Jack Function TableColor/Use Headphone Port Introduction Component DescriptionKeyboard PS/2 or USB, manufacturing option System PeripheralsMouse PS/2 or USB, manufacturing option SpeakersCard Reader Option Specification Hardware Specifications and ConfigurationsBios Hotkey List Main Board Major ChipsVideo Interface System MemoryCache Memory Audio InterfaceUSB Port Power ManagementIDE Interface Devices Idle Shut DownGlobal Standby Mode Power Management Function Acpi support functionDevice Standby Mode Suspend ModeStandard Configuration Using BiosAbout the Setup Utility Entering the Setup UtilitySetup Utility Menus Updating the Bios Product Information Item HelpStandard Cmos Features Date and TimeHalt On All, But Keyboard UAHCI Port1 /Port2 /Port3 /Port4 /Port5 /Port6A.R.T. Auto Quiet Boot Enabled Advanced Bios FeaturesQuick Boot Enabled UHard Disk Drive Priority Press Enter Removable Device Priority Press Enter Boot Up NumLock On USB Beep Message DisabledAdvanced Chipset Features Integrated Peripherals Power On by RTC Alarm Disabled Power Management SetupDeep Power Off Mode Enabled Power On by PCIE/PCI Devices DisabledRestore On AC Power Loss Last State Wake Up by PS/2 KB/Mouse EnabledWake Up by USB KB/Mouse Enabled Smart Fan Enabled PC Health StatusFrequency/Voltage Control Enable Clock to All DIMM/PCI EnabledSpread Spectrum Enabled User Password Not Installed Bios Security FeaturesSupervisor Password Not Installed Change Supervisor Password Press EnterLoad Default Settings Save & Exit SetupMachine Disassembly and Replacement General Information Before You BeginRemoving front bezel and HDD Cage Standard Assembly ProcessOpening the chassis Page Install the PSU Setting the MotherboardPage Page Assembly motherboard Page Insert the ODD/HDD ODD Installed on SATA4 HDD Carrier Installed on SATA3 Master HDD Installed on SATA1 Slave HDD Installed on SATA2 Close the Front Bezel Insert Add-on cardPage Page Install system fan Overview Removing the Front Bezel Standard Disassembly ProcessOpening the computer Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the System Fan Removing the Main BoardPage Page Removing the power-supply Removing the HDD in HDD Carrier Page Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Post Error Messages List Bios Messages Action/FRUSpecifics about the type and location of the memory error Main board and Memory Error Symptoms ListError Symptom Action/FRU Processor / Processor Fan Hard Disk DriveError Symptom Action/FRU CD/DVD-ROM Drive AudioParallel/Serial Ports Error Symptom Action/FRU Video and MonitorPower Supply KeyboardError Symptom Action/FRU Other ProblemsUndetermined Problems Installing the Motherboard in a Case Jumper and Connector InformationSafety Precautions Choosing a Computer CaseChecking Jumper Settings Setting JumpersJumper Type Description Setting Default IIIustration Checking Jumper SettingsJumper Settings Connecting Case Components Connecting 24-pin power cablePin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionPwrfan Cooling Fan Power Connector Pin Signal Name Function ATX12V ATX 12V Power Connector Pin Signal NameReset Switch Pin Signal Name FunctionPower/Sleep/Message waiting LED Power SwitchBefore installing the Processor Installing HardwareInstalling the Processor CPU Installation Procedure Following illustration shows CPU installation componentsMemory Memory Bus Installing Memory ModulesInstallation Procedure Installing Serial ATA Hard Drives Sata cable optional Sata power cable optionalInstalling Add-on Cards PCIE16X SlotOnboard PCI interface does not support 64-bit Scsi cards Connecting Optional Devices FAUDIO1 Front Panel Audio headerSata 1~6 Serial ATA connectors SPDIFOUT1 Spdif out headerOptionSPIDEBUG1 FRU Field Replaceable Unit List Exploded Diagram ChassisPB 30L w/ HDD carrier ME BOMRAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM 101 102 FRU List
Top Page Image Contents