Packard Bell M5801 manual Master HDD Installed on SATA1 Slave HDD Installed on SATA2

Page 54

6.9Put five hooks to Chassis and push HDD Cage down

6.10Fix the screw of HDD cage and Pulling in HDD SATA cable on Motherboard

Master HDD Installed on SATA1

Slave HDD Installed on SATA2

6.11HDD/ODD install rule

		SATA1	SATA2	SATA3	SATA4

	HDD+ ODD	HDD	ODD

	HDD+ ODD*2	HDD	ODD	ODD

	HDD*2+	HDD	ODD	HDD	ODD
	ODD*2	HDD	ODD	HDD	ODD
	ODD*2

	HDD+ HDD	HDD	HDD	ODD
	Carrier+ ODD	HDD	Carrier	ODD
	Carrier+ ODD		Carrier

	HDD*2+ HDD	HDD	HDD	HDD	ODD
	Carrier+ ODD			Carrier

48

Image 54

Contents Ixtreme M5801 Service Guide Date Chapter Updated Revision HistoryCopyright Conventions Preface 103 Introducing the Motherboard IntroductionFeatures Expansion Options Bios FirmwareDimensions and weight Integrated I/OMainboard Components Label ComponentCintrusion Block Diagram Ixtreme M5801 Icon Component DescriptionUSB ports Connects to USB 2.0 devices USB mouse, USB camera Rear view Audio Jack Function Table Color/Use Headphone1CH Port Introduction Component DescriptionKeyboard PS/2 or USB, manufacturing option System PeripheralsMouse PS/2 or USB, manufacturing option SpeakersCard Reader Option Specification Hardware Specifications and ConfigurationsBios Hotkey List Main Board Major ChipsVideo Interface System MemoryCache Memory Audio InterfaceUSB Port Power ManagementIDE Interface Devices Idle Shut DownGlobal Standby Mode Power Management Function Acpi support functionDevice Standby Mode Suspend ModeStandard Configuration Using BiosAbout the Setup Utility Entering the Setup UtilitySetup Utility Menus Updating the Bios Product Information Item HelpStandard Cmos Features Date and TimeUAHCI Port1 /Port2 /Port3 /Port4 /Port5 /Port6 A.R.T. AutoHalt On All, But Keyboard Advanced Bios Features Quick Boot EnabledQuiet Boot Enabled UHard Disk Drive Priority Press Enter Removable Device Priority Press Enter Boot Up NumLock On USB Beep Message DisabledAdvanced Chipset Features Integrated Peripherals Power On by RTC Alarm Disabled Power Management SetupDeep Power Off Mode Enabled Power On by PCIE/PCI Devices DisabledWake Up by PS/2 KB/Mouse Enabled Wake Up by USB KB/Mouse EnabledRestore On AC Power Loss Last State Smart Fan Enabled PC Health StatusEnable Clock to All DIMM/PCI Enabled Spread Spectrum EnabledFrequency/Voltage Control User Password Not Installed Bios Security FeaturesSupervisor Password Not Installed Change Supervisor Password Press EnterLoad Default Settings Save & Exit SetupMachine Disassembly and Replacement General Information Before You BeginStandard Assembly Process Opening the chassisRemoving front bezel and HDD Cage Page Install the PSU Setting the MotherboardPage Page Assembly motherboard Page Insert the ODD/HDD ODD Installed on SATA4 HDD Carrier Installed on SATA3 Master HDD Installed on SATA1 Slave HDD Installed on SATA2 Close the Front Bezel Insert Add-on cardPage Page Install system fan Overview Standard Disassembly Process Opening the computerRemoving the Front Bezel Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the System Fan Removing the Main BoardPage Page Removing the power-supply Removing the HDD in HDD Carrier Page Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Post Error Messages List Bios Messages Action/FRUSpecifics about the type and location of the memory error Main board and Memory Error Symptoms ListError Symptom Action/FRU Processor / Processor Fan Hard Disk DriveError Symptom Action/FRU CD/DVD-ROM Drive AudioParallel/Serial Ports Error Symptom Action/FRU Video and MonitorPower Supply KeyboardError Symptom Action/FRU Other ProblemsUndetermined Problems Installing the Motherboard in a Case Jumper and Connector InformationSafety Precautions Choosing a Computer CaseChecking Jumper Settings Setting JumpersChecking Jumper Settings Jumper SettingsJumper Type Description Setting Default IIIustration Connecting Case Components Connecting 24-pin power cablePin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionPwrfan Cooling Fan Power Connector Pin Signal Name Function ATX12V ATX 12V Power Connector Pin Signal NameReset Switch Pin Signal Name FunctionPower/Sleep/Message waiting LED Power SwitchInstalling Hardware Installing the ProcessorBefore installing the Processor CPU Installation Procedure Following illustration shows CPU installation componentsInstalling Memory Modules Installation ProcedureMemory Memory Bus Installing Serial ATA Hard Drives Sata cable optional Sata power cable optionalInstalling Add-on Cards PCIE16X SlotOnboard PCI interface does not support 64-bit Scsi cards Connecting Optional Devices FAUDIO1 Front Panel Audio headerSata 1~6 Serial ATA connectors SPDIFOUT1 Spdif out headerOptionSPIDEBUG1 FRU Field Replaceable Unit List Exploded Diagram ChassisPB 30L w/ HDD carrier ME BOMRAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM 101 102 FRU List